1999 sprinter key programming

[ninja123]

I have a sprinter to make keys for, well, sort of!!

All keys were lost, other guy made new key, now new key lost but old key found, but say start error on dash.

What did first guy do to dissable old key?

Any way of reinstating this key?

Never done a sprinter before so in the dark on this one.

Thanks for any info, ninja

[gokey]

first repair start error

[ninja123]

start error is because van had new keys programmed by someone else, now old keys give start error, so this is not the problem here.

Anyone know a way to re instate old keys?

ninja

[squirrelbandy]

start error is because second key was probably erased ,Ninja best way is to remove immo box and read hc08 ,should be behind cluster , keys can be written in on the bench .
if stuck read dump and post it , also read key and post logic .

[ninja123]

I have never encountered one of these before, i dont have an adaptefor this 64 pin mcu, but i see some connections on the board, can this be read from here?

on mcu is OJ66D

I have xprog m but dont see this mcu in the device list?

Thanks for any help, ninja

[gev]

D66J = MC68HC08AZ32 read in circuit

[ninja123]

thankyou for this info, but please forgive my thickness, where can i get a connector from for xprog m?

I only have a few adapters and i use them all so dont want to butcher them.

also im not quite sure how to follow this diagram, where do i connect the pins marked in blue, and why is there 8 numbers in the red box? need to connect all??

thanks for info,

ninja

[MarkPRP]

You can make it, or just use wires from a plug!

Or bring it over and I can do it for you!

[zoyzoyni]

2.2.3. MC68HC08AZ32A. you read with xprog easy and safe.after if you have zedbul or eny you write the key.or precoded chip ready for start....

[Meat-Head]

WHOA WHOA
READ FIRST

USE THE STALK FUNCTION OF YOUR COMPUTER YOU MUST MUST MUST USE X-PROG AND THE MCU IS SECURED IT WILL BE ERASED, THERE WILL BE NOTHING BUT FF FROM YOU AND THE MCU

RUMOR STATES

1) OBDMASTER DID THIS STALK HIM

2) lUPU_sANDU DID THIS - GO STALK HIM

3) SORYY MEMBER?? LOVES DOING THESE IN CIRCUIT WITH CARPROG CLONE

OR

AS IT IS A TOTAL SCREWUP JOB - GO LEECH ENGINE AND ECU DUMP FROM SOMEWHERE

OR

DOWNLOAD OFF EBAY EMULATOR.

HTH

MEAT.

[ninja123]

You can make it, or just use wires from a plug!

Or bring it over and I can do it for you!

Thanks for the offer mate, I would love to sort this myself, but time is not on my side at the moment, got loads of work on and not enough hours in the day. pm me your whereabouts and ill bring it over and pay accordingly.

BIG thanks, ninja

[ninja123]

WHOA WHOA
READ FIRST

USE THE STALK FUNCTION OF YOUR COMPUTER YOU MUST MUST MUST USE X-PROG AND THE MCU IS SECURED IT WILL BE ERASED, THERE WILL BE NOTHING BUT FF FROM YOU AND THE MCU

RUMOR STATES

1) OBDMASTER DID THIS STALK HIM

2) lUPU_sANDU DID THIS - GO STALK HIM

3) SORYY MEMBER?? LOVES DOING THESE IN CIRCUIT WITH CARPROG CLONE

OR

AS IT IS A TOTAL SCREWUP JOB - GO LEECH ENGINE AND ECU DUMP FROM SOMEWHERE

OR

DOWNLOAD OFF EBAY EMULATOR.

HTH

MEAT.

I read these posts mate, but dont really have the time for trial and error on this one, as the guys ex-wife has the working keys and once she finds where its parked it will go walkies!!

ninja

[squirrelbandy]

Ninja this is for you m8 , might make life easier for you.
pass in pm

sorry for pass but these are my personal pics and dont want them all round the world .

[ninja123]

Thanks mate, but where can i get a plug to fit xprog?

Can I butcher from any car control unit from scrapyard?

If so, which car/make?

Or where to buy from.

Big thanks, ninja

ps, once i have read this mcu, where is key data stored, so i can add old keys back in, cheers

[squirrelbandy]

WL016 - X-PROG/XPRO-M Cable Assembly - 16 WAY Test Supplies | IC Clips & IC Test Equipment | 8 Pin Soic Zif & Adapters (http://www.warwickts.com/wl016--x-progxpro-m-cable-assembly--16-way-p610)

you could try this to connect up to x-prog by pushing into described pins and cut off main plug , thats all you need as its 6 wires needed to be soldered onto board.

[ninja123]

thanks mate, followed you and worked a treat.

I just soldered wires to an existing adapter then removed after.

big thanks mate, ninja

[3abas27]

D66J = MC68HC08AZ32 read in circuit
PLZ REDIND THISCIRCUIT NO NEED ANY PIN TO BE LIFTED?

[ninja123]

I did the 2000 model sprinter ok, but i got a 2004 model today, removed temic immo box, but mcu has strange numbers on, connected as before but cant read?

did these change ??

any info more than welcome, ninja

[Meat-Head]

them strage numbers google them, if you find no mask information you could always carry on emailing spam links to your friends lol

[ninja123]

top of the list matey!!

[Meat-Head]

top of the list matey!!

the mask ID for that immo box or my email addresss?

[ninja123]

my new email folder: SPAM FOR MEATY

ninja :)

[bigkey]

Hi squirrelbandy, is there any chance you can give me access to these pics please. I put up a Vito and 2 Sprinter jobs into hard basket in the last 9 months. So would like to learn about this. Thanks