help ecu edc15 is dead

[pacomasi]

hello
I went to flash EDC15 ecu the audi a3 tdi 110cv year 2000 with galletto and I'm at 25% writing and the ECU did not respond.
I get the eeprom 29F400 and have written Wilem ecu but still no answers.
That may fail in the ecu?
Let's see if anyone can help me thanks


Best Regards

[mexanico1971]

some willem do not write it good !
clean well the pin"s in the adapter get a good ID of the chip and deselect (skip ) box ,if you use Eprom51 !
try to use MPPS on bench it work"s for shore !

[pacomasi]

I tested with galletto the bank but I do not recognize the ecu

[kire106ka]

Post dumps to see maybe dump is not good or as mexaniko says willem is no good for that flash try with other programmer to write ori

[Shmortz]

I use old board Willem PCB 3B v1.3, works like a charm, never had a problem with that kind of flash...

[tanito]

Use mpps with boot mode.

[miha99]

Use 29F400 slow speed to load ori file, if your file is damaged, post numbers from your ECU.

[pacomasi]

hello
I use willem PCB 3B v1.3.
As for the boot mode with mpps?
And I've tried with galletto at low speed and does not work.
I put the original file but okay.
The ecu is 0281010120-038906012A.
I hope you can help me solve the problem thanks

[pablo1971]

some willem do not write it good !
clean well the pin"s in the adapter get a good ID of the chip and deselect (skip ) box ,if you use Eprom51 !
try to use MPPS on bench it work"s for shore !




as stated before-use mpps in boot mode-build ecu up,and mpps will do this correctly...

[thebigf2]

Hello,

you should use secure tools and Solutions.
Cloned galetto is not secure, OBD is not Secure.
(Battery, Protocol,PC failures etc.)

1. Search an Flash Progger with 29Fxx Socket or Adapter
2. desolder the Flash with an hot Air Gun.
3.Clean Pins, and rewrite Ori with Bench Flasher
4. Re Solder the Flash

After re install your ECU will Answer on Bus!

:marchmellow:

[pacomasi]

Hello,

you should use secure tools and Solutions.
Cloned galetto is not secure, OBD is not Secure.
(Battery, Protocol,PC failures etc.)

1. Search an Flash Progger with 29Fxx Socket or Adapter
2. desolder the Flash with an hot Air Gun.
3.Clean Pins, and rewrite Ori with Bench Flasher
4. Re Solder the Flash

After re install your ECU will Answer on Bus!

:marchmellow:
I've already tried that and it does not work thanks

[pacomasi]

Hello and this solved the welding was not to contact eprom.
But I wonder how it's done in boot mode with mpps step by step thanks

[pablo1971]

with mpps-go into generic.there you will see edc15

wire up ecu on bench....and use mpps to id the ecu,then use boot to load file to ecu...

[miha99]

If willem doesn`t cure the problem and if you load to flash correct dump than problem is somewhere else!

[pacomasi]

If willem doesn`t cure the problem and if you load to flash correct dump than problem is somewhere else!
Hi I have solved the problem than you

[darius89]

how you solved ?????

[jp_olli]

Hello and this solved the welding was not to contact eprom.
But I wonder how it's done in boot mode with mpps step by step thanks

Guess bad soldering was the cause. :)

[colouny]

with mpps-go into generic.there you will see edc15

wire up ecu on bench....and use mpps to id the ecu,then use boot to load file to ecu...

Dude thanks for the info, you are the first on the internet to write how to use the MPPS boot mode in words, not just saying try the boot mode.
Thanks again.