PDA

View Full Version : Peugeot 307cc me7.4.4 109hp



beltronics
25th March, 2013, 11:39 PM
Hello!
I have this switchboard
188148188149

Doing this then can I read and write for obd?
188150

thanks.

OVERSPEED
26th March, 2013, 12:16 AM
ME7.4.4 is diferent from ME7.4.5 (the photo says ME7.4.5)

beltronics
26th March, 2013, 12:20 AM
Where can I obtain of ME7.4.4?

carmageddon
26th March, 2013, 08:28 AM
your ecu is ME7.4.5, the label is not important for establish method work.

the processing in picture are only for boot mode on table ME7.4.5 but not for obd R-W....piasini and fg2 can do not boot mode for ME7.4.4

kennfeld
26th March, 2013, 09:36 AM
can been done obd with evc tool

beltronics
26th March, 2013, 02:22 PM
your ecu is ME7.4.5, the label is not important for establish method work.

the processing in picture are only for boot mode on table ME7.4.5 but not for obd R-W....piasini and fg2 can do not boot mode for ME7.4.4
What do I need to read and to write?

carmageddon
26th March, 2013, 02:27 PM
for example : KTAG (boot), KESS2 (obd or boot), KESS1 (obd), fg1 and fg2 (obd)

beltronics
26th March, 2013, 02:41 PM
I will try with FG2
thanks

elangel0001
26th March, 2013, 02:59 PM
you beltronic confusion by google translator


DAB is the translator actually said OBD


regards

kennfeld
26th March, 2013, 10:24 PM
use bosch boot pin method ....
must work

elangel0001
26th March, 2013, 11:17 PM
use bosch boot pin method ....
must work


what would be the boot mode for reading obd fg1?

elangel0001
27th March, 2013, 05:52 PM
impossible without boot, gets caught 2 minutes then gives error message.


regards

carmageddon
27th March, 2013, 06:07 PM
if you don't have updated dialog protocol, or official tools, it's impossible to do boot mode on me7.4.4...fg1/2 don't work!

working protocol is only on kess2, cmd and other official tools

elangel0001
27th March, 2013, 06:59 PM
no, I have never updated the ecu refers lexia via "downloading"


regards

kennfeld
27th March, 2013, 11:12 PM
it work on the official tool so maybee you have clone ?

elangel0001
27th March, 2013, 11:50 PM
if I have lexia March 2012


What should make a tele-load?

Zmann
28th March, 2013, 01:56 AM
virginise eeprom and telecode

elangel0001
28th March, 2013, 12:14 PM
ok, I'll try, SW PP2000 recommend?


thanks

elangel0001
29th March, 2013, 05:08 PM
hello


for Virginizear the eprom ECU use PP2000 better? I own DiagBox 7.08 and PP2000


Any help before you do?


regards

Zmann
29th March, 2013, 05:28 PM
Hope I got your question correctly! Neither PP2000 nor DB can virginise ECU's. Your jobs are to virginise then to telecode.
You need a good virgin file to be programmed into eep 95160 (by a programmer). And PP2000 or DB both are good for telecode.

elangel0001
29th March, 2013, 07:22 PM
XXXXXXXXXXXXXXXXXXXX


regards

EDIT: sorry ... I understand now would buy a desoldering and soldering e2prom virgin + telecode with PP2000.


this would be the memory to use?

http://i1123.photobucket.com/albums/l549/elangel0001/be78fc90c5_zpsd6a88705.jpg

Zmann
30th March, 2013, 01:42 AM
Yes, you can use it, but just FYI, suffix '6' after W indicates it's not an automotive grade, heat tolelance can be lower!
Why not programming to the orginal chip? 100% safe to deslodering but it can also be programmed in circuit.

http://i262.photobucket.com/albums/ii116/charl_ze/MVC-004F_zpsa65de484.jpg

elangel0001
30th March, 2013, 02:22 AM
hello


thanks for the identification of E2PROM memory.


I ordered!!, load a virgin file which I need a programmer? and what would be the way to write the file e2prom virgin? I do not have this memory programmer.


regards

Zmann
30th March, 2013, 03:23 AM
Hi,

Function of programming such SPI eeprom is quite common and presented on various programmers.
Xprog-m and UPA can also do. Which the programmer do you have?

To virginise to the used ECU's is not so easy (at least by a newbie), suggest a search for an existing virgin file matched to the ECU!

edit: I meant to make a virgin file yourself is not that easy.

elangel0001
30th March, 2013, 04:09 AM
hello


best buy you the first of a junkyard ecu better,programmer XPROG-m v5.0 has a good affordable buy one, what is not clear to me as a tune file Virginize expecial? I weighed it was let to bytes 0 0 0 0, so I wanted to weld a new memory without more.


Thanks for your time!

elangel0001
30th March, 2013, 02:07 PM
ok, already clear

Otocheck - virgin dump
X-pro-m - read and write
PP2000 - telecode



thanks