PDA

View Full Version : Remove DPF nissan qashqai 2.0dci 150hp



anouarabd
28th March, 2013, 12:29 PM
Hi,
need help for remove fap for nissan qashqai 2008 2.0 dci 150hp

thanks

Baddog84
28th March, 2013, 02:09 PM
test and reports
pass pm

anouarabd
28th March, 2013, 05:08 PM
hi baddog
thanks, i will try that

anouarabd
28th March, 2013, 07:46 PM
hi
the car dont start now
i think because injector
need help pls
thanks

bmgadam
28th March, 2013, 07:50 PM
You correct the checksum ?
If yes, check nozzle codes.

anouarabd
28th March, 2013, 08:56 PM
i use kessv2 normally calculate checksum.
i write the original file have same problem
with bosch kts have injector code AAAAAAA for 4 and impossible to change the code

bmgadam
28th March, 2013, 09:08 PM
You must always read nozzle codes before read flash....

darius89
28th March, 2013, 09:53 PM
Payed solution......always good solution ;)

Free solution 90% you in trouble.

Sorry , but that s happens.

Baddog84
29th March, 2013, 08:39 AM
If the codes are gone, it is too late anyway. The Nissan workshop can program the codes. If the codes are not gone, you can tune the controller via BDM. It does nothing. About the OBD codes are partly even after the read off the engine software.

assitutto
29th March, 2013, 03:36 PM
i have same problem today with nissan xtrail 2.0dci 150hp
read and write with kess v2 original and car don't start
i write back ori file with kess and recode injector with launch x431 and car start but don't go over 1500rpm
i think i have to go in nissan for recode injector with nissan diag :(

assitutto
29th March, 2013, 05:12 PM
Update: problem solved with BrainBee BTouch, that diag can recode injector correctly, and car run fine :)

anouarabd
29th March, 2013, 08:39 PM
hi
I tried with launch diagun but same problem than bosch kts : impossible
I will try with renault clip and autocom
thanks

kennfeld
29th March, 2013, 08:53 PM
i Prefer to use cmdflash tool to do this cars ....

anouarabd
30th March, 2013, 12:41 PM
hi
I have error immo P1612
I think because that dont start

assitutto
1st April, 2013, 03:50 PM
i had the same error mate, recode injector and p1612 disappear

anouarabd
2nd April, 2013, 01:59 PM
hi assitutto
dont can recode injector with bosch kts, launch diagun and autocom
with which tool can recode them
I will read ecu with bdm, is possible to recode them directly via dump?
thanks

bmgadam
2nd April, 2013, 02:09 PM
hi assitutto
dont can recode injector with bosch kts, launch diagun and autocom
with which tool can recode them
I will read ecu with bdm, is possible to recode them directly via dump?
thanks

If you read this via BDM, you dont have to recode injectors. Only via OBD

assitutto
2nd April, 2013, 04:27 PM
i use BrainBee BTouch 9000 for recode injector
launch, bosch and autocom can't recode injector

albematty
2nd April, 2013, 05:54 PM
I had the same problem but with diagnstic
bosch I solved the problem you have written so many times and it works