question about MB cls year 2007 and s klasse (w221 year 2005)

[honingkoning]

Question about this cars,

What tools will do this cars (i know that there are a lot of locations, but i only need dash and ezs or can blocker would also be ok).

Wbr Adam.

[pierre renault]

tools for cls 2007 (enigma ,elprosys,digiprog,digimaster,diga,dashcoder for obd)
tools for w221 (enigma,elprosys,digiprog,digimaster,dashcoder for obd )

[javyb]

Smelecom Datasmart 3+ can do the w221 dash. EZS & ZGW gateway by OBD without CAN blocker, CLS by OBD by blocking synchro with EZS although you can use 9s12 to do EZS

[pepi]

Also AVDI will do them booth from OBD with blocking sync between EZS and dash, and all other places were the km are stored.

[honingkoning]

Thanks Guys

i know all the magic machines can do this Cars, but i dont have them.
Most importend for me is what tool can do ezs (Will rosfar red do it) Or is it Same as w204 and not supported by rosfar.

Wbr Adam.

[pierre renault]

w221 not supported

[Ding-Dong]

although you can use 9s12 to do EZS

not a 9s12
its nec in ezs

[javyb]

not a 9s12
its nec in ezs

NEC in CLS??

[Ding-Dong]

NEC in CLS??

oops!
i thought u were about w221.

[bkenigma]

Only tool that will do all locations and Dash.ezs/cgw obd is AVDI. Dont waste your money on anythng else. PM ME

bkenigma

[lama23]

Cls 2007 defo 9s12 and the s class 221 is worth looking at as early ones (2005/06) had 9s12 also.

[Speedosoft]

Bkenigma no tool does the NEC ezs modules; at least none of the known tool,...not even Avdi. All it does is to reflash the gateway to fool the DAS when it tries to read the KM from it. I hope that's what you meant.

Regards.

[javilette]

the question of the year , DIGIPROG CLONE can do it this ?????????????????

[diagtech]

The only machine to do 221 is original elprosys dp3 which also does cls digi clone will do cls by blocking eis and will also do 221 obd if it has been done before by dp3 or you can put new eis in and do dash

[javyb]

The only machine to do 221 is original elprosys dp3 which also does cls digi clone will do cls by blocking eis and will also do 221 obd if it has been done before by dp3 or you can put new eis in and do dash

The smelecom DSP3 also dies w221 by OBD without a CAN blocker

[javilette]

i done some w221 whith dp3 elprosys i khow this , but i buy a new digiprog clone and for example it have w204 ezs in menu , i think the original work whith this whithout blocker, i prefer do it whit my dp3 elprosys but i want to khow if whith 400 euros of machine you can do this too

[diagtech]

No only dash on w221 with digiprog on ezs menu it says install can blocker

[rukartinatv]

You can doit with digiprog w212 w204 with out any problem but in ezs will be 999987 and digi do this car like 1 min go to w204 or w212 press ezs dont go to the dash!!!!
But i think if you wont to doit right way do it with dp3

[Daniulis]

Bkenigma no tool does the NEC ezs modules; at least none of the known tool,...not even Avdi. All it does is to reflash the gateway to fool the DAS when it tries to read the KM from it. I hope that's what you meant.

Regards.

Yes, that what these tools do by OBD, and (just in case) if in this way clocked mercedes will goes to dealer, and the Gateway will be updated, the miles will comes back.

[TULGEYWOODMAN]

Question about this cars,

What tools will do this cars (i know that there are a lot of locations, but i only need dash and ezs or can blocker would also be ok).

Wbr Adam.


Assuming you want to do only dash and ezs, you never said you need to do them via obd.......SO, the answer is simple........and cheap.......


1. UPA
2. ROSFAR RED CLONE
3. CAN FILTER

seemples


rgds

[diagtech]

Dont forget mercedes dealer know about can gateway so if going in merc you have same problem as flashing gateway if they find it

[TULGEYWOODMAN]

Dont forget mercedes dealer know about can gateway so if going in merc you have same problem as flashing gateway if they find it
That applies no matter what tools you use.