New shape accord 2008 93c86 what calc?

[cheester]

Can someone help me change mls in accord 2008 with 93c86, tried tachosoft but no luck.
Original mileage is 137912mls, need 70125mls. Attached two readings normal and x16.

Car is 30km from my place and have just clocks.

Thanks for help.

[digimile]

hi
i think dump is not good...2008 has c76 ...please check again...thanks

[bkenigma]

Bin is fine, here is your requrested file. If it were 93c76 I could have cleared maintenance also.

190571

bkenigma

[bkenigma]

190572I got a good read for your miles on the 93c86,but many say 93c76. I made your 70k and cleared servie if you make mistake and its 93c76. So try the c86 that you beleive it is as it should work no issue but if it is 76 you can use this file and I have also reset maintence for you i the eeprom

bkenigma

[cheester]

Please check attach picture of chip

http://s23.postimg.org/ulzwjw47b/20130404_205623.jpg (http://postimg.org/image/ulzwjw47b/)

BKenigma much appreciate for your help. Will test and report tonight.
Will you share how did you manage this clock? What calc?

[digimile]

hi
show front of dash...thanks

[cheester]

bkenigma can you please check the file again, tried upa and xprogm and can not write your full bin.
Look on attached screen, file is full of changes. That is correct?? Can someone confirm its correct?

http://s14.postimg.org/dt6jcq3kd/wrong.jpg (http://postimg.org/image/dt6jcq3kd/)

After write epprom I always do reading to confirm and some part of dump is always different. Looks like some part can not be changed.
Even can not erase fully this epprom

[cheester]

Picture of clock

http://s21.postimg.org/qtaifd9gz/20130404_170524.jpg (http://postimg.org/image/qtaifd9gz/)

[ozibo]

maybe your file is corrupted. try this dump and reply.

[scip2]

have you try to power up the clock? i don't think your file is good

[cheester]

Thanks Ozibo I will try, but how bkenigma could see right mileage?? You have seen right mls on my file?
I've never read in-circuit when I have possibility to unsolder epprom and this time was the same.
Before I read by UPA I unsolder epprom. Can someone confirm if my epprom is corrupted or no?

scip2 (http://www.digital-kaos.co.uk/forums/members/368161-scip2/)
Car is 30km from me, would like to back to the car with correct file but can I powered on the table this clock and will show me the mls?

[fear_dark]

try it and report !!!

[digimile]

hi
i never come across this but my friend baught this car 2 months ago..if i get chance i read and send the file here...thanks

[yugo45]

bkenigma can you please check the file again, tried upa and xprogm and can not write your full bin.
Look on attached screen, file is full of changes. That is correct?? Can someone confirm its correct?

http://s14.postimg.org/dt6jcq3kd/wrong.jpg (http://postimg.org/image/dt6jcq3kd/)

After write epprom I always do reading to confirm and some part of dump is always different. Looks like some part can not be changed.
Even can not erase fully this epprom
File X16 was corrected , not reg.

[martij976]

Here is my file per request. c76 no go... c86 show 130006. New one should be about 70k. To test: pin 17 +, pin 21 -. Hope that helps!

[cheester]

martij976 (http://www.digital-kaos.co.uk/forums/members/192315-martij976/) are you sure that this clock can be powered on the table? Tried your instruction and nothing.
Clock not swich on....hope its not damage now. Will go to the car and report soon.

[scip2]

http://www.digital-kaos.co.uk/forums/f174/steps-how-find-dash-pin-out-303825/

you can try this to find power up

[cheester]

Dash is working, I've use bkenigma file and wrote x16 and 70125 is on the dash. Well done.
Would like to thank everyone for great help!!

[bkenigma]

That file also should have cleared the maintenance records which is why you saw all the changes. Calc is custom made for iprog. I'll post a screenshot so you can see later today
Glad it worked for your, Im assuming you wrote x8 first and not x16 :)

bkenigma

[cheester]

Yes it was my mistake, I compared normal with your done x16 as you put together 2 files on post no3. The maintenance records wasn't clear but that's no problem, done with Honda HDS. Waiting for your screenshot. Thanks again for help!

[cheester]

Thread going on live again :) needles are not working good. I didnt check it as never touch the needles.
Epprom is on the back. Easy access.
Customer saying that revs are showing 500rpm on neutral and speed in gps is 120kmh and in car 80kmh
Will get car again 2morrow and try others dumps posted here.
Someone had similar situation with honda`s?

[bkenigma]

Let me repost it for you, usually when you have needle problems its wrong x8 x16. I'll double check

bkenigma

[cheester]

I tried all dumps from here and only one Ozibo is working.
Needle are working ok, RMP is on 700-800rpm , speed is ok only 8km/h difference to GPS.
Just got some info code on dash, PTG check- its Electric Tourer Boot Failed
Files from others are without faults on dash but needles doest work properly.

Bkenigma did you check your file?

Can some one check this again to have needles working with no faults on dash?

[automan123]

So its mean ozibo dump match your instrument part number.....nothing to do with the code

[cheester]

Automan123 if I put ori file back there is no any PTD check.
There is nothing to do with part number i think as all files here are mod of my ori file.

[automan123]

You have edited ur post......earlier you don't said about PTD check......so maybe im wrong.

[cheester]

Any solution for this clock mates :)

[cheester]

Mates how to make this file working? When changing data like tachosoft saying I have right mileage but needles are not working properly.
There is some checksum, Ozibo file is from different car cause few things doesn't work on the clock.

There is no solution for this model??

[cheester]

Ok my ori dump is corrupted, write back my ori and same problem with needles :( dont know how it was happened.
Unsolder and read by upa and there you go....first time ever...dont understand.

Can someone please post dump for Accord 2.2 iDETC 2008-2009 manual...
Ozibo file is ok, needles working, mileage ok just info check error PDT check on clock...and arrows doesn't light up when gear need to be changed.

Thanks for help!

[automan123]

Automan123 if I put ori file back there is no any PTD check.
There is nothing to do with part number i think as all files here are mod of my ori file.

And now its something to do with a part number right ? Post your parts # here and hope someone have it.

[cheester]

Now when dump is corrupted you right, thats the part
http://s14.postimg.org/r6etnivzx/20130418_191053.jpg (http://postimg.org/image/r6etnivzx/)

[cheester]

sorted, clock is working. Got working dump.