Toyota Corolla 2007 1.6

[myma7up]

any one can help me to program this remote
Toyota Corolla 2007 1.6

[Ashraf6119]

Have you looked in Autodata...........

[myma7up]

ya I have tried two ways from Autodata

[NZBrakelathes]

Www.programmyremote.com
Or something like that
Great info

[myma7up]

http://img856.imageshack.us/img856/8455/91351429.jpg (http://imageshack.us/photo/my-images/856/91351429.jpg/)

[NZBrakelathes]

http://www.programyourremote.com/
Oops

[myma7up]

Www.programmyremote.com (http://Www.programmyremote.com)
Or something like that
Great info
It's not supported in my area :(

[NZBrakelathes]

Try models before or after
Have a play
Often a different model or year will work
It's a USA site but the info is often there in later or earlier models
Or try find out what USA model uses that remote and try the procedure

[myma7up]

Free Keyless Remote Fob Entry programming instructions, procedures for all automotive vehicles (http://www.programyourremote.com/)
Oops
it's the same way in the autodata
not ok with my car

[myma7up]

Try models before or after
Have a play
Often a different model or year will work
It's a USA site but the info is often there in later or earlier models
Or try find out what USA model uses that remote and try the procedure
on this site one way from 2003 to 2008 for corolla
i will search for another site

[NZBrakelathes]

Try other models around the year you need

[myma7up]

Try other models around the year you need
in toyota all model from 2003 to 2008 have the same

[myma7up]

191545
I have found this button
and use it to program this remote
but not going ok with me
any body know what is this for ??

[magdyman]

Hello my dear
if the remote picture is the above one this is the steps
1- switch the ignition on and off 5 times
2- then leave it on after hazared light flashing
3 - press lock button twice
if programming ok hazared will flash
then remove key from igntion and try to test

Good Luck

[autoecu]

Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.