New Kryptview Firmware 19/03/09

[stroner]

Kryptview 19/03/2009

Digital Kaos - Downloads - Kryptview A750 + A700 19/03/09 (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/kryptview-a750-a700-19-03-09-645/)

Changes:
--------

- Fix for countermeasure "change of encryption system" in Ireland.

- Minor bug fixes.

As always this file supports both old hardware and new hardware.
As previously stated we will not stop supporting old model box

[davi367]

Are u sure this is a new release and not the 13/03/09.


(EDIT) sorry for doubting you my friend it is indeed a new release

[bugaloo41]

Ronster cheers mate much appreciated. Am i reading this correctly that it fixes N3 - surely not. If it does the price of the box will go through the roof. Mash will be a millionaire LOL.

Anyone in Ireland test this and confirm.

[C64]

The Ireland thing is very interesting indeed :)

[satman]

it will be a n2 fix ;)

[stroner]

N2 only guys!

Ireland is currently using N2 and N3 simultaniously

[DW190]

Mash will be a millionaire LOL.


Again ? ! :eek:

[glic83]

sounds promising in relation to the Irish issue in relation to the n2 as i had heard that people were doind cards but nothing in the likes of firmware/emu for n2

[wozzo]

Hopefully some keysets will be released so we can get the Dboxs running.

[Donnie Darko]

Hopefully some keysets will be released so we can get the Dboxs running.

Thats whats required,interesting that card must have been opened.

[satman]

Thats whats required,interesting that card must have been opened.

you can only dump the rom110 revA05...
Most of these were updated "over-the-air" to Rom110 REVA07

you need RSA keys as well as opkeys to get dbox( or any other linnux box for that matter ) back running , which will work for now since they havnt started rolling on n2/n3.......

yet...

[red devil]

Thats whats required,interesting that card must have been opened.

the n2 cards in Ireland have been open for some time now but they were only distributed on cable, this fix will last until the areas in question stop streaming n2 and only stream n3 so this can be used to prolong viewing for mmds areas as well

[SP00K]

Thnaks for this as it will b very useful :manuflag:

[squeek77]

need help updating kyrptview box ,hav cable , just haven't got a clue were 2 start, thks

[wilf]

Digital Kaos - Downloads - Kryptview A750 + A700 19/03/09 (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/kryptview-a750-a700-19-03-09-645/) you will need this firmware download to your desktop http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/arnet-kryptview-loader-426/ you will need this loader also put on desktop

[blackink]

I just purchased kyptview 750 have loading instructions have no softwareDownload:

[wilf]

when you've made a few posts you will be allowed access, its best start with an introdution

[gazza2008]

blackink first it is nice 2 say hello 2 everyone

2nd as for your krypt box u need the firmware which is right here >>>>> Digital Kaos - Downloads - Kryptview A750 Firmware 13/03/09 (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/kryptview-a750-firmware-13-03-09-642/)


if you can plz treat this forum with respect as we all here of our own time to help ppl we dont get paid either.

cheers

[trevdub]

hi im new i ordered a kryptview box i live in lreland and am lookin for the new firmware if anyone can help thanks:manusign:

[wilf]

its on the post right above the one you just made its the blue link kryptview 750 19/3/09

[hm12345]

thank you for the update :)

[rami]

Digital Kaos - Downloads - Kryptview A750 + A700 19/03/09 (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/kryptview-a750-a700-19-03-09-645/) you will need this firmware download to your desktop Digital Kaos - Downloads - Arnet Kryptview Loader (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/arnet-kryptview-loader-426/) you will need this loader also put on desktop

Hi
How could I download this update?

Rami

[Dreamer]

You obviously didn't read the post above yours then.
You will need to wait a while for the server to update as that was your first post.



have a look around and maybe you could do an intro post whilst your waiting or check out one of the other sections.

[kickboxerdan]

Hi, Ive just spent a good couple of hours trying to update using the loading instructions in download section, and for some reason, despite the fact that its always worked for me, it just wouldnt go this time.

So I spent ages searching google for answers, and stumbled across alternative instructions, which worked instantly for me!

Make sure before you start you check what COM port your RS232 is on:
1)go to control panel
2)hardware
3)device manager
4)Ports (COM & LPT)
5)Double click on the adapter
6)Click Port Settings
7)Click Advanced
8)Under COM port, change to no. 3

Here we go:
1.Connect STB to PC by null cable/usb to rs232 adapter
2.Start up STB editor/kryptview loader
3.Click on tools
4.Goto code
5.Click on send
6.Click on open
7.Click on the firmware file from your PC
8.Make sure you are on the right com (COM3 if you followed as above, or whatever your setting is otherwise) & FTA MODEL
9.Turn off your STB by the plug
10. Click on start and then turn on STB by plug and it will start to send the data to the STB
11. Wait untill the download is complete and STB will turn back on

Done! Then just follow the usual for re-searching channels.

Thought id just put this up in case anyone else has problems with updating their box.

Hope it helps! Dan

:manusign:

[kgerry]

Thanks Ronster for the info on latest update.

[jessii]

Hi, Ive just spent a good couple of hours trying to update using the loading instructions in download section, and for some reason, despite the fact that its always worked for me, it just wouldnt go this time.

So I spent ages searching google for answers, and stumbled across alternative instructions, which worked instantly for me!

Make sure before you start you check what COM port your RS232 is on:
1)go to control panel
2)hardware
3)device manager
4)Ports (COM & LPT)
5)Double click on the adapter
6)Click Port Settings
7)Click Advanced
8)Under COM port, change to no. 3

Here we go:
1.Connect STB to PC by null cable/usb to rs232 adapter
2.Start up STB editor/kryptview loader
3.Click on tools
4.Goto code
5.Click on send
6.Click on open
7.Click on the firmware file from your PC
8.Make sure you are on the right com (COM3 if you followed as above, or whatever your setting is otherwise) & FTA MODEL
9.Turn off your STB by the plug
10. Click on start and then turn on STB by plug and it will start to send the data to the STB
11. Wait untill the download is complete and STB will turn back on

Done! Then just follow the usual for re-searching channels.

Thought id just put this up in case anyone else has problems with updating their box.

Hope it helps! Dan

:manusign:



Have tried all that got a bit further than usual but says 'The download is not requested'

Any Ideas?

[wilf]

if using laptop it maybe cos you selected wrong comport, if you dont want to change the settings on pc then start at 1 then go up 1 at a time and one will work. if using desktop it maybe cos you have got a serial cable and not a null cable, or it could be you havnt switched box off then pressed start on loader then switched box on to start the download

[nicho123]

Hi, we are using the right com port we checked under device manger. also we are using a maple lead, the one they say is the correct lead.

also we are turning it off then clicking send, then turning the box back on straight away ...

[wilf]

@ jessii and @ nicho123 unless its the same person with 2 registrations, If using laptop you should have 2 cables an rs 232 usb to 9 pin male serial adapter cable and an rs232 9 pin female to 9 pin female null modem cable joined together, check the packaging it came in. however if using vista when you plug in usb in it would normally install the driver for it to work but if xp you may have to install the driver from either the disc that came with the cable or http://www.digital-kaos.co.uk/forums/f10/please-upload-maplin-usb-serial-rs232-drivers-d-12622/?highlight=maplins+driver here when you have that you should be good to go. if using a desktop you only need the rs232 9 pin female to 9 pin female null cable. moral of the story is beg, borrow or steal a desk top they are easier but having said that i mainly use lappy with the driver installed. hope this gets you up and running

[nicho123]

Jess is the wife lol, also we have it linked up correct with the usb into the maplein cable then into the box,

we have the drivers for the usb installed on xp on this lapptop also, but still no luck :(

[wilf]

lol good guess by me tho, begining to really think that your rs232 from maplins is serial cable and not a NULL. do you by any chance have the packaging you will not be able to tell any other way as they look the same but are wired differently inside. either that or your comport settings not correct did you try my earlier suggestion of starting at comport 1 and increasing 1 at a time till you find one that works i know it a pain but you may not have to go far up the order till you have success...... just tried on mine the only time i could get it to say file not reqested was when i didnt turn box back on quickly enuff, try leaving the box off till you got loader ready to go press start then count to 2 then switch box on that works every time for me

[nicho123]

the lead in fine its the one that this site says to get the it says this on the box.


Nikkai

pure connectivity
data - mp3 - digital & analogue display

Serial lead [Null Modem]
order code L71BT

Features
null modem serial connection lead
fully wired
fully shielded cable for error free transmissions



Is that the right lead??

Thanks for all the help

[wilf]

Serial Null Modem 9-Pin Female to 9-Pin Female > Maplin (http://www.maplin.co.uk/Module.aspx?ModuleNo=97740) yes this 1 thats right
We getting there m8, now it can only be your comport settings and box turn on timing you just need to master. i,m off to work so keep posting and someone will help you out if you get stuck. good luck hope you get sorted soon

[nicho123]

yea thats the one i have so why isnt it working lol doing me head in now. i am using the right com port in device manger is says prolific usb-to-serial Comm port (COM6)

so am using com 6, but still it wont download!

I have tryed everything and i just dont no why it wont work :( I WANT MY FREE ~~~~ CHANNELS!!! lol

so try what next lol?? thanks.



Ok ill just wait for you to come bk from work lol.

Also btw ive just tryed every port and still the same.

[wilf]

Nah dont do that you'll miss all 2nites telly keep on with it someone will get you going. this my last roll of the dice m8 before i switch puter off when we say box off we do mean power off altogether at the mains and not on standby off

[nicho123]

yea i no thats what am doing turning it off at the plug

am still trying lol its close to a hammer to it a think

[tim417]

Is this latest firmware for UK & Ireland ? Cheers.

[wilf]

Is this latest firmware for UK & Ireland ? Cheers.

yes it is mate

[Madboy50]

Yeah the kryptview boxes are working in Ireland
a mate has one
(I am still holding out hope for a Dreambox fix

[petey999]

do i need to upload loader then firmware then the patch,thanks

[wilf]

you need to download loader Digital Kaos - Downloads - Arnet Kryptview Loader (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/arnet-kryptview-loader-426/) you need to download firmware Digital Kaos - Downloads - Kryptview A750 + A700 19/03/09 (http://www.digital-kaos.co.uk/forums/downloads/arnet-kryptview/31/kryptview-a750-a700-19-03-09-645/) save them to desktop

[jude]

HI ALL LOOKING FOR KRYPVIEW FIRMWERE LATEST PLEASE

[gar11]

Thnaks for this:celticscarf:

[dominic28]

Thanks for this, great :)