View Full Version : OPEL EDC17 Tricore
enigmauk
15th May, 2013, 11:56 PM
198542
Does anyone know of a tool that can read/write this ECU? Seems Galletto/K-TAG doesn't support this one :(
Thanks
Alpinesport
16th May, 2013, 07:55 AM
every pro and ori tool it is a tc 1767 3 point and boot
enigmauk
16th May, 2013, 08:20 AM
Can you name one that does? I don't mind buying a tool to do this car just need to get job done!
Many dealers told me that this can be done but when they see the ECU pictures they told me their tool doesn't support it.
Thanks
mislav88
16th May, 2013, 10:45 AM
just put ecu in boot and read as any other 1767
pins 3 and 10 of tricore to gnd (via 1k resistor)
pin 4 to +3.3V (1k resistor)
if this dont work put also pin 32 to gnd
mishu_b
16th May, 2013, 12:51 PM
I have done many of this with FGTech 2 tool!
100% working
enigmauk
16th May, 2013, 06:08 PM
Where did you find the boot pin diagram and was the ECU exactly same as above?
mtronik
24th May, 2013, 10:33 PM
connection ecu
mtronik
26th May, 2013, 10:03 AM
pdf tricore galletto v3
enigmauk
26th May, 2013, 11:35 AM
PERFECT!!
will this work with galletto 2 though ?
Thanks
mislav88
26th May, 2013, 02:43 PM
now read my post #4 again...
yes it will work with fgtech2
mishu_b
26th May, 2013, 07:04 PM
as I told - I have done many of this with FGTech 2
enigmauk
12th June, 2013, 11:51 PM
OK to those above who said they did this ECU... no you DID not... i tested the ecu and the password is not supported by galletto... I could connect to ecu but unable to read int flash or eeprom.
You may have read TC1767.... which has been possible for a long time anyway....
Thanks...
Nio
13th June, 2013, 12:37 AM
I try to read this ecu with Fgtech2 v48 cinese clone and with no result.Make ID but not read.
Tomorrow i'll test with new Fgtech2 version 54 and post result. Regards.
Ktag read and write correctly this ecu. Regards.
enigmauk
13th June, 2013, 09:03 AM
I try to read this ecu with Fgtech2 v48 cinese clone and with no result.Make ID but not read.
Tomorrow i'll test with new Fgtech2 version 54 and post result. Regards.
Ktag read and write correctly this ecu. Regards.
I've just spoken to someone and they said that K-TAG doesn't support this ECU either...
Let me know how you get on with v54.
Thanks
mamanacusa
13th June, 2013, 11:13 AM
You got original readout over obd?
enigmauk
13th June, 2013, 07:19 PM
No i didnt do OBD.
2200
13th June, 2013, 07:36 PM
I try to read this ecu with Fgtech2 v48 cinese clone and with no result.Make ID but not read.
Tomorrow i'll test with new Fgtech2 version 54 and post result. Regards.
Ktag read and write correctly this ecu. Regards.
have you tried?
enigmauk
16th June, 2013, 01:35 AM
Nio.... did you test?/
koz
17th June, 2013, 10:38 PM
I have done many of this with FGTech 2 tool!
100% working
this ecu is currently not supported by any tool. Not CMD, not Byteshooter or FGtech ...
enigmauk
20th June, 2013, 11:45 AM
If you look from December 2012 this ecu inside the manual.... you still think its not supported?
or maybe just not supported by your clone?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.