Galletto 3 - software don't start

[Pali33]

Hello,
i bought china galletto3 and i have little problem. Software on the CD need registration code. I have downloaded software from DK, which no need the code. It is the same as i use the cracked .dll file
When i start the software (FGTech is connected to PC), it happen nothing, software not start, no error message, nothing.
FGTech USB driver is correct installed and i see it in windows device manager (WIN XP Pro 32bit).
My FGTech picture attached.
HW-ID: E1644127-D75B

Many thanks in advance!
edit: i have now the reg code and it is the same, the software don't start.
PS: my FGTech is without dongle.
201298201299

[Babos]

i think you must contac with seller and he send you eprom for galleto and when software opening.
Best regards.
Babos.

[enigmauk]

Are you using a 2.0ghz 2gb computer?

[Pali33]

Are you using a 2.0ghz 2gb computer?

i use 2.13GHz 4GB notebook (Win XP Pro 32bit show only 2,9GB ram). I have reduce the RAM (with parameter "/maxmem=2000" in file Boot.ini), WinXP show now 1.95GB ram, but it is the same, EOBD2.exe don't start, nothing happen.
I have test it on 1.5GHz 512MB notebook and here i get a error message "EOBD2.exe encountered a problem and needs to close" .

Can anybody help, what to do?

[mexanico1971]

there is no problem about the the PC requirement"s !
some people use ACER aspire ONE and it work"s !
you need to re-flash the FTDI ! ask your seller for that !
The SW without the KEY or dongle is for old version"s ! I think !

BR

[kissifur]

My galletto, arrived today and i have the same messagem in 3 pc.

[Pali33]

My galletto, arrived today and i have the same messagem in 3 pc.
is your galletto3 the same as my on the picture? My is without dongle and without usbfix on the CD. Yours too?

[2200]

double post... :hmmmm2:

[2200]

is your galletto3 the same as my on the picture? My is without dongle and without usbfix on the CD. Yours too?
where do you have buy this G3? link?
which soft do you use?

[Pali33]

yes, double post. I'm sorry. I thought that i have FGTech v51, not v53 ... here my story:
I don't have link. I bought by my supplier some ICs and i have ask him, if he can sell FGTech2. He send me picture of galletto2 3-LED version v51. I said OK, i want it. But in the parcel i found galletto 3 :-) ... without dongle.
Software seems to be the same as this crack version, just with original fgt2xx.dll (all other files are the same):
http://www.digital-kaos.co.uk/forums/f173/fgtech-galletto-v52-problem-334252/#post1952650
On the CD is no FG-FIX folder.
I'm now confused. I don't know, if is my galletto a fake, or is this a newer version without dongle ...
I found this seller:
V53 fgtech Galletto 3 Super Fgtech Galletto3 Master BDM TriCore (http://www.autodiagnosticobd.com/v53-fgtech-galletto-3-super-fgtech-galletto3-master-bdm-tricore-wholesale-auto-diagnostic-1750.html)
i have the same set, but without dongle and without OBD2 converter connector.
I will make just one test on 2GHz 1GB PC with fresh Win XP installation and with 2013.01.01 date.

Edit: i'm sorry, i don't have the same set as in link above. I have show now and i have this set:
http://m.aliexpress.com/item/587471559.html
but with galletto 3 box.

[Tuiken]

my clone came with a ma welding cable plug in the usb and software not opened. I had to open the box and weld

[kissifur]

Problem solved in mine, Work perfectly on 2 diferent pc on Windows xp sp3

[kissifur]

1. You have to set the pc date to 01.01.2013 and install drivers.
2. If EOBD.exe will not start, first try to use USB-fix, if it will not start again, do this:
go to windows control panel -> regional settings -> languages and check two checkboxes in "additional language support",
then open "advanced" tab and check all codepages.
After that click "ok" and follow windows instructions, reboot and apply usbfix once more.
You will need WinXP installation disk.
(tested on WinXP SP3 with actual updates)

[leolux]

1. You have to set the pc date to 01.01.2013 and install drivers.
2. If EOBD.exe will not start, first try to use USB-fix, if it will not start again, do this:
go to windows control panel -> regional settings -> languages and check two checkboxes in "additional language support",
then open "advanced" tab and check all codepages.
After that click "ok" and follow windows instructions, reboot and apply usbfix once more.
You will need WinXP installation disk.
(tested on WinXP SP3 with actual updates)

Do you have this new china version? FGTECH GALLETTO-2 MASTER V53 Quality A [FGA] - $189.99 : Nandtools, Auto Diagnostic Tools (http://www.nandtools.com/fgtech-galletto2-master-v53-quality-a-p-787.html)

or the old expensive v53 version? or are both the same?

Leo

[oem]

This solution working for V53. Good job! But no need to active all code page. Choose only English (United States).

[Pali33]

This solution don't work for me ... must be Galletto feed with 12V, or is enough the USB cable to start the software?

[wiski]

USB is enough

[autista]

Hii.
I have the same problem with Gallete 3.I contacted the seller, still no answers.Installation was ok.The software does not start.
Please send me a solution to this problem.Thank you in advance.

[Pali33]

in 1 week i get new hardware from the seller. Then we will see, if is hardware the reason ... i let you know.

[autista]

Thank you!I bought the www.scannerobd2.com (http://www.scanerobd2.com.(A) (a quality).
Software.
http://ulozto.cz/xeYz1j51/fgtech-galletto-3-rar

[autista]

Hii,
So I could not.I cleaned thoroughly hand registers.Software runing.Seller was willing to help.Over teamweaver.autista

[fordobd]

Try this fix I worked with the same problem


Galletto v53 fix - Downloads - Digital Kaos (http://www.digital-kaos.co.uk/forums/downloads/car-dumps-database/34/galletto-v53-fix-2577/)

[kissifur]

I have 2 pc working very good with pt-br sp3 XP, but i have other 2 PC with xp sp3 english last version and when software opens ask for activation like v48 one, anyone have the same problem?

[Pali33]

Hello,
my problem solved. I received now new hardware from china. But i received now Galletto2 (3-Led) and now work the software. The problem was as follows: i have order Galletto2, but i have received Galletto3-hardware and Galletto2-CD. This could not work. Now the software works and i will test read/write some ECUs.
... now i have Galletto3 hardware without dongle. Is any possibility to use it, or is the dongle necessary?

[mario38]

I do not own the new tool but I'm looking for a good seller and information .. I read that many problems are related to the computer's date


Attention: It is very important, please change your computer time to 2013.01.01 first ,then copy the software from CD to your computer desktop! Your computer must do not have old FGTECH software, it is very important.

I do not own the new tool but I'm looking for a good seller and information .. I read that many problems are related to the computer's date
Computer requirement: Intel Core = 2000Hz - RAM = 2.0GB

Hardware version: V53
Software version: V2012

[oem]

My clone can't read via CAN. Anybody know how to solve this problem?

[Iggie]

My clone can't read via CAN. Anybody know how to solve this problem?

I have also noticed some problems while reading over OBD through the CAN. It seems that software is making some problems. Chinese monkey business and their software packing with SenseLock. Grrrrrrrrrr.

[BATKO]

have galletto3 V53 with dongle when installed and I want to start obd2.exe to me the following window appears:
"Renewal MAKE WITH FGTech_DOWNLOAD_UPDATE TOOL FOR RE-estabilishment"

Where is the problem?

[pulsar2000]

have galletto3 V53 with dongle when installed and I want to start obd2.exe to me the following window appears:
"Renewal MAKE WITH FGTech_DOWNLOAD_UPDATE TOOL FOR RE-estabilishment"

Where is the problem?

and your pc bios date 1-1-13 ?

[BATKO]

and your pc bios date 1-1-13 ?
Change date in BIOS and report!

[BATKO]

Change date in BIOS and report!
Bios have date 01.01.2013...i need to reflash firmware, where find?