PDA

View Full Version : Problem reading ASTRA H turbo 7.6.2



ruffles1986
29th June, 2013, 10:29 PM
Hello i try to read ecu of opel Astra H 2.0 turbo Bosch 7.6.2 with MPPS V12 and the read stop at 75%. I read about this ecu have problem to read, but can write without problems...
I look for driver on FGTECH V52 for try to read with this tool, but don't exist.

Any can help me to remap this ecu?

Thanks!

ruffles1986
30th June, 2013, 10:46 AM
Anyone can help me??

ominimicu
30th June, 2013, 03:16 PM
dont you have that ecu under Opel agila?

ruffles1986
30th June, 2013, 05:01 PM
dont you have that ecu under Opel agila?

Yes m8 i see it now,the ecu is the same, i try to read with FGTECH tool and report result.

Very thanks ominimicu (http://www.digital-kaos.co.uk/forums/members/133668-ominimicu/) for help me with alls my doubts. really thanks

flixuno
30th June, 2013, 05:10 PM
hi!
test directly in the bank
with mpps

flixuno
30th June, 2013, 05:28 PM
hi!
connector T2

pin 18 and 51................ positive 12 v
pin 43 .........................can h
pin11...........................can l
pin 5............................gnd

ominimicu
30th June, 2013, 06:29 PM
ok read and post, i beleive the file is a bit small than 1 mb

Gibon14
30th June, 2013, 06:41 PM
You can try with zafira turbo 7.6.2. It works fine.

Shaheenem
1st July, 2013, 03:21 PM
MPPS always gave me a problem. I used Fgtech mini EURO clone with Agila protocol and works perfect for me.

ruffles1986
3rd July, 2013, 10:57 PM
Today i try to read ecu 7.6.2 from opel astra h 2.0 turbo Z30LER 200Cv with FGTECH clone v52 selecting Opel Agila 1.2, same ecu and send error message, the fuel pump begin to sound hard for moments and then stop. Can any share picture with pinout for this ecu??
Thanks

lewich
3rd July, 2013, 11:41 PM
Hello,

I have read and written many Astra 2.0T's with the 7.6.2, always works perfectly. I have a genuine tool though. Try reading under Corsa 1.2 7.6.2, although I doubt that would make much difference. What year is the car?

lewich
3rd July, 2013, 11:43 PM
I have the pinout diagram you need also, let me know.

ruffles1986
6th July, 2013, 01:04 AM
I have the pinout diagram you need also, let me know.

i try to read with fgtech clone and don't work, please share pinout

Faboka
7th July, 2013, 05:37 PM
I've been having a similar issue.

Trying to read a 2008 astra h vxr using MPPS V12. Get to 65% then it fails.

Dobermann
2nd October, 2013, 05:26 PM
I've been having a similar issue.

Trying to read a 2008 astra h vxr using MPPS V12. Get to 65% then it fails.


same problem with my MPPS V16 read stops at 65 %

my galletto clone reads file but worng file size ! G2 reads 832kb
the galletto have not the right driver for the me7.6.2 turbo

i read it with my optican file size is 768 kb file ok but long read out time 40 min.

alclot
31st October, 2014, 10:02 AM
Hi flixuno. I'm trying to connect with a Bosch 0261 208 254 / ME 7.6.2 but does not connect.
It is the only one that I could not connect. I've always been able to do. The car is a Agila 1.2 year 2006. do you know which is pin the K line to try? CAN-BUS not work.
I try with two ecus same reference with fgtech2, advi, ... but no work.
Thanks in advance ;)


hi!
connector T2

pin 18 and 51................ positive 12 v
pin 43 .........................can h
pin11...........................can l
pin 5............................gnd

motorsportsz
31st October, 2014, 07:21 PM
I managed to read this ecu under Opel agila quite a while ago. Read and wrote perfect via obd

alclot
3rd November, 2014, 08:18 AM
Did you use the same pinout? I tried with two equal ECU not connected. Instead, I try another ecu from the same family and connect perfectly in workbench.


I managed to read this ecu under Opel agila quite a while ago. Read and wrote perfect via obd

motorsportsz
24th January, 2015, 10:12 AM
Did you use the same pinout? I tried with two equal ECU not connected. Instead, I try another ecu from the same family and connect perfectly in workbench.

I done it obd mate