PDA

View Full Version : KESS V2 CLON READ DME MSV80.0 BMW 125



michalik
12th August, 2013, 04:32 PM
HELLO, CAN SOMEONE CHECK IF THIS FILE IS WELL READ AND IF APPLICABLE TO THIS ECU?
HE USED, KESS V2 TOOL. CLONE

BMW 125 218HP
TRANSMITION AUTOMATIC
ENGINE CODE : N52B30AE
THANK YOU HOPE YOUR HELP.

moky
12th August, 2013, 05:50 PM
if it's an MSV80 you can read but i think you will have problem for write it with fgtech or kess...

michalik
12th August, 2013, 05:58 PM
I am using KESS V2 CLONE interface.
also problems in writing?
thanks for your reply.

OVERSPEED
12th August, 2013, 06:00 PM
MSV70 - Fgtech euroclone didn?t write: error erase Flash and car didnt?start... sabe original fiel and works again...

moky
12th August, 2013, 06:00 PM
i think yes,it can read and write MSD80 and MSV80 just read,you can see that msv not on list car so be careful at flash.fgtech read it too but no flash

carmageddon
12th August, 2013, 06:35 PM
213657

if interest, i do this ecu with fgtech2 v48 via obd without problem, 30 min read, 30 min write.

michalik
12th August, 2013, 10:55 PM
BOOT MODE IS POSSIBLE IN THIS ECU?
ALGUIEN LO HA INTENTADO?
THANKS

atomiczen
12th August, 2013, 11:16 PM
already flashed with kess v2 clone both msv80 and msd80 read and write ok

michalik
13th August, 2013, 01:31 PM
There is no way to recover in case of bad writing?


excuse me but, I'm trying to clear all the doubts, to avoid serious problems.

thanks.

J_amb_o
13th August, 2013, 03:04 PM
213657

if interest, i do this ecu with fgtech2 v48 via obd without problem, 30 min read, 30 min write.

MSD80 K line?

carmageddon
13th August, 2013, 05:49 PM
now i dont remember if K or can

J_amb_o
13th August, 2013, 08:32 PM
It's K line normally, and V48 struggles with that.

HsamehH
14th August, 2013, 11:20 AM
with fgtech euro clone write failed for E92 M3 i had to write ecu on bench out of car.

carmageddon
14th August, 2013, 01:07 PM
It's K line normally, and V48 struggles with that.

i dont have problem to do this ecu.

OVERSPEED
14th August, 2013, 03:45 PM
with fgtech euro clone write failed for E92 M3 i had to write ecu on bench out of car.

Wich ECU ? MSV70 ?

michalik
15th August, 2013, 01:02 PM
friends ...
to think I will not do this writing via obd ECU.
many risks and no way to recover the ECU.
if anyone knows how to read this ecu in bootmode tricore (tc sak 1796).
please tell me how to do it.
thank you all ..

J_amb_o
15th August, 2013, 08:48 PM
Not possible. OBD only.

dudus8
23rd July, 2019, 09:49 AM
Hello,
I have a question:
Ecu from E90 LCI 318i N43 probably MSD80 possible read and write with Kess clone by obd?

spacie2136
23rd July, 2019, 12:34 PM
No problem with actual tools (KessV2 / galetto / clone) and battery charger connected ;-)

dudus8
23rd July, 2019, 04:01 PM
No problem with actual tools (KessV2 / galetto / clone) and battery charger connected ;-)


OK. Thanks for info.
I have only simple charger Bosch C7, will be good for this read and write?
How many time read/write for MSD80-81 ecu?

spacie2136
23rd July, 2019, 07:10 PM
Be Sure that you have more than 12.4 volt when you write back. I'm not sure how long it takes.

Lambda1
2nd October, 2019, 10:43 AM
via obd ~30min.
Would use better ~13,8v and good power supply... or do it on bench .