PDA

View Full Version : Fgtech v53 repair



morgano
12th August, 2013, 05:36 PM
Hi.

My fgtech v53 china clone does not work on J1850 PWM to read FORD focus with visteon ecu, cannot even ID the ecu, i have replaced both max481csa without luck, any clue about what to look next will be welcomed.

Thanks

morgano
13th August, 2013, 01:02 PM
Anyone??

Please, just a clue...

BrunoPT
13th August, 2013, 03:28 PM
Anyone??

Please, just a clue...

Fgtech 3 leds?

morgano
13th August, 2013, 03:57 PM
Well, it really has 3 leds :) but i am talking about fgtech v53 new hardware, nos same as v48,50,51 either 1 or 3 leds.

It is china clone fgtech v53 with jtag hw etc ...

BrunoPT
13th August, 2013, 04:02 PM
I've had galletto with LED and 3 LEDs
The 1 led, well-read and record in Visteon away in the end gave an error, but took car and worked well.
In 3 leds never even got to read these drives, just gave error at the beginning.
I filled myself and bought a Power Gate, problems solved :)


Sorry I can not help more.


greetings,

vasco fernandes
13th August, 2013, 08:45 PM
fgtech v53 is 2 led, right ?

morgano
13th August, 2013, 09:32 PM
2 led to show communication progress and 1 led at the side to show power is connected.

morgano
13th August, 2013, 10:01 PM
Here High Res Photo of the PCB.

J_amb_o
13th August, 2013, 10:47 PM
Clone does not with with PWM

morgano
13th August, 2013, 10:53 PM
And you know why? ;)

J_amb_o
13th August, 2013, 11:13 PM
Separate chip, which is not active. Same as with Powergate clones, don't work on PWM.

morgano
13th August, 2013, 11:50 PM
Sorry, can't understand what you mean.

You want to say the max481 are present on the circuit but are not connected to MCU and or DB15 pins? There's nothing more involving PWM, isn't it?

Thanks

veloseeped
13th August, 2013, 11:52 PM
About J1850 in old G2...

morgano
14th August, 2013, 12:50 AM
Sure J1850 circuit have changed since old fgtech v48.

From DB15 both involved pins go to respective transistors, then to something like a 74hc14 throw another transistor... bla bla

Also pins from MAX481 that should go to MCU go throw another set of what seems to be another 74hc14. Seems to me there are 5 74hc14 in this new hw, not 3 like the older.

Here is my guess on V53.

Red circled and blue circled ICs = 74hc14
Yellow circled = hef40106bt
Pink circled = Max481
Green circled = Can Gateway 82c250 (if i remember well).

Other Ics are unknown yet, only the DC-DC converters that should be mc34063a like older hw.

Regards

morgano
14th August, 2013, 07:44 PM
Separate chip, which is not active. Same as with Powergate clones, don't work on PWM.

Maybe just a wire may become the inactive chip in active one? ;)

eiemax
14th August, 2013, 10:56 PM
In black "circle" are 2: ST L9637D
Black point on the IC is the N?1 pin

eiemax
15th August, 2013, 01:04 AM
In "circle" Brown color, are left:
1117CS
3.3

and are at right:

1117CS
1.8

eiemax
15th August, 2013, 01:42 AM
In grey colos is:

FTDI
FT232RL
(Incorporating clock generator)

eiemax
15th August, 2013, 02:32 AM
Sure J1850 circuit have changed since old fgtech v48.

From DB15 both involved pins go to respective transistors, then to something like a 74hc14 throw another transistor... bla bla

Also pins from MAX481 that should go to MCU go throw another set of what seems to be another 74hc14. Seems to me there are 5 74hc14 in this new hw, not 3 like the older.

Here is my guess on V53.

Red circled and blue circled ICs = 74hc14
Yellow circled = hef40106bt
Pink circled = Max481
Green circled = Can Gateway 82c250 (if i remember well).

Other Ics are unknown yet, only the DC-DC converters that should be mc34063a like older hw.

Regards

Hi friend, where is the DC-DC converter (IC: mc34063a)?

Thanks

oem
15th August, 2013, 07:20 AM
Where is the Green circled?

eiemax
15th August, 2013, 09:36 AM
Where is the Green circled?

to the left of the relay black

morgano
15th August, 2013, 12:26 PM
Hi friend, where is the DC-DC converter (IC: mc34063a)?

Thanks

I supposed they were the two 8pin ics just behind the power jack and next to the electrolitic capacitors. But it seems not. ;)

mexanico1971
15th August, 2013, 06:45 PM
Maybe just a wire may become the inactive chip in active one? ;)

in what cars ECU"s, do you try you tool and it work ?!

Br

morgano
16th August, 2013, 02:43 AM
Just tried on mine TDdi FORD and not working, kline on edc15c2 worked fine. No further tests.

foxtec800
16th August, 2013, 07:10 AM
mine doesn`t work for k-line does anyone know the common fault ?

morgano
16th August, 2013, 10:31 AM
I don't really know if china v53 has flaw desing and they missed linking some parts to the circuit as Jambo suggest, but i think scratching the ICs so hard to remove labeling may damage some of them, and that is why we see strange faults like that kline fault. When mine seems to work flawlessly on kline.

eiemax
16th August, 2013, 10:42 AM
I don't really know if china v53 has flaw desing and they missed linking some parts to the circuit as Jambo suggest, but i think scratching the ICs so hard to remove labeling may damage some of them, and that is why we see strange faults like that kline fault. When mine seems to work flawlessly on kline.

I agree with you, for this I would like to know what are the chips that are in the circuit, so I can replace those that do not work.

bmw320d
17th August, 2013, 09:16 PM
Hi I have tried this interface, on edc16c39 fiat and not work stop reading at 40%, on fiat 500 1.3 mjet 6F3 not read ecu, perhaps an error on canbus or chip canbus, old interface v50 runo ok in this ecu, tried on more edc16, marelli 6f3 on edc17 vag opel and edc15

giuseppe1374
21st August, 2013, 06:51 PM
I believe that this photo will be helpful
215252

gezame
22nd August, 2013, 12:08 AM
I've had galletto with LED and 3 LEDs
The 1 led, well-read and record in Visteon away in the end gave an error, but took car and worked well.
In 3 leds never even got to read these drives, just gave error at the beginning.
I filled myself and bought a Power Gate, problems solved :)


Sorry I can not help more.


greetings,

Hi
Galletto with 3 LEDs works perfectly in K-line, only need change one resistor.
Br.

eiemax
22nd August, 2013, 12:45 AM
which resistor friend? You can tell?

giuseppe1374
30th August, 2013, 12:42 PM
all pictures as possible, I think it is a nice thing
if you can please give a thank you, thank you
216798216799216801216805216806

giuseppe1374
30th August, 2013, 12:44 PM
216807216808216809216810216811

giuseppe1374
30th August, 2013, 12:46 PM
216812216813216814216815216817

weekdgl
1st September, 2013, 02:47 PM
thanks!! it's made in eu clone or original?

morgano
2nd September, 2013, 12:28 AM
Thanks for all photos, but...

Anyone knows how to repair to make FORD PWM working?

megasosio
8th September, 2013, 04:00 PM
Hi!! looking china clone and comparing whit eu clone y see two diferences at first sight.

1- missing one led near power led. I put them and switch on when plug on usb.

2- missing one capacitator near U15. I like to know what its the correct because it can be the *wire to connect to solve de pwn fail*??


218351

eiemax
8th September, 2013, 05:13 PM
what is the value of this capacitor?

morgano
9th September, 2013, 09:57 AM
Hi!! looking china clone and comparing whit eu clone y see two diferences at first sight.

1- missing one led near power led. I put them and switch on when plug on usb.

2- missing one capacitator near U15. I like to know what its the correct because it can be the *wire to connect to solve de pwn fail*??


218351

Definetly this is something worth checking. Thanks ;) Let's see if someone knows capacitor value.

I saw also another photo, can't rememer where now, but i think there is another missing component. This one...

218427

It's possible we are going in the right direction...

Regards,

megasosio
9th September, 2013, 10:10 AM
MORGANO

Yes this component its missing but in eu clone too , for this i no talk about it.
The most important i think its to know the value of capacitator.

morgano
10th September, 2013, 01:26 AM
Tomorrow will try to desolder one of the capacitors in the same circuit and measure it.

eiemax
10th September, 2013, 07:44 AM
Tomorrow will try to desolder one of the capacitors in the same circuit and measure it.

Good friend... :top:

morgano
10th September, 2013, 10:01 PM
if i'm not mistaken and made good measurement, the capacitors are 10pF ;)

eiemax
10th September, 2013, 11:53 PM
if i'm not mistaken and made good measurement, the capacitors are 10pF ;)

Good friend, and now just have to try

morgano
11th September, 2013, 03:26 PM
Must find another 10pF capacitor in a scrap pcb to fit in fgtech, then i can test in my own focus TDdi.


Regards,

morgano
11th September, 2013, 04:30 PM
Just tested, and result is.....


.... no luck, China V53 still can't talk with my ford focus, even cannot ID the visteon shit.

There's another point where the problem should be. Time to continue looking for it.

ishell
11th September, 2013, 05:27 PM
I need to know output voltage from pin 1 U5 and U6 ( LP2915 ic) . I see my V53 have U5 -11,6 V and U6 have 6.6 V.Strange voltage from regulators.

morgano
11th September, 2013, 05:53 PM
Well, more news...

Just made an experiment, removed transistors (white crossed in the photo) and made (the red) bridges just to make the circuit as closer as possible to the V48 that worked fine on PWM. Here's photo with changes.

218871

... and guess what.... I can now ID the ECU sucessfully. Communication is back. :) But.... (yes, there is always a BUT) the ecu doesn't enter programming mode to read or write to it. :( I think is missing programming voltage in some pin of the OBD plug and the circuit skipped with this mod should be in any way responsible of it.

Come on, we are getting closer. More ideas? :)

Regards,

morgano
11th September, 2013, 08:57 PM
I need to know output voltage from pin 1 U5 and U6 ( LP2915 ic) . I see my V53 have U5 -11,6 V and U6 have 6.6 V.Strange voltage from regulators.

My U5 output in pin 1 is 12.09V and U6 is 6.70V.

Does annybody know the name of the two transistors i removed (Q18 & Q20)? Are both same?

megasosio
12th September, 2013, 06:54 PM
In my u5 pin 1 is 11.96 and in u6 pin 1 is 6.57 .

Up!!!

morgano
12th September, 2013, 07:01 PM
What are transistors numbers? Anybody knows???

Are both same transistors or are different?


Regards,

eiemax
12th September, 2013, 07:13 PM
Sorry friend, but I do not know what is the name of these transistors.

megasosio
12th September, 2013, 07:25 PM
I have one galletto v53 whit all pics ok and u5 and u6 are lp295 (87rd-lp295-1acm). I test the second v53 and the same voltage. and i test q20 and q18 and input 6.55v in two gall v53.

morgano
12th September, 2013, 09:25 PM
I ask the two transistors i removed to make pwm work again. The two just behind the db15 plug, in TO encapsulation not smd.


Regards,

morgano
12th September, 2013, 09:49 PM
@megasosio

Which numbers you read on Q18 & Q20?




Regards,

megasosio
13th September, 2013, 09:50 AM
q20 and q18 are zvp-2106-a

istvanp
13th September, 2013, 01:43 PM
ZVP 2106 A - Zetex P-Channel Mosfet , E-Line bei reichelt elektronik (http://www.reichelt.de/ZETEX-Transistoren/ZVP-2106-A/3//index.html?ACTION=3&GROUPID=2905&ARTICLE=68635&SHOW=1&START=0&OFFSET=16&)

eddieddi
13th September, 2013, 05:37 PM
@ megasosio
Can you check the name of transistor Q1 please ?
THX

megasosio
13th September, 2013, 06:42 PM
Q1= bc337-25

eddieddi
13th September, 2013, 06:56 PM
Thank you !
I have used the same for replace :-)

morgano
13th September, 2013, 10:18 PM
hmmm, i have tried to measure the FETs i removed, and for sure they are not the same type. One have S and D pins reversed regarding the other. and acts different on exciting the G. Are you sure both FET are same ZVP2106A? These FET are in a EU clone with working PWM?

morgano
14th September, 2013, 02:50 PM
@eddieddi

Clear your inbox, it is full ;)


Regards,

megasosio
15th September, 2013, 09:11 AM
I find another resistance that are in eu Clone and no in china clone. Its near obd conector and is 4k7!!!! Please test in Ford @MORGANO.


Enviado desde mi VilleDroid V2.3 usando Tapatalk 2

morgano
15th September, 2013, 09:44 AM
There are 2 missing components near db15 connector, one is just at the side of the relay and the other one a bit farer near lm393 i already tesded 472 resistor near relay and makes no difference. Maybe you mean the one at the side of pin7 lm393?

Please post photo ;)


Regards,

megasosio
15th September, 2013, 09:51 AM
Attached a photo of missisng part.

morgano
15th September, 2013, 11:41 AM
@megasosio

Already tried fitting that 4k7 made no difference on my ford, still no comms on PWM.


Regards,

megasosio
15th September, 2013, 11:56 AM
I try to make a list of all resistences and
Componente differents on china clone. All the problem must be perturbation on pwm comm ir missing voltage. You know what pins make comm in pwm Ford?? And when se know what are involved i follow the connections in Clone to trt to know how it Works and what must be the regulations.

morgano
15th September, 2013, 02:49 PM
Pins 2 & 10 are the ones involved in ford j1850 pwm, and go in first instance from the same number db15 pins directly to the q18 & q20 transistors.


Regards,

morgano
18th September, 2013, 08:21 PM
Any more news on this? Anyone tested the transistor removal mod and works for him too?

megasosio
19th September, 2013, 01:21 PM
I added the led, resistance, condensator and in bdm works flawesly. Before this mod bdm fails most time. I need to try whit a ford but i havent one to test near....

If someome have another test please report here!!!

I have galletto v54 eu soft and i installed sucesfully bypassing dongle protect, and whats my surprise its the same that v53 chineese!!!! nothing changes, only added 1.exe that run whit dongle. EOBD2.exe its the same as chineese. Only change the serial of interface because when i run it run but not detect interface serial.
If someone have v54 eu clone whit dongle please upload ftdi read to test the chineese clone.

Sorry if i make bad whit eu clone sellers... sorry

zecas
19th September, 2013, 02:02 PM
I added the led, resistance, condensator and in bdm works flawesly. Before this mod bdm fails most time. I need to try whit a ford but i havent one to test near....

If someome have another test please report here!!!

I have galletto v54 eu soft and i installed sucesfully bypassing dongle protect, and whats my surprise its the same that v53 chineese!!!! nothing changes, only added 1.exe that run whit dongle. EOBD2.exe its the same as chineese. Only change the serial of interface because when i run it run but not detect interface serial.
If someone have v54 eu clone whit dongle please upload ftdi read to test the chineese clone.

Sorry if i make bad whit eu clone sellers... sorry

good work please tell us does the eu software need to put date back to 1/1/13 and ad language in regional settings?

megasosio
19th September, 2013, 02:16 PM
Yes it needs because to run it need dongle and run another exe, not eobd2.exe but if i run eobd2.exe need to time but not regional language, and works ok in any computer whithout install nothing extra, only run.

I think the protected .exe is a fix for time and other requeriments. Like if it put another hardware id in pc to eobd2.exe like if it run in dell d630. Its only a suposition.... im not a cracker...

zecas
19th September, 2013, 02:26 PM
is it possible to share this eu software or just the eobd2.exe to play and try to get serial number from it

in older version like v1 you could see serial number in exe with editor and change it

megasosio
19th September, 2013, 02:34 PM
Here the eobd.exe . How i can see the serial number to change it on exe???? maybe it works ok!!! The all rest of files are the same on chineese.
220238

zecas
19th September, 2013, 02:52 PM
on this one it is not possible without having the source code
better waith if some member can share the ftdi template for this exe

morgano
19th September, 2013, 03:44 PM
Not so easy, the exe is packed and many of the interesting code runs on realtime in a protected virtual machine.




Regards,

allent
20th September, 2013, 12:37 PM
problem with changing the date of system you can solve by RunAsDate software(works 100%) problem with dongle you can solve by changing wibu.dll, but you have to install additional languages ***8203;***8203;in os you are using. i am talk about china clone

gezame
21st September, 2013, 12:14 AM
I added the led, resistance, condensator and in bdm works flawesly. Before this mod bdm fails most time. I need to try whit a ford but i havent one to test near....

If someome have another test please report here!!!

I have galletto v54 eu soft and i installed sucesfully bypassing dongle protect, and whats my surprise its the same that v53 chineese!!!! nothing changes, only added 1.exe that run whit dongle. EOBD2.exe its the same as chineese. Only change the serial of interface because when i run it run but not detect interface serial.
If someone have v54 eu clone whit dongle please upload ftdi read to test the chineese clone.

Sorry if i make bad whit eu clone sellers... sorry

Hi
You software fgtech V54 eu-clone, can read-write eeprom simos PCR, or only unlocked?

oem
21st September, 2013, 05:19 PM
I have onlt 4.6 volt on pin3 from can trasmitter 82c250.Anybody know who is the controlling input voltage?

bmw320d
21st September, 2013, 05:36 PM
I have onlt 4.6 volt on pin3 from can trasmitter 82c250.Anybody know who is the controlling input voltage?

Hi the pin 3 is the voltage (power supply) of can transmitter, the range is from 4.5v to 5.5v, my interface not recognize can ecu and has problem reading ecu in canbus

oem
21st September, 2013, 07:42 PM
same problem in my interface :)

fabiof1
23rd September, 2013, 10:36 PM
Hello.


I have the v54 galletto.
I want to know how to copy the dump lpc2119 to put on another v53 version?


Turning 53 in a version v54.


I have a second Chinese v53 galletto does not work.


Thank you

megasosio
23rd September, 2013, 10:50 PM
Try to talk whit bootloader to see if is original of nxp mcu. If is original nxp bootloader can make a dump of lp2119 an put in another mcu. This is in a very short words the process to reverse ing the mcu.
To tras that mcu j-Link v8 its good and cheapest. I have one but i dont have the knowledge to make the process, if aomeone can help us, i put here the fw54 free for all because this Forum help me tooooooo much to learn about this world.

Sorry for My bad english.

fabiof1
24th September, 2013, 05:36 AM
I do not understand everything.
But Mprog or other software that is not possible to copy the dump ...

megasosio
24th September, 2013, 09:03 AM
Mprog is for ftdi. We need to dump de mcu, lp2119 and read with a special programmer like j-Link. And this mcu is protected, and the other way to make a dump is trought a hole in bootloader. a hole maybe can be the bootloader if still original nxp.

Isnt easy but not impossible.

fabiof1
24th September, 2013, 09:58 AM
With jlink is possible.
Must be unsoldered???

veloseeped
24th September, 2013, 09:58 AM
lp2119 and read with a special programmer like j-Link. And this mcu is protected, and the other way to make a dump is trought a hole in bootloader. a hole maybe can be the bootloader if still original nxp.

Isnt easy but not impossible.

Tested with JLINK over jtag and bootmode - both ways to read dump are disabled in 2119 firmware.

fabiof1
24th September, 2013, 10:32 AM
Ok you can not find the dump on the net ...


Because if it is protected it is hard.

q-zar
25th September, 2013, 03:15 AM
hi veloseeped .need pass thanks you. how to upgrade v50 old to v53 new hardware.interesed delpfi mersedes for can bus read.

morgano
25th September, 2013, 08:13 AM
Please guys, come back to the repair topic.

We are looking here how to repair v53 new hardware faults, not how to upgrade old hw to new which is impossible.



Regards,

AlexandruP
25th September, 2013, 11:36 AM
Hi
You software fgtech V54 eu-clone, can read-write eeprom simos PCR, or only unlocked?

I have eu clone with PCR unlock via EEPROM working perfect and then read/write by OBD. I have test working on maybe 8 or 9 cars total now. I'm also testing JTAG and RENESAS works good!

gezame
26th September, 2013, 01:43 AM
Hi
I think software for V54 euro clon, only option for eeprom unlock simos pcr.
Software for V53 chinese, option read-write-unloock eeprom.
Br.

2200
9th October, 2013, 07:03 PM
euro V54

fixed..

RicardoJvCruz
22nd October, 2013, 12:36 AM
2200 i've tried the missing 4k7 resistor and 10pf capacitor in v53 china, still cannot read edc16 only can get correct ID.

Have some clue ?

Thank you

2200
22nd October, 2013, 05:50 AM
2200 i've tried the missing 4k7 resistor and 10pf capacitor in v53 china, still cannot read edc16 only can get correct ID.

Have some clue ?

Thank you

it is other problem for kline edc16 :-)

RicardoJvCruz
22nd October, 2013, 01:33 PM
I will give up of this chinese shit v53 :s

I don't trust in interface anymore, just looking for kess v2..

Thank you 2200.

RicardoJvCruz
22nd October, 2013, 01:55 PM
I will give up of this chinese shit v53 :s

I don't trust in interface anymore, just looking for kess v2..

Thank you 2200.

serdarmsc
22nd October, 2013, 02:25 PM
don't believe v54, it's v53. i will write solution for k-line. now continues to test...

RicardoJvCruz
22nd October, 2013, 03:04 PM
@serdarmsc thank you for helping fixing the k-line of v53 china.

I will wait for some better news :)

Thank you

serdarmsc
22nd October, 2013, 06:32 PM
opel combo 1.3 multijet marelli ecu : id/read/write OK

225978

i will add all tested ecu pictures.

eiemax
22nd October, 2013, 09:57 PM
Hello friend, you can share the solution for kline? I can do some tests.
thanks

RicardoJvCruz
22nd October, 2013, 10:44 PM
hey good work @serdarmsc :top:

you changed a lot of pieces ?

serdarmsc
22nd October, 2013, 11:09 PM
yes, some ic and resistors changed. bdm work fine.

RicardoJvCruz
22nd October, 2013, 11:33 PM
@serdarmsc and obd kline with edc16 is working ?

eiemax
22nd October, 2013, 11:59 PM
Hello friend, you can share the solution?
Thanks

oem
24th October, 2013, 09:37 AM
You can't make V53 china crap working well because the problem is in firmware. I replace all elements which i see from my Eu clone without success. Working well on K-line, tricore, bdm. Can't read via CAN edc16.

Software V53 and V54 is the same.

RicardoJvCruz
24th October, 2013, 12:23 PM
@oem with v53 i can read edc16 via CAN but it takes to mutch time, each 3% takes 4 minutes.

i will return my interface to seller..

serdarmsc
24th October, 2013, 12:26 PM
it's not can or mcu problem. it's only k-line problem. maybe your device different.

oem
24th October, 2013, 12:36 PM
my china clone is from ecutool quality A with two LED.

If connect ECU edc16/edc17 on the bench via tricore cable direct on ecu pins. When i choose TOOL boot (only power and can H/L are connected) i can read ID and flash. But when i choose Car and try to get ID or read i can't.

RicardoJvCruz
24th October, 2013, 12:50 PM
oem my v53 china clone are from obgiigroup.com (new site of nandtools.com).

I cannot read edc16 via kline only can get ID.
Super slow read in CAN mode i give up aborting read because it should take an hour lol
I think after i put 4k7 resistor i would able to read edc16 via CAN but it takes forever.

MARELI MJET 1.3 Opel i always can read and write via OBD with no modifications.

serdarmsc
24th October, 2013, 02:06 PM
MARELI MJET 1.3 Opel i always can read and write via OBD with no modifications. me too. CAN is perfect and better than v48. ;)

RicardoJvCruz
24th October, 2013, 02:12 PM
yes but edc16 can it's another story heheh

oem
24th October, 2013, 02:32 PM
also edc17 OBD.

serdarmsc
24th October, 2013, 07:47 PM
Delco LVP11 kline id/read/write OK.

i will try bosch edc series.

RicardoJvCruz
25th October, 2013, 03:49 AM
@serdarmsc good luck with edc series :)

serdarmsc
25th October, 2013, 06:10 AM
i am try 3 pcs edc series before the revision. Hyundai Getz 1.5 Crdi EDC16 = no id /// Hyundai Accent 1.5 Crdi EDC16 = id but no read /// Fiat Bravo 1.6 Mjet ECU EDC16+C39 = id and %20 Read. So its not mcu problem. i can fix it, i believe :)

oem
25th October, 2013, 06:44 AM
This cars read/write via k-line. Not CAN. My china interface working well on K-line :)

serdarmsc
25th October, 2013, 09:14 AM
Do you send PCB pictures? maybe your PCA82C250 kaput :)

oem
25th October, 2013, 11:31 AM
I gave new one 82c250 and will change and test again.

serdarmsc
25th October, 2013, 11:59 AM
You can try TJA1050

serdarmsc
25th October, 2013, 04:25 PM
http://img.tapatalk.com/d/13/10/25/ynutaveq.jpg

Edc16c34 can ok


Sent from my iPhone using Tapatalk

RicardoJvCruz
25th October, 2013, 09:49 PM
serdarmsc it will only remain the mcu in board ?

My tests in edc16 was in edc16u1 VAG.

2200
25th October, 2013, 10:02 PM
serdarmsc it will only remain the mcu in board ?

My tests in edc16 was in edc16u1 VAG.

edc16u1 is k-line no problem to fix it.

sumi1
3rd November, 2013, 07:04 PM
I have a V53 clone Galletto china I tested Marelli Citroen 6lpf and VW polo EDC15 obd read ok.I have problems with BDM, I can not open program.I think it's software problem but I can not turn on the BDM





227966

vasco fernandes
5th November, 2013, 01:08 AM
Is easy repair BDM this v53 ?

sumi1
5th November, 2013, 09:10 AM
problem is I can not open program



http://www.youtube.com/watch?v=ZiH42gfyWRI&feature=youtu.be

RicardoJvCruz
7th November, 2013, 12:11 AM
Thanks @2200 for helping me with my v53 china troubles :)
It was like a bless to the interface :)

2200
7th November, 2013, 06:21 PM
no problem :-)

lagas
7th November, 2013, 09:05 PM
Hi guys, do you all use chine winxp, and all install staff, any chance install to normal winxp sp3?

Saulius Saulius
7th November, 2013, 09:52 PM
Hi guys, do you all use chine winxp, and all install staff, any chance install to normal winxp sp3?
I use normal win xp sp3, everything works perfect.

psico
8th November, 2013, 10:44 PM
Please any send fix for v53?
thanks.

rdkw
18th November, 2013, 02:20 AM
its possible to china clone can-bus work ?

bubu55
19th November, 2013, 07:17 PM
Has anyone solved the problem of edc16 c39 in china clone?

The solution seems to be to change the pull up resistors 270 ohm to 200 ohm.
Can anyone point in the picture where are the pull up resistors from 270 ohms?

serdarmsc
19th November, 2013, 08:20 PM
red marked 270ohm, but 200ohm wrong because you need ~500-600ohm for edc16c39. Solution different, maybe wrong.

fsvsunix
25th November, 2013, 03:29 PM
And here is the fix for the crashing bug after a bad date installation.

http://www.digital-kaos.co.uk/forums/f173/fgtech-galletto-2-master-v53-318319/index15.html

dottecu
1st December, 2013, 11:32 AM
Hi friends ,I have 1 Fgtech v53 but not work line can! I can read cars whit k-line but not can do id or read cars whit can-line! Who know component for repair tool? Regard Alex

eiemax
10th December, 2013, 12:21 PM
Hi friends ,I have 1 Fgtech v53 but not work line can! I can read cars whit k-line but not can do id or read cars whit can-line! Who know component for repair tool? Regard Alex

I have the same problem. K-line and BDM all ok, but CAN line, not work. is there any solution to this problem?
Thanks

2200
10th December, 2013, 10:12 PM
if no can ecu work than change mcu....

eiemax
10th December, 2013, 10:29 PM
you can find a new MCU?

Marmes
11th December, 2013, 02:10 PM
I can get mcu

eiemax
11th December, 2013, 08:30 PM
Ok friend, can you tell me how to do?
thanks

Marmes
11th December, 2013, 11:36 PM
You need to buy it programmed already.

2200
12th December, 2013, 12:31 PM
I have just v54 mcu

eiemax
12th December, 2013, 01:02 PM
I can put it in my v53 clone?

Marmes
12th December, 2013, 01:36 PM
Yes you can, I did it already :)

2200
12th December, 2013, 08:40 PM
yes, and you can use better soft witout dongle, and no problems with date

eiemax
12th December, 2013, 09:02 PM
it is sufficient to only change the MCU or you must also replace the ftdi?

2200
12th December, 2013, 09:13 PM
ftdi no need will work

Marmes
12th December, 2013, 09:17 PM
You need to replace both, if you want it working as original.
The replacement I got, doesn't use patches, keygens , changed dates or loaders. Just runs with any date any windows (xp and 7)

eiemax
12th December, 2013, 09:31 PM
so the best thing is to replace MCU and ftdi?

Marmes
13th December, 2013, 12:00 AM
so the best thing is to replace MCU and ftdi?

Yes that is the best way. because is the way the original works.

lagas
13th December, 2013, 12:22 AM
There i can get mcu, please any detales in pm. Thanks

eiemax
13th December, 2013, 01:03 AM
Mcu and ftdi?

Multipla
13th December, 2013, 06:46 AM
How can I do repair galletto2 to read in boot mode? I dont read a Iaw 5sf8 with processor ST 10f296. Many tanks in advance.

Multipla
13th December, 2013, 06:47 AM
How can I do repair galletto2 to read in boot mode? I dont read a Iaw 5sf8 with processor ST 10f296. Many tanks in advance. MY galletto is 84-103 black_box 3 led.

Marmes
13th December, 2013, 01:31 PM
How can I do repair galletto2 to read in boot mode? I dont read a Iaw 5sf8 with processor ST 10f296. Many tanks in advance. MY galletto is 84-103 black_box 3 led.
You must see if your K line is working and your software can do it. If both are ok, all you need is to follow instructions. For ST processors, Piasini is a better tool.
Regards!

OVERSPEED
13th December, 2013, 03:33 PM
Sometimes You have to Guess... yesterday tried an old Marea 2,4 160cv petrol with ME3.1:

MPPS read it fine (had made it before) in car and bench
1260 with protocol 7.2.1 worked, but had a "gap" in between EFFF and FFFF (or something like this) that contained only "FF" (other protocols didn?t read anything, just "00" or crap)
V53 portuguese tool didn?t worked (all "00" or crap reading)

tried V53 with generic ME7 512Kb boot and read fine.

ludbe
14th December, 2013, 09:08 AM
Where i can get mcu & ftdi?

pierre renault
15th December, 2013, 09:55 PM
Help please. I galletto 3 v53 after installing all the program does not open, I get the information to upgrade. Someone can help me please!

ludbe
16th December, 2013, 04:54 PM
Where i can get mcu & ftdi?

anyone??????

carbon7319
18th December, 2013, 03:26 PM
Here you go , i download from this forum today and Galletto work perfect.Just use what ewer you want and user guides are inside rar.235553

gadroulll
24th December, 2013, 04:43 PM
i have found some difference you can try and explain some communication fault
eu has max485
china has max481
different MAX485 plus 1?A shutdown mode (MAX481)

eu has l9613
ch has l9637 what the difference?


can someone confirm them

serdarmsc
25th December, 2013, 10:31 AM
i 'am use L9637d, k-line working perfect.

ludbe
25th December, 2013, 11:07 AM
i 'am use L9637d, k-line working perfect.

what about can?

serdarmsc
26th December, 2013, 01:27 PM
82C250 or TJA1050. TJA1050 perfect for marelli ecus.

Multipla
27th December, 2013, 07:47 PM
Tanks marmes but when I connect to Galletto2 IAW 5sf8 model St10f296 not read into boot mode but the K-line works but the two 100 ohm resistors connect the right, unless it takes a 100 ohm 1/4 watt or 1/2 watt or more.

Autotecno2006
23rd January, 2014, 01:07 AM
Hi All, My V53 has red led on when i connect to pc, tryed another pc same thing, so must be unit, any ideas please, Regards P.

artek_was
25th January, 2014, 05:28 PM
Where i can get FIXED mcu & ftdi?

aleksandrzaharenko
29th January, 2014, 10:22 PM
Where i can get FIXED mcu & ftdi?


Help me, please

angelvoodoo
2nd February, 2014, 01:30 PM
hello guys i bought an fgtech V53,china clone. and i can not make it work.
i have this message "low voltage"
i tried almost everything i found but nothing worked.
any help , please?
package arrived yesterday and i really need it tommorow. chinese supplier is on chinese new year vacation!

morgano
2nd February, 2014, 04:46 PM
Low voltage appear if you are not connected to car via OBD.

xrhstaras77
2nd February, 2014, 05:19 PM
you love work; FULLY GENUINE

mecafrigo
5th February, 2014, 12:23 AM
RRR!! LOW VOLTAGE with v53 with obd or table ??? help pleaz

aleksandrzaharenko
28th February, 2014, 07:32 AM
Guys, I want to buy a CPU Galletto v53 + FTDI .


Where can I buy it?

cristim
14th March, 2014, 07:49 PM
can someone read the part from red circle?!!! from eu v54 clone.
is missing from a v53 china clone
v53 it has a cons here...250439

Foblas
14th March, 2014, 08:50 PM
Search for partnumber ADAA

Отправлено с моего Lenovo P780 через Tapatalk

aleksandrzaharenko
14th March, 2014, 08:58 PM
ADAA---MAX809

cristim
15th March, 2014, 07:19 AM
ADAA---MAX809

thanks man

barteczekk
15th March, 2014, 04:37 PM
Wow double post's . Sory

barteczekk
15th March, 2014, 04:43 PM
HELLO.I try fix k-line using this solution 250565250566 I need some help with fixing K-line at galletto2 v53. When i try identified ECU i get error msg. When i try read file he do something - going to 100% then software switch off. I measure pins 6-7 at U16 and is ~500 ohm. i change U16 for L9637D PIN nr3 lift up and connected to capacitor - voltage is 4.3. what else i can check or change.

barteczekk
15th March, 2014, 06:32 PM
Ok. Never mind, poor quality of soldering. Now K-line working.

cristim
15th March, 2014, 07:31 PM
today i took another fgtech v53 china, (i buyed 2 pieces), and....
surpriseeee, the pcb is identical, but canbus is working and those not have ADAA. condenser like my pcb
i hope not to be the MCU problem.

barteczekk
15th March, 2014, 07:47 PM
HMM. My K-line workin only when i heat pcb - hot air. when is worm all function k-line working well but when cold nothing work. what to do ?

J_amb_o
15th March, 2014, 10:02 PM
Buy the original?

barteczekk
15th March, 2014, 11:24 PM
You wish to be my sponsor ?

cristim
20th March, 2014, 07:46 PM
hi guys,
i need help with broken contact on pcb...
pin 5 from 82c250

cristim
21st March, 2014, 07:21 PM
no one where is going pin 5?

kosiik2
21st March, 2014, 10:18 PM
[QUOTE = cristim; 2257669] nikdo, kde bude čep 5 [/ QUOTE]?

How do you find a broken contact?

cristim
21st March, 2014, 10:47 PM
i broke pin from pcb :blue:
my hot air station is not working and when i cut the pins... broke pin 5 from pcb

lagas
22nd March, 2014, 12:41 PM
mate, this pin is not USED!

tehnosoftex
22nd March, 2014, 01:39 PM
Hi, I have 2 pieces of galletto v53, one bought from carsung, china, the other from ebay from a guy from italy. Both share the same software and I think both are made in china but the one that I bought from ebay it has a better quality of manufacture and the components are not erased, like in china one. The one from china did not work on can obd cars but it work on can in boot mode edc17. The italian one it seem to work properly on every test I made. I try both on:
edc17 boot mode read, write ok both
edc17 read obd italian ok, chinese failed
ford focus 1.8 tddi pwm itallian ok. chinese failed
mercedes delphi dcm3.5 piezotech jtag nexus both ok
vag tsi 1.2 simos itallian read ok. chinese failed
vag 19 tdi pd k line both ok
I noticed that even on the table without any connection to an ecu, if i try to ID a can ecu from vag the interfaces are reacting different. the italian one try to read a long time before it trows an error that the china one. I will try to make more tests and post the results

cristim
22nd March, 2014, 06:05 PM
in what tipe of case they are?!!!
china rounde corners?!!!

banza
22nd March, 2014, 07:45 PM
Hi, I have 2 pieces of galletto v53, one bought from carsung, china, the other from ebay from a guy from italy. Both share the same software and I think both are made in china but the one that I bought from ebay it has a better quality of manufacture and the components are not erased, like in china one. The one from china did not work on can obd cars but it work on can in boot mode edc17. The italian one it seem to work properly on every test I made. I try both on:
edc17 boot mode read, write ok both
edc17 read obd italian ok, chinese failed
ford focus 1.8 tddi pwm itallian ok. chinese failed
mercedes delphi dcm3.5 piezotech jtag nexus both ok
vag tsi 1.2 simos itallian read ok. chinese failed
vag 19 tdi pd k line both ok
I noticed that even on the table without any connection to an ecu, if i try to ID a can ecu from vag the interfaces are reacting different. the italian one try to read a long time before it trows an error that the china one. I will try to make more tests and post the results

can you give me the link of the ebay
seller?

tehnosoftex
22nd March, 2014, 10:33 PM
in what tipe of case they are?!!!
china rounde corners?!!!

Yes, china is with round corners.

tehnosoftex
22nd March, 2014, 10:41 PM
can you give me the link of the ebay
seller?

I buy from ebay.it, from the user universaltuning. The software is the same sh i t with the virus included but the hardware seem to be beter than the china one

cristim
23rd March, 2014, 06:07 AM
tehnosoftex (http://www.digital-kaos.co.uk/forums/members/87877-tehnosoftex/)
round corners, like my two galletto ( 1 good, 1 not)
the galletto from ebay it is china clone too, i saw a clone and the pcb it looks like eu clone, black relay... no scratched ic...
and a mark (number) on one side.
i think i wanna buy one...

pedroza
23rd March, 2014, 08:09 AM
Hello, I have a problem when I connect via OBD Ford shows me 18volt. How to solve?

pedroza
24th March, 2014, 07:16 PM
252011Hello what is the value indicated resistance

2200
24th March, 2014, 09:11 PM
4,7k..................

Hribeiro
31st March, 2014, 05:33 PM
Hi people. I have one galletto 3 V53 and don't work via obd. Say error wake1.
Help me please.

morgano
7th April, 2014, 08:46 AM
Hi again.

I have v53 that is not working on canbus, i already swapped with working one 82c250, relay, u17, u8, u9, and could not pass the priblem from defective unit to working one, so none of these were the problem.

Any idea what more ic or component should i swap to find the fault?




Regards,

bubu55
7th April, 2014, 09:23 AM
Hi again.

I have v53 that is not working on canbus, i already swapped with working one 82c250, relay, u17, u8, u9, and could not pass the priblem from defective unit to working one, so none of these were the problem.

Any idea what more ic or component should i swap to find the fault?




Regards,

If not work on can problem is bad mcu bin (mcu bad programmed)
You must change it or reprogram onboard

morgano
7th April, 2014, 10:35 AM
100% sure? Or maybe another component involved can be damaged?

overs0ull
7th April, 2014, 10:56 AM
Morgano post the picture what you replace - i have the same unit after few changes of resistors and can-bus filter and one other thing work like a charm now over BDM , Flash - edc16/EDC15 and EDC17 work great on CAN and K-line the voltage is normal 12 to 14 v not the problems with 18 or 9 v i will make the picture of my unit later and will upload it .
Make one of your

morgano
7th April, 2014, 11:05 AM
I already told in post.

I have a 100% working unit and a CANBUS failing unit.

I swapped parts from the failing unit to the working one with the intention to reproduce the fault in the working one and thus discover which part is the wrong one.

I swapped U9, U8, U17, 82C250, the relay that is next to the 82c250. Don't know if any other parts other than MCU are involved in CANBUS.

Can't post photo right now, but with the IC names you can see in your PCB the parts i swapped without success. After all swaps the failing V53 still fails and the working one (with replaced parts from the failing one) works, so none of these parts are responsible of the fault.

Regards,

2200
7th April, 2014, 08:24 PM
mcu is often fail in can, damaged mcu.... i have many repaired.

ddillenger84
11th April, 2014, 08:10 AM
I'm sorry if this has been beaten to death, but I can't find a solid answer. I have a V53, and know I must replace the resistor at U2 with an 809S/ADAA transistor. I assume based on the datasheet I need a SOT (not SC70) package, but there are a few options:

ON Semiconductor max809s Supervisory Circuits | Mouser (http://www.mouser.com/Semiconductors/Power-Management-ICs/Supervisory-Circuits/_/N-wnws?P=1z0z5la&Keyword=max809s&FS=True)

Can anyone be of some assistance? I'd be very appreciative.

morgano
11th April, 2014, 03:09 PM
Daz, mine works ok with the capacitor instead the max809.

Why do you want to change it? Does it fails somewhere?


Regards,

pedroza
13th April, 2014, 11:24 AM
Hello, I buy fgtech MCU V53 work communication CAN-H, CAN-L

boozyt
22nd April, 2014, 09:25 AM
Hello
I have a problem with galletto v53 k-line-no can-ok
does not work at all k-line
help someone solve the problem of?

lagas
22nd June, 2014, 06:06 PM
Any one try to write ford delphi dcm3.5 ecu tru jtag?

Read is ok, tomorrow whant to write maybe any one try already thanks.

tehnosoftex
24th June, 2014, 07:36 PM
Write ok with fgtech but not support the checksums. Checksums can be done with winols 2.24 but need some dump modification to be recognized by winols. The size read by galleto is bigger than the size required by winols.

lagas
24th June, 2014, 09:06 PM
Ok, thanks m8, same like i think. Need do cks before write.

lagas
25th June, 2014, 01:36 PM
Ok, write need tru obd this ecu and crc be corrected. But v53 give me silenKey error

Saniok888
2nd September, 2014, 12:44 AM
Write ok with fgtech but not support the checksums. Checksums can be done with winols 2.24 but need some dump modification to be recognized by winols. The size read by galleto is bigger than the size required by winols.


I tried to write back modified dump without CS on ford DCM3.5 via Galetto2 v53 J-Tag and it was working perfect!!! No need CS on this ECU, If somebody don't believe me, they can try ;)

Saniok888
2nd September, 2014, 12:47 AM
Ok, write need tru obd this ecu and crc be corrected. But v53 give me silenKey error

I had same problem, DCM3.5 write via OBD not working, and I write file back via Galeto v53 J-tag without CS, and car was working perfect!!!

lagas
2nd September, 2014, 04:39 PM
thanks for replay, i am not tried without cs. next time try have v54 try this on obd, and then jtag

crackerx
2nd September, 2014, 08:08 PM
please help me to repair my fgtech galetto on k-line protocol
working excellent on can i have read/write succesfuly many edc16 but not working on k-line

testet with edc15-not working
tested on three ME 7.5 - not working275561

morgano
3rd September, 2014, 12:04 AM
please help me to repair my fgtech galetto on k-line protocol
working excellent on can i have read/write succesfuly many edc16 but not working on k-line

testet with edc15-not working
tested on three ME 7.5 - not working275561

Below that little transistor you fit on pcb you should find a 10k resistor, change for 4k7 or 3k9 and kline should work.

crackerx
3rd September, 2014, 07:00 AM
ok i find it and i will change today and i will give you the answer

some people say that in my version of PCB the BDM port not working? is right?
and to work BDM and k-line i need to replace
3x original phillips circuits 74HC14 near the BDM port

1X HEF 4016BT near yellow relay

now near my yellow relay is HEF4016 but the tree circuits near the BDM port is not PHILLIPS

ludbe
3rd September, 2014, 10:34 AM
what about not working can line, what must be replaced?

morgano
3rd September, 2014, 12:44 PM
what about not working can line, what must be replaced?

MCU LPC2119

crackerx
3rd September, 2014, 02:31 PM
what about not working can line, what must be replaced?
LPC2119275663

your k-line is ok? voltage on eobd software is correct on you plug the interface to car?

crackerx
3rd September, 2014, 07:38 PM
plese help me to understand the problem
i have change the 10k resistor with 4k and still not working
275722

OVERSPEED
3rd September, 2014, 07:58 PM
I had an chinese F53 and even with another mods it never worked OK with ME7... even my euro clone (mini) can?t Write ME7.5.5 (with 29F800)

crackerx
3rd September, 2014, 08:05 PM
what tool i need to read write OK this me7 ecu.... mpps v13 clone is ok? i will connect battery charger an read and write ecu to have 13v

morgano
4th September, 2014, 12:01 AM
Try bootmode with fgtech. Your problem is that ecu is not supported by software V48, not interface problem. Now kline working well. Is just V48 sw doesn't have correct keys to open that ECU door.

crackerx
4th September, 2014, 06:16 AM
not working in boot mode i have try. i can change the sw version?any update ideea? many thanks morgano

morgano
4th September, 2014, 07:35 AM
For chsnge sw you need change hw :(


Regards,

OVERSPEED
4th September, 2014, 08:31 PM
what tool i need to read write OK this me7 ecu.... mpps v13 clone is ok? i will connect battery charger an read and write ecu to have 13v

the good ole boy 1260 is frawless with 512 and 1024Kb version in OBD, even one time I had problens writing and stop in the middle (Don?t know why), just start writing again without turn ignition off/on and it write all the way

motorsport
4th September, 2014, 10:05 PM
Hi someone know fix error low voltage on kline me7.5
But read id and flash good with sw v54 just showing low voltage error

crackerx
15th September, 2014, 02:25 PM
i have another problem with another fgtech 277355

the software show 23V not 12 and no relays "click" when connecting to OBD car ...

please help to understand the hardware problem

crackerx
17th September, 2014, 07:14 PM
i have repaired, one diode was broken but now working k-line and not working CAN
please help me to repair my fhtech 3led pcb , CAN
what i need to verify?

argegsm
20th October, 2014, 02:34 PM
hello who can tell me ..red marked transistor name's.. Q18 and Q20

carmageddon
21st October, 2014, 12:18 PM
hello who can tell me ..red marked transistor name's.. Q18 and Q20

Q18 = ZVP2106A
Q20 = ZNV2106A

Multipla
1st January, 2015, 05:06 PM
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=293042&stc=1293041http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=293040&stc=1293041See for all

dominik.m
12th February, 2015, 12:49 AM
Hi All.

what "sign" have marked elements.?

I ask about help.

SALUTE.

sumi1
12th February, 2015, 01:23 PM
for golf4 bosch me 7.5 read-write ok obd(13 v for write) galleto v54

kospoz
12th February, 2015, 02:03 PM
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=293042&stc=1293041http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=293040&stc=1293041See for all
what is the orange mark?

Multipla
16th February, 2015, 12:22 AM
Is the connection of MCU LPC2119.

Multipla
16th February, 2015, 12:35 AM
what is the orange mark?

J/Link connection

MKE
3rd May, 2017, 03:50 PM
So anyone have solution for ford visteon ecu reading?

AVDigitale
3rd May, 2017, 09:03 PM
hello i have china v54 galletto but is not working can ,bdm and jtag just kline this is my pcb

morgano
4th May, 2017, 07:45 AM
hello i have china v54 galletto but is not working can ,bdm and jtag just kline this is my pcb

Too many problems, you'd better buy new one i guess. Cheaper and faster solution.

AVDigitale
4th May, 2017, 07:11 PM
please tell me which componenets need to change or where to buy another to work with bdm ,jtag,can and kline do you have a link i am from europe

AVDigitale
4th May, 2017, 07:22 PM
i am purchased some elemenst but i am waiting

morgano
4th May, 2017, 09:25 PM
You change all components like most people do or spend time reversing and troubleshooting the circuit to find the failing parts. There is no other way to proceed.

garageozcar
18th September, 2018, 10:11 AM
anyone can help e for connect J-Link Seger to FGTECH v54 jtag please
Thanks

JorgeRio
18th February, 2019, 03:53 AM
hi,
the picture is for fgtech galletto 2 ?
the old 3 led,
here in spain have one unit for repair,
but several chips no references

need pass to winrar ??

JorgeRio
18th February, 2019, 04:37 AM
About J1850 in old G2...
pass for open the winrar ??