PDA

View Full Version : Fgtech Galletto 3 v53 PROBLEM !



Dennis-
8th October, 2013, 06:53 AM
Dear friends,
I got the new fgtech galletto 3 v53 chinese clone with usb dongle.
the install went fine and software running fine...

Yesterday i wanted to test it on a BMW 520d 2007 edc 16c35, could only get ecu info, NOT read dump or open file in the software ?
it did not work on k line or can, damm software refuses to read.....

Someone here that experience same thing ???

Thanks in advance

Regards
Dennis

Saulius Saulius
8th October, 2013, 06:36 PM
I have at the same problem with BMW 2007 3.0D X5 edc16c35, ID of ecu read ok, but can't read flash. Could you make foto of your fgtech pcb? I want compare it. Maybe someone know where is problem? My pcb here:

223496223497223498223499223501

Dennis-
8th October, 2013, 06:59 PM
Hello.
Strange this probleM, and it should be an A product !...but still a chinese clone.
Software and all runs fine, driver also.

Here is a picture of my pcb.


223506

Regards
Dennis

VRPerformance
8th October, 2013, 07:20 PM
Test on other cars,to see if working for others

Saulius Saulius
8th October, 2013, 07:48 PM
Hello.
Strange this probleM, and it should be an A product !...but still a chinese clone.
Software and all runs fine, driver also.

Here is a picture of my pcb.


223506

Regards
Dennis


Could you look what is under C28 capacitor, they in bottom middle. I can't see what is in left side. In my pcb you can see like jumper...

Dennis-
8th October, 2013, 08:27 PM
I looked now, and mine is exactly like your.

Saulius Saulius
8th October, 2013, 09:25 PM
I looked now, and mine is exactly like your.

Thank you.

Dennis-
8th October, 2013, 10:06 PM
Tomorrow morning iam gonna test in on Citroen c6 2.0hdi...see if it works.

I get back with the resault.

Dennis-
8th October, 2013, 10:48 PM
But the strange thing about it, is that i can do ecu info on all cars, but not read or open file for writing !!!!!!
When i pusch read button, the box dont "clic"...like it does with ecu info...and when press open file button, nothing happens.

Well it is a china clone so what to expect.

queroseno
8th October, 2013, 10:57 PM
EDC16U1 vag It does not work, K-line failure

Dennis-
8th October, 2013, 11:11 PM
EDC16U1 vag It does not work, K-line failure

Ok, so have you any solution for the k line or not possible to fix ?

Dennis-
9th October, 2013, 09:16 AM
Hello again...bad news !!
Just tried it on a Citroen c5 2.0 hdi siemens SID 803A ....can only do ECU DATA.....not read any car at all.

Saulius Saulius
9th October, 2013, 10:16 AM
I just now try read Vauxhall Vivaro 2.0 cdti EDC16CP33/C36 by K-line read ok!

Dennis-
9th October, 2013, 10:25 AM
Very good !
I think mine is broken, only had it for 2 days...not working at all.

My box click when i do ecu data, but no click when trying to read....just say it?s reading ecu, but nothing happends.

Saulius Saulius
9th October, 2013, 12:55 PM
How long you wait after push button "read"? I wait 30 sec after push button, then start read. Working little bit different like old fgtech v53.

Dennis-
9th October, 2013, 02:12 PM
I tried that now, and i waited 5min, still nothing happends grrrr
this driving me crazy....

Tomorrow the chinese supplier wanted to guide me on skype :)

What to guide????

I am not a noob doing this for many years.

Dennis-
9th October, 2013, 02:14 PM
If i buy a original galletto 2 slave, i heard that it could be patched to a master with latest sw...some one that can confirm that ?

DiegoAC
9th October, 2013, 03:41 PM
Mine never worked mate, got a refund from ecutool. Did you have to install through ghost image?
Cheers.


Hello.
Strange this probleM, and it should be an A product !...but still a chinese clone.
Software and all runs fine, driver also.

Here is a picture of my pcb.


223506

Regards
Dennis

Dennis-
9th October, 2013, 04:14 PM
Hi...
Yes, the only way to get it to work at all was to install the ghost image...then it started at last.
Is there a problem with the ghost image ?

I installed it on a ibm thinkpad t61...

Saulius Saulius
9th October, 2013, 05:45 PM
I install normal , without ghost, on toshiba satelite c660, set date 01 01 2013, then copy all from the cd to pc, then install, fix usb and start work!

DiegoAC
9th October, 2013, 10:46 PM
I guess there is something wrong with mine (the one that came with the damn thing). I tried on a Dell Vostro 3500 (Win7) and a Compaq N610C (XP) did the date switch before installing and followed all instructions. Never got the image to work...



Hi...
Yes, the only way to get it to work at all was to install the ghost image...then it started at last.
Is there a problem with the ghost image ?

I installed it on a ibm thinkpad t61...

Saulius Saulius
10th October, 2013, 07:38 AM
Date need change not before install, date need change before transfer files from cd to pc.

DiegoAC
10th October, 2013, 01:45 PM
Date need change not before install, date need change before transfer files from cd to pc.

Yup... tried that too

robkobg
10th October, 2013, 03:03 PM
May be it's waiting internet connection with Galletto server :top:.

AlexandruP
10th October, 2013, 03:05 PM
I found the problem on your PCB... is made in china and is crap.

DiegoAC
11th October, 2013, 01:55 PM
I found the problem on your PCB... is made in china and is crap.

Yeah... thanks for the news... fortunatelly got my money back.
Cheers.

Dennis-
11th October, 2013, 02:08 PM
Yes these chinese clones are totally SHIT !!!!!!

Where can i buy a eu clone for better price than 700 euro ?

or maybe not possible....

RicardoJvCruz
18th October, 2013, 02:12 PM
Hi, mine v53 from china have the same problem with all edc16 in OBD, read ECU ID ok but when i try to read nothing happens.

I've seen some china v53 working good with ec165 obd.

ishell
19th October, 2013, 05:33 PM
Have test my china v53 with vw T5 edc16 via obd.Read and write ok and fast (k-line)
Nothing replaced on pcb .

RicardoJvCruz
20th October, 2013, 02:20 AM
ishell (http://www.digital-kaos.co.uk/forums/members/85262-ishell/)
can you take some pictures of your interface ?

ishell
20th October, 2013, 08:01 AM
My tool in garage
But it look as well as others here .

jarecki55
20th October, 2013, 09:45 AM
my v53 work ok but no success on PCR2.1 read eprom,unlock?, read flash but when I try Write go to 100% end "Ecu rejected programming" I get tray on 2 ECU and no success :( ps. Skoda dealer take 40Euro for programming used ECU....

Dennis-
22nd October, 2013, 10:01 AM
Hi guys?s.
I little update.
I returned the box back to the supplier and got a new one, i now everything works !!
I had only test it on a citroen c5 2.0 hdi and a bmw 520d 2006 worked perfect...but this week i also try it on a nissan navara 2,5d 2007...
But i wonder if somone have the V53 software working without dongle for the chinese clones ?

Regards

Dennis-
22nd October, 2013, 10:22 AM
I found this tread, and it?s working like a charm ;)...bye bye dongle.

http://www.digital-kaos.co.uk/forums/f173/fgtech-v53-chinese-without-dongle-362735/