PDA

View Full Version : Experience with new tool GAlletto v54!



Pages : [1] 2

mcgustoo
18th November, 2013, 09:42 AM
Hi everybody how works your galletto v54 with difrents ecu???
i tested:
BDM
Delphi crd 2.61 with Jtag
edc16 can
its work ok

mcgustoo
19th November, 2013, 10:45 AM
DCM 1.2 clio with BGA st10F280 work perfect!

chiptorque
19th November, 2013, 11:33 AM
which provider is better? have the link? thanks

mcgustoo
19th November, 2013, 12:42 PM
Galletto 3 v54 MASTER (http://www.avtodiagnost.com/galletto-3-v54-master-en.html)
no dongle no shit !!!!

AlexandruP
19th November, 2013, 02:49 PM
GALLETTO 3 V54 (http://www.tunertool.com) portugal clone... also no dongle no shit... also v55 2013 update coming soon from them

elcarpuz
20th November, 2013, 01:10 PM
Test on truck, bosch 6.2 Works daf, scania...but test on volvo renault trw lucas ecu, not work :-(

no solution from tunertool.com

mcgustoo
20th November, 2013, 02:25 PM
When you write in this topic tested solution, please write where you bought Galletto ! Thanks

robkobg
20th November, 2013, 04:15 PM
That is the solution (http://www.fgtechnology.it/), everything other is shit.

mcgustoo
20th November, 2013, 06:12 PM
Yes pay 4000Eu and Make money!!!! after one year if something is wrong pay 1000eu for update...... this is non sense....
FGtech sell equip for 1000eu make update for 200eu and you will have a lot of buyer!!!! Then nobody wants china and others!

elcarpuz
20th November, 2013, 10:43 PM
OK, problem solved, interface works good, tunertool.com good quality tool and very good support!!!

mcgustoo
21st November, 2013, 08:35 PM
How you solved problem please answer!

vasco fernandes
22nd November, 2013, 07:13 PM
this tool have checksum for PCR 2.1 ?

AlexandruP
22nd November, 2013, 11:28 PM
Yes www.tunertool.com working very nicely for PCR2.1

I made some cars already and few days ago I made a 2012 Audi A1 1.6 TDI for dpf remove and tuning job, procedure is simple. need unlock first by tricore and then read/write by OBD.

robytza
26th November, 2013, 10:31 PM
bought galletto v54 mini from carprog and unfortunatelly it requires a dongle to run.
i dont have so many usb slots and its really bodering me.
can you please provide a solution to avoid dongle usage every time ?
also i am running it on win7 x64 and i have to set the date every time before starting the software to 4th january 2013.

AlexandruP
27th November, 2013, 01:50 AM
Should have bought tunertool.com portugal clone and not need dongle again!

robytza
27th November, 2013, 08:28 AM
the problem with the dongle was solved by a vendor idea. i`ll use a mini usb hub and its ok for me.
remains the changing date problem on win7.
runasdate is not working. doesn't know to change the date also for secondary started processes.

Gibon14
27th November, 2013, 11:35 AM
this tool have checksum for PCR 2.1 ?

With AES V54 mini, unlock and checksum work perfectly for PCR2.1.

morgano
27th November, 2013, 11:40 AM
@AlexandruP

Mate you look like a living advertising from t00n3rt00l.c0m. This, possibly, can start to be considered as SPAM. We understood it first time, you like it, but stop advertising in every post, is boring. ;)

mcgustoo
28th November, 2013, 02:30 PM
bought galletto v54 mini from carprog and unfortunatelly it requires a dongle to run.
i dont have so many usb slots and its really bodering me.
can you please provide a solution to avoid dongle usage every time ?
also i am running it on win7 x64 and i have to set the date every time before starting the software to 4th january 2013.


Yes carprog have dongle shit is the same like china !!!
About working carprog interfaces i dont know how works I never buy from him!!

But today tested edc17cp14 vag with boot mode and work perfectly! Read write is okay!
Now i have immo off solution for EDC17... more info on skype: jaroslaw.janota

kinetic
29th November, 2013, 05:35 PM
Just got a galletto v54 to update old v48, but wasnt able to install it yet as the cd didnt have the drivers. Contacted seller already, is going to send them by email today, i have a leon 1.6tdi to do tomorrow, and i?m curious to test it, two weeks ago i tried a v53 on an ibiza 1.6tdi but after unlocking perfectly the simos pcr2.1 i couldnt read or write by obd, had to use a cmd flshtec from a friend to write. Anyone as any drives i can try out?

b2s15
30th November, 2013, 09:40 PM
has someone could write sid803 ? i have one to make and i heard that it wasn' t working on this ecu.

tried on edc16c39 alfa159 , doesn't work by obd.
bdm ok , tried on 4 ecu Bosch.
edc17 passat 2.0tdi 2008, read and write ok by obd.
edc17 bmw320d 2008, ra ad write by obd ok
ec17c46, mb classe b 180cdi 2009, tricore read an write, ok also.

robytza
30th November, 2013, 11:15 PM
Opel Insignia 2.0CDTI 131HP - 2012
EDC17 Tricore SAK-1767 with TPROT 08
[NOT DONE] - ecu too new

offtopic : is any tool that can do this ecu ?

mcgustoo
2nd December, 2013, 08:28 AM
has someone could write sid803 ? i have one to make and i heard that it wasn' t working on this ecu.

tried on edc16c39 alfa159 , doesn't work by obd.
bdm ok , tried on 4 ecu Bosch.
edc17 passat 2.0tdi 2008, read and write ok by obd.
edc17 bmw320d 2008, ra ad write by obd ok
ec17c46, mb classe b 180cdi 2009, tricore read an write, ok also.

I test sid804 ford with obd work good!

For Tricore with Insignia must wait for next update!

rj22
2nd December, 2013, 09:16 AM
Citroen ECU DCM3.5 reading ok but when I try to write error SK1,


anyone know why?



does anyone have a description of what the errors SK1, SK2, SK3,.....

mcgustoo
2nd December, 2013, 09:41 AM
You read by obd? Try by JTAG

gomarota
2nd December, 2013, 11:23 AM
im using gallleto master fro0m tunertool and cannot write sid801a partner, just read..., ktag wrote it without problems

AlexandruP
2nd December, 2013, 11:32 AM
Opel Insignia 2.0CDTI 131HP - 2012
EDC17 Tricore SAK-1767 with TPROT 08
[NOT DONE] - ecu too new

offtopic : is any tool that can do this ecu ?

This is working only on 2013 version Galletto V55 firmware.

It is going to be released soon I hear :)

AlexandruP
2nd December, 2013, 11:32 AM
im using gallleto master fro0m tunertool and cannot write sid801a partner, just read..., ktag wrote it without problems

I have same problem too, it is a bug from original galletto my friend with original tool confirmed it also. I think its fixed in new software verisons now.

gomarota
2nd December, 2013, 11:48 AM
This is working only on 2013 version Galletto V55 firmware.

It is going to be released soon I hear :)

i heard same but im not so sure that it will be released

robytza
2nd December, 2013, 12:45 PM
i`ll wait for it :) i hope my v54 mini from CP is updatable

mcgustoo
2nd December, 2013, 12:50 PM
im using gallleto master fro0m tunertool and cannot write sid801a partner, just read..., ktag wrote it without problems

you are sure its no working? I write without problems with bootmode on car :) but before i have galletto v52 china and no problem for G54 i dont tried!

gomarota
2nd December, 2013, 08:10 PM
you are sure its no working? I write without problems with bootmode on car :) but before i have galletto v52 china and no problem for G54 i dont tried!

yes i am, i tried bootmode too, read ok but write says the well-know error: send file to fgtech.....

marciukx
2nd December, 2013, 08:35 PM
Maybe someone bought FG v54 from there Chip Tuning Tools :: OBD Tools :: AES Universal Flasher v2 (OBD + BDM + JTAG + Tricore Boot) - Auto Electronics Shop - Car Diagnostics, Immo, Keys, Mileage and Other Tools (http://www.auto-electronics.de/index.php?dispatch=products.view&product_id=29850)
It is with or without doungle?

b2s15
5th December, 2013, 09:58 AM
read bmd sid803, and write 449ko mod file by obd without problem , with v54.

AlexandruP
5th December, 2013, 05:54 PM
Maybe someone bought FG v54 from there Chip Tuning Tools :: OBD Tools :: AES Universal Flasher v2 (OBD + BDM + JTAG + Tricore Boot) - Auto Electronics Shop - Car Diagnostics, Immo, Keys, Mileage and Other Tools (http://www.auto-electronics.de/index.php?dispatch=products.view&product_id=29850)
It is with or without doungle?

Is without dongle but has many problems in the last generation... they never helped me solve my problem on v48 clone so I never buy AES clone again!!

mcgustoo
5th December, 2013, 08:45 PM
Is without dongle but has many problems in the last generation... they never helped me solve my problem on v48 clone so I never buy AES clone again!!

If you known problems please write on this topic customers need know about it! Regards!

lanya01
5th December, 2013, 08:58 PM
Hi!
I have Galletto2. You can upgrade to a newer version? If so, which is good to add? Can you help? Thanks for your response!

mcgustoo
9th December, 2013, 05:32 PM
No this galletto v2 have other hw

CFCM
9th December, 2013, 05:58 PM
Hi, Recently bought from tunertool and it came without dongle and without software.... V54 master; Right now not able to do anything!

AlexandruP
9th December, 2013, 06:14 PM
You need to just contact them for software as they send it via email or via skype usually.

mcgustoo
9th December, 2013, 10:03 PM
who have sw without the dongle and hw id generation?

bbturbo
10th December, 2013, 10:13 AM
I had the same issue plus the order took quite a while to arrive (3 wweeks plus). Contact them and they will send you the software and manual. Instructions to install are all there although for a first timer, it can be rather confusing, as is with me.


Hi, Recently bought from tunertool and it came without dongle and without software.... V54 master; Right now not able to do anything!

mugatu
15th December, 2013, 11:43 PM
I was told that they do not galletto good testing calculation checksun in EDC17 ecu

fes_786
16th December, 2013, 03:38 AM
does the v54 software read astra h denso ecu ?? obd? and also mazda 6 denso ecu obd??

arevolution
16th December, 2013, 09:12 AM
Hello, I was doing very bad experience of fgtechv54 you say it is all ok, great, well I say no, equipment improperly assembled, plastic cover damaged, referred to throughout the Components Clips welded any how I install, I put the driver etc ... nothing happens, but I am a computer, I try on XP, Vista, Seven, 4 pc in total, we take the hand on my pc, the seller tries, etc. .. in the end you tell me to return in Germany.

I ask if I can take one, I bought it, and my old one reception reimburse me, I request to send me the best by being on its operation, it says I can not because it is random wholesale.

Here is my experience, 2 purchases, same shit.

I specify my email, the seller will recognize here that I'm above their service to the end.

olliviercabon

mcgustoo
16th December, 2013, 11:13 AM
Denso ECU Opel ------ Try read with renesas cable. Regards

gomarota
16th December, 2013, 12:02 PM
fiat panda, galletto from tunertool cannot write iaw5af, just read and took 30 minutes

spider-wifi
16th December, 2013, 12:36 PM
hello,

I want to buy Galletto EU but I dont know whether it is better to wait to new version V55

fes_786
16th December, 2013, 12:47 PM
When's v55 coming out??

mcgustoo
16th December, 2013, 02:41 PM
maybe never :) someone must reverse mcu...... and crack sw. Before it must buy ori galletto :)

M4NIK
20th December, 2013, 09:25 PM
hi will this work on ford mondeo 130bhp tdci via obd socket thanks

AutoM
20th December, 2013, 11:29 PM
Hello, anybody try galletto on mercedes c 2011yr delphi crd3.10??

mcgustoo
23rd December, 2013, 10:04 AM
Hello, anybody try galletto on mercedes c 2011yr delphi crd3.10??

I think in V54 isnt driver for thats ecu!

mcgustoo
23rd December, 2013, 11:29 PM
Today i test renesas ecu 1.7cdti opel. Works good. Edc17 reno master tested work good.......

BrunoPT
24th December, 2013, 12:06 PM
Bravo 1.6 mjet edc16c39 galletto v54 clone eur don't read and write. The china clone work good lol

Enviado do meu GT-I9505 atrav?s de Tapatalk

robytza
24th December, 2013, 12:33 PM
From where is your euro clone ?

ludbe
24th December, 2013, 12:36 PM
which eu clone?

BrunoPT
24th December, 2013, 07:42 PM
Tunertool.com

AlexandruP
24th December, 2013, 10:49 PM
Tunertool.com

What error did you get?

Your china clone is v48?

jaxone
25th December, 2013, 12:59 AM
What error did you get?

Your china clone is v48?

Did you tested both ?


P.S. AlexandruP - tu esti "THE PROFESSOR" din echipa de la Hyperchips ?

mugatu
25th December, 2013, 01:00 AM
What error did you get?

Your china clone is v48?
You say that his proceeding galletto of tunertool.com has not worked bosch edc16c39 and that galletto Chinese clown if that I work correctly

mcgustoo
25th December, 2013, 01:50 PM
Now we know tunertool its not good 100% but i think ori galletto too.... all original tools have some bugs and they are fixed with update....

BrunoPT
25th December, 2013, 02:26 PM
What error did you get?

Your china clone is v48?

Contact fgtech lol
Yes china clone is v48

Merry cristmas mate

Enviado do meu GT-I9505 atrav?s de Tapatalk

moky
25th December, 2013, 04:30 PM
ktagg and kess clone are very good complement to fgtech ..no possible to work only with one hardware..all have their bugs.. ! :D

mugatu
30th December, 2013, 01:20 AM
This week proves FGTech v54 portugues clone ire publishing everything Realize

AlexandruP
30th December, 2013, 02:45 PM
what mean you?

turbocip
30th December, 2013, 10:29 PM
This week proves FGTech v54 portugues clone ire publishing everything Realize

Maybe you want to say v55 :)

Also , i write mazda 6 / rfn diesel 2.0 143hp - read - write ok

mauronow
3rd January, 2014, 03:37 PM
hello I need download the software to V54, I need to use it without crack. without dongle.
What are the steps to install?
I use win7 64 bit notebook.
thank you!

robytza
3rd January, 2014, 05:04 PM
Software is provided by the seller of the hardware.
You cannot install a newer software on an older hardware interface as i suppose you want to.

morgano
3rd January, 2014, 09:35 PM
We, non english speakers, sometimes make it difficult to understand what we want to say on forum. :)

But, yes, i understood same thing, he want sw update by other way, not his hw seller. :)


Regards,

sinan33
3rd January, 2014, 10:52 PM
Maybe you want to say v55 :)

Also , i write mazda 6 / rfn diesel 2.0 143hp - read - write ok
Woowww!!!
Will fgtech v55 be released next week?

robertos74
6th January, 2014, 09:00 PM
2.7 hdi siemens sid 201 ,mb edc16c31,vag simos 6.2 all bdm works well fg tech 54

vopi
7th January, 2014, 08:34 PM
Ford Delphi DCM3.5 done by tunertool device without problem by JTAG.
Galletto can write this ECU through OBD but I dont know If I can use file which I read by JTAG. Is there anybody who try write this ECU through the OBD with file which was readed by JTAG?

tunertool
7th January, 2014, 08:49 PM
2.7 hdi siemens sid 201 ,mb edc16c31,vag simos 6.2 all bdm works well fg tech 54

whose machine you did use?

robertos74
10th January, 2014, 01:53 AM
I use the Portuguese equipment

TCSTigersClaw
11th January, 2014, 09:49 AM
Fgtech 2 has a problem reading PSA/Fiat MM 48p2.80 ???

The file I get is 64 kb and the flas is Am29f400 so it should be 512kb, It reads half of it. Is there a way to read it all ?

gezame
11th January, 2014, 05:21 PM
Hi
Obd read is 64kb.
For all read 512kb, only desolder 29f400.

turbocip
11th January, 2014, 05:33 PM
With Galletto2 V54 from tunertool read/write Mercedes_Sprinter_2009_Delphi_CRD2_CAN_95KW_iCRD2
All work fine

mcgustoo
25th January, 2014, 12:52 PM
Hi this is software to galletto v54! Please test with some v53 and v54... Its full edited.......
http://rapidshare.com/share/576A7DF804588814BFECA35ED92D517C

I want to read LPC from galletto who want help please write to PM.


Thaks button is nice to see....:)

pass: V54

turbocip
25th January, 2014, 06:12 PM
whats mean Full Edited ?
Thanks

mcgustoo
25th January, 2014, 07:47 PM
fULL CRACKED:)

sinan33
25th January, 2014, 07:59 PM
fULL CRACKED:)
So we don't have to set the time to 1.1.2013 and we don't have to use fgtech repair while using v53?
Is it right?
Thank you!

ipejasinovic
25th January, 2014, 09:25 PM
This will work only with one specific EU clone ;)

Sent from my PAP4300 DUO using Tapatalk

sinan33
25th January, 2014, 09:46 PM
This will work only with one specific EU clone ;)

Sent from my PAP4300 DUO using Tapatalk
:( are you serious ?

ipejasinovic
25th January, 2014, 10:03 PM
Yep.

Sent from my PAP4300 DUO using Tapatalk

sinan33
25th January, 2014, 10:06 PM
Yep.

Sent from my PAP4300 DUO using Tapatalk
:( :( :( :( some updates are missed with that v54 software.
It only has 329 drivers; my v53 software has 343 drivers.

ipejasinovic
25th January, 2014, 10:17 PM
Maybe your software is from December and this one is from November

Sent from my PAP4300 DUO using Tapatalk

sinan33
25th January, 2014, 11:31 PM
I think so.

turbocip
26th January, 2014, 09:37 AM
How can i run the software, without hardware inside in usb ?
Its possible , sometime i want to check if one engine/car is in the list , and need to put usb cable- interface , and after start the software

mcgustoo
26th January, 2014, 12:02 PM
If you want run sw must have connected usb hardware.

sinan33
26th January, 2014, 12:08 PM
If you want run sw must have connected usb hardware.
Do you have 2013 updates of galletto?

turbocip
26th January, 2014, 02:39 PM
I want run without usb inside in computer

tunertool
26th January, 2014, 07:41 PM
Only works with tool connected, unless you find some hacked software.

turbocip
26th January, 2014, 09:29 PM
Oki, just asking , because sometime need to check some ecu-s
i know , i can open pdf file

popescovici11
28th January, 2014, 11:01 PM
FG Tech V54 from tunertool.com not work on Ford Mondeo 2.2tdci 175hp EDC16CP39.

Rito
28th January, 2014, 11:52 PM
I will receive V54 this week and will report after use...
I bought it in Portugal without dongle...


Thanks

automocion
6th February, 2014, 09:04 PM
Tomorrow I'll be in Portugal. There is a store or anyone know where I can find the guy who sell this?

AlexandruP
7th February, 2014, 09:05 AM
He will not meet up with anyone if thats what your thinking

Rito
7th February, 2014, 04:24 PM
Hin not have anyone more...

mcgustoo
13th February, 2014, 05:37 PM
Iaw5SF work perfect in bootmode!!!!

Rito
13th February, 2014, 05:42 PM
Audi EDC17CP14 "CAGA" Work perfect read and Write...

AlexandruP
14th February, 2014, 02:09 AM
From where did you two buy your tool? Is it euro clone?

Dobermann
15th February, 2014, 08:57 PM
hello folks,

short question did someon tryed with galletto V54 to make it work on win 7 64 bit system ?? CP galletto not work on win 7 64 only 32 bit ! why ? driver problem ??

rj22
15th February, 2014, 09:30 PM
who is able to decompile V55

blackpirate
15th February, 2014, 09:58 PM
who is able to decompile V55


if i remember well protection in a .dll..
still the main exe needs few patching after
ive doubds that v55...could be sorted out..
remember that the sw , ftdi must be paired with lpc......

robytza
15th February, 2014, 10:00 PM
hello folks,

short question did someon tryed with galletto V54 to make it work on win 7 64 bit system ?? CP galletto not work on win 7 64 only 32 bit ! why ? driver problem ??

hello.
i have v54 from CP and mine is working perfectly on win7 x64. you should use the dongle and copy the 2 dll files from the kit folder in windows system32 folder.
also change the date to 4 Jan 2013 in order to run. i made a sort script that is chaging the date and after run galletto and when exit change the date back.
don't try with runasdate because is not working on win7.

rj22
15th February, 2014, 10:12 PM
if i remember well protection in a .dll..
still the main exe needs few patching after
ive doubds that v55...could be sorted out..
remember that the sw , ftdi must be paired with lpc......


start-up is not a problem, the problem is authentication server

AlexandruP
16th February, 2014, 01:40 AM
hello folks,

short question did someon tryed with galletto V54 to make it work on win 7 64 bit system ?? CP galletto not work on win 7 64 only 32 bit ! why ? driver problem ??

im using windows 7 64bit perfectly from tunertool.com, no dongle and no china crap.

Dobermann
22nd February, 2014, 10:59 PM
This will work only with one specific EU clone ;)

Sent from my PAP4300 DUO using Tapatalk

Hello witch specific eu clone you mean ?? please explain !! my clone use exactly this postet v54 software !

mcgustoo
23rd February, 2014, 10:42 AM
I tested PCR2.1 from Fabia. All works good read, unlock, write..... all ok!!!

robytza
23rd February, 2014, 10:57 AM
V54 from ?

bbturbo
24th February, 2014, 11:10 AM
I am trying to read the Bosch ME7.8 using the V54. Followed the instructions via boot mode (using 100ohm resistor to ground etc). It should be straight forward but I can't read it as it states BOOT MODE INACTIVE. I've triple checked that I got the boot pin/mode connected via 100ohm resistor to one of the ground leads from the V54 unit and the ve+, ve- and K-line are all connected. Instructions picture indicated;
Micro ST10F275
Driver ST10F273/5/6 Boot mode

I've selected driver/tool boot/ST10Fxx/ST10F273/5/6 Boot mode

Hope someone can help.

I've also given up contacting the seller (tunertool) as he does not reply via his skype account. Support has been very poor. I bought this last year and have been requesting for a somewhat better instructions/pics as the accompanying documentation is hard to understand for a newbie. No reply and I've not been able to use this since I bought it.

bbturbo
24th February, 2014, 03:00 PM
Following my earlier thread, perhaps some kind souls can provide me a clearer or more comprehensive manual in how to use the unit. e.g. how to use the OBD2 (zero info on this), which harness to use when doing k-line etc, what each coloured wire is (i know red = +ve etc but there are for instance 2 greens in a single harness. At the moment, I am just making guesses and doing trial and error and so far, I have not succeeded in reading a single ecu. I just used my kess v2 clone to the read the above me7.8 via OBD2 and it took me no more than 3 mins and the kess v2 is only a fraction of the cost of this V54 euro clone. I was unsuccessful with the V54, both OBD2 and bench - both indicating BOOT MODE INACTIVE. Perhaps I don't know how to use the unit due to lack of instructions.

Hope someone can guide me. Thanks in advance.

Dobermann
24th February, 2014, 04:50 PM
I am trying to read the Bosch ME7.8 using the V54. Followed the instructions via boot mode (using 100ohm resistor to ground etc). It should be straight forward but I can't read it as it states BOOT MODE INACTIVE. I've triple checked that I got the boot pin/mode connected via 100ohm resistor to one of the ground leads from the V54 unit and the ve+, ve- and K-line are all connected. Instructions picture indicated;
Micro ST10F275
Driver ST10F273/5/6 Boot mode

I've selected driver/tool boot/ST10Fxx/ST10F273/5/6 Boot mode

Hope someone can help.

I've also given up contacting the seller (tunertool) as he does not reply via his skype account. Support has been very poor. I bought this last year and have been requesting for a somewhat better instructions/pics as the accompanying documentation is hard to understand for a newbie. No reply and I've not been able to use this since I bought it.

hello bbturbo,

i think you chose the wrong driver ! as i remember bosch me7.8 like (porsche) use infineon c167 prozessor !! not st10

here is a pic for the pinout !! please have a look !

br regards !

AlexandruP
24th February, 2014, 07:53 PM
Yes you are using the wrong driver, me7.8 uses infineon c167 mcu not st10, if you select the correct menu you will have luck. And I spoke to tunertool today and he replied to me right away... maybe you caught him at a bad time?

bbturbo
25th February, 2014, 01:04 AM
Hello Dobermann,

Thanks for the quick reply!

It does not look like the pic of yours but exactly like the one shown in 'document' for ME7.8_ The top board has a ST10 chip and an Infineon chip. The Boot pin is underneath the board i.e. not on the same side as the chips. Reading it with Kess V2, I got the following details;

Hw: 0261206579 Sw: 1037350598

I would like to ask when you read, do you need to remove the boot pin once power is applied?

Hello AlexandruP,

Thanks for the prompt reply as well. I've left a few messages via Skype but no replies from him. To be fair, initially he did provide some guidance during the installation but thereafter radio silence. Granted there were a few questions asked but that is expected from someone who is entirely new to the V54.

Is it possible for you to perhaps send me a manual with more friendly instructions/guide? it has been over 5/6 months and I still have no idea if this unit works. So far I have tried on 3 ecus; Siemens SIM4LKE, Bosch ME7.8, Bosch MED17 and they failed to read with the V54 :-(. I eventually used the KessV2 clone for the first two and EVC BSL for the last one to read/write.

bbturbo
25th February, 2014, 01:58 AM
I've taken photos of the ecu. The bottom is where the boot pin is according to the document that came together with the V54.

tunertool
25th February, 2014, 02:33 AM
Pm me I will give you my skype and you can contact me. I think you have my old skype

yas200
25th February, 2014, 09:18 AM
I try read sid807 PSA 1796 - NOT WORK!!! Galetto2 EU clone v54

AlexandruP
25th February, 2014, 03:18 PM
I try read sid807 PSA 1796 - NOT WORK!!! Galetto2 EU clone v54

From which seller?

ipejasinovic
25th February, 2014, 09:17 PM
Hello witch specific eu clone you mean ?? please explain !! my clone use exactly this postet v54 software !
AES device, originally. But some guys later copied AES device. So, maybe AES, maybe copy of AES.

bbturbo
26th February, 2014, 08:42 AM
Tunertool, I have PM you and no reply.

yas200
26th February, 2014, 12:13 PM
From which seller?
Autodiagnost
Belarus

Kanemoto46
26th February, 2014, 01:42 PM
Hi guys,

i read all topic but i'd know... i have a galletto clone v53 from china, with black box and two leds. Work properly in bdm, jtag, simos pcr, k-line, can, etc, but work only in win xp, without dongle, and with the date to 1 januay 2013. I'd know if can update my device to V54, or i can do work it with WIN7 32bit.

rEGARDS

bbturbo
26th February, 2014, 03:45 PM
As usual no reply from tunertool.

Would someone be able to help with the manual on how to use the V54? appreciate very much the help as I do not have the car with me for so many days. I also want to find out if the V54 sent to me is in working order.

Thanks in advance.

moky
26th February, 2014, 08:44 PM
V54 from cp work fine so i have my v48 euro to sell,if interested..pm

milkatrek
26th February, 2014, 09:42 PM
Sprinter edc16 edc17 - read/write OK obd2
bmw edc16 2.0d read/write OK obd2
peugeot 1.6hdi edc16 Read/write OK obd2
John deere L4 - read/write OK obd2
Audi edc17cp14 20tdi caga read/write OK bootmode

koyot
26th February, 2014, 11:03 PM
I'm surprised

bbturbo
27th February, 2014, 03:37 AM
anyone can help?

with the boot pin connected to ground, and power turned on, do you remove the pin or leave it connected to ground when you want to read/write? what is the procedure?

I have also assumed that the k-line wire is the green of the Renesas cable (again assuming this harness cable is used for boot mode as the other longer harness is for tricore). I am not sure what the white and purple wires are for. The Renesas cable has;

4 x reds - +12v
4 x blacks - gnd
1 x white - ?
1 x green - k-line perhaps?
1 x purple - ?

My assumption that k-line is green is based on the document pic of the boot pin where the k-line pin indication on the connector is green. However upon looking at other jpg pics, k-line indication are in white and yellow too! so it's confusing for a first time user.

The documentation for tricore is more comprehensive as it shows what the different coloured wires are

BTW I have tried selecting both drivers; C167 and ST10F275.. both boot mode inactive

kugglefischer
27th February, 2014, 11:46 AM
V54 from cp work fine so i have my v48 euro to sell,if interested..pm
hi
who is cp?

and what is your price for v48?
whats included?
and which ecu's do it read and write?
boot mode ok?

please pm me...
thanks

eduzgz
27th February, 2014, 02:24 PM
hi
who is cp?

and what is your price for v48?
whats included?
and which ecu's do it read and write?
boot mode ok?

please pm me...
thanks

cp is cp2010 have a web car-prog.com if you're interested in have a look of his clones.
Cheers


Sent from my iPhone using Tapatalk

robytza
27th February, 2014, 03:24 PM
i`m also using CP interfaces. very good v54 clone. no problems until now. the only bad thing is that is mandatory to use it with dongle and FTDI drivers of the interface are not compatible with other interfaces that you may own (like VCDS, BMW Ecu Explorer, INPA D-CAN, VCP, etc) and every time should switch the drivers as you need. Also date should be moved back in order to run the program.

bbturbo
28th February, 2014, 10:59 AM
tunertool has contacted me and is providing assistance. there appears to be some misunderstanding. all is good now.

AlexandruP
28th February, 2014, 11:19 AM
Date must be moved back like china clone? Wow it must use the same protection as china clone :P

Catalin_TCM
1st March, 2014, 09:17 PM
From car-prog in win xp is not necesary to change the date ! Only in win 7 . Is a very good clone !

AlexandruP
2nd March, 2014, 01:26 AM
Original tool doesn't require any change date, so clone should be same as original otherwise it is not TRUE CLONE

mugatu
3rd March, 2014, 11:41 PM
The date change is because the software was cloned into 1-1-13 date and does not support work on actual dates, clone car-prog is perfect and more quality than Portuguese, I've had both.

morgano
4th March, 2014, 01:44 PM
The date change is because the license stored in the FTDI expires after 01-01-2013, the "donor" fgtech where data was taken from would expire that date, that's the only reason, cloning without the knowledge to extend the license.

Putting appropiate data in FTDI should cure the date change problem.

Even some EU clone (i have seen its sw) suffer this problem, but they hide it using a loader that makes the date change on the fly. They packed loader with Temida, but not hard enough to prevent have a look into it :)

Not everybody cracked the license schema stored in FTDI. They just copy the data and suffer date problems.

Dobermann
4th March, 2014, 11:44 PM
The date change is because the license stored in the FTDI expires after 01-01-2013, the "donor" fgtech where data was taken from would expire that date, that's the only reason, cloning without the knowledge to extend the license.

Putting appropiate data in FTDI should cure the date change problem.

Even some EU clone (i have seen its sw) suffer this problem, but they hide it using a loader that makes the date change on the fly. They packed loader with Temida, but not hard enough to prevent have a look into it :)

Not everybody cracked the license schema stored in FTDI. They just copy the data and suffer date problems.

i think that could be right ! my v54 clone is from austria an change date to 30.12.12 and after start v54 software it change back to aktuall date

my clone work good the only thing is the Volt shows not right value ! it shows only 10,8 volt but real volt are 13,8

scartplug
5th March, 2014, 09:39 AM
I use the Austrian v54 clone it read Delphi 3.5 but did not write via Bdm and did not write with obd but older v53 write via obd no problem

elchip
5th March, 2014, 10:42 AM
i think that could be right ! my v54 clone is from austria an change date to 30.12.12 and after start v54 software it change back to aktuall date

my clone work good the only thing is the Volt shows not right value ! it shows only 10,8 volt but real volt are 13,8

You have updated HW48 to V54 and problem on voltage is in your tool not in V54 upgrade. Austrian clone is 1001% OK "
So next time write all data about your tool not only like these time .

theghost
5th March, 2014, 02:45 PM
@scartplug:
maybe you use china/EU clone on same laptop/pc -> then such things can appear

@doberman:
at an upgraded FW48 to FW54 there are following limitations due to the older HW (and also different usage of MCU pins)

-> JTAG can't work
-> Voltage can be displayed wrong (so or so this value is always only a unaccurate value)

scartplug
6th March, 2014, 01:08 AM
[QUOTE=theghost;2244701]@scartplug:
maybe you use china/EU clone on same laptop/pc -> then such things can appear

Yes I had old Chinese software on this pc. How do I fix this problem ?

theghost
6th March, 2014, 09:11 AM
best is to use a virgin XP -> than it will work best -> no conflicts

nebojsapejcic
6th March, 2014, 09:42 AM
where can I buy austrian clone?

theghost
6th March, 2014, 09:45 AM
contact me via PM and i will give you contact

nebojsapejcic
6th March, 2014, 10:20 AM
contact me via PM and i will give you contact
hello
your inbox is full , please empty it so I can send you pm

elchip
6th March, 2014, 10:22 AM
best is to use a virgin XP -> than it will work best -> no conflicts

Do you know instal XP ? And what conflict you have ?

soundnavigator
7th March, 2014, 08:58 PM
Can I read SID902 from Ford F-250 with FGTech 3 v54 ?

scartplug
7th March, 2014, 09:41 PM
I did as you said I formatted my laptop today and did a fresh install ! Hope the next Delphi 3.5 will work ;)

thanks guys

jr2185
8th March, 2014, 03:10 AM
Has anyone tested the v54 aes flasher on IVECO ms6.2?

Sent from my XT875 using Tapatalk

mexanico1971
8th March, 2014, 01:19 PM
[QUOTE=theghost;2244701]@scartplug:
maybe you use china/EU clone on same laptop/pc -> then such things can appear

Yes I had old Chinese software on this pc. How do I fix this problem ?

make other partition on the HDD !

BR

theghost
8th March, 2014, 03:55 PM
Wont work-> windows must be in c:\windows br

mcgustoo
12th March, 2014, 09:05 PM
I agree sid807evo not working!

aleksandrzaharenko
12th March, 2014, 10:02 PM
Guys help, wanted eeprom dump Galletto V53 Portugal clone

Dobermann
28th March, 2014, 02:46 AM
Hello Tuners,

i need help with simos PCR2.1 , i use Galletto V54 from Austria.

I did all connections like in the Fgtech Manual. i did the unlock and software tells me unlock ok.

i cant read the eeprom ! i have seen in this video a option for read eeprom >> https://www.youtube.com/watch?v=hpFvish_X5g

i put the ecu back in car and i have this error shown in the pic.

car starts bad and have RPM round about 1100 but runs normal !

someone did have similar trouble with simos pcr2.1 ??

here is the readed file over OBD !

did someon know why the unlock should be done only one time ??

thanks for help !!

Br Dobermann

gezame
28th March, 2014, 03:06 AM
Hi
I make various simos pcr, with fgtech V53 chiness, without problema, read-write eeprom, unlock, etc.
You are secure do not damage the ecu to open?
Br.

Dobermann
28th March, 2014, 03:14 AM
Hi
I make various simos pcr, with fgtech V53 chiness, without problema, read-write eeprom, unlock, etc.
You are secure do not damage the ecu to open?
Br.


yes im sure i did nothing damage by opening the ecu ! i was really careful !

i have V54 eu i cant read the eeprom only unlock !

gezame
28th March, 2014, 03:17 AM
Hi
I make various simos pcr2.1, with fgtech V53 chiness, without problems, read-write eeprom, unlock, etc.
You are secure do not damage the ecu to open?
Br.

gezame
28th March, 2014, 03:19 AM
Hi
Same problema wih fgtech V53 EU, software is older than fgtech V53 cinesse.

Dobermann
28th March, 2014, 03:24 AM
Hi
Same problema wih fgtech V53 EU, software is older than fgtech V53 cinesse.

ok thanks i didnt know that ! !! maybe something goas wrong by unlock the ecu ??

gezame
28th March, 2014, 03:50 AM
ok thanks i didnt know that ! !! maybe something goas wrong by unlock the ecu ??

Hi
Yes, maybe some damage to the dump of eeprom to unlock

Dobermann
28th March, 2014, 04:01 AM
Hi
Yes, maybe some damage to the dump of eeprom to unlock

yes i think so too !! but how to repair if i can not read the eeprom !!

maybe i buy chinese v53 ! this is really a joke i have eu v54 and cant read eeprom ! and CHINESE v53 can !! LOL

:confusion::confusion::confusion::confusion:

robytza
28th March, 2014, 08:10 AM
that error doesn't mean that you broke the ecu.
is the crankshaft speed senzor broken. maybe its a pure coincidence.
you can change it to see if the problem persists. because of that your got wrong rpm.

morgano
28th March, 2014, 11:21 AM
I agree robytza (http://www.digital-kaos.co.uk/forums/members/125109-robytza/)

Unlock is a simple process in eeprom dump, just invert 8 words, it should not damage car behaviour. And unlock is needed once only because if you invert the words two times the ecu become locked again.

Dobermann
28th March, 2014, 04:26 PM
ok i understand ! but the funny thing is ! this error hapen only after unlock ! and why should the crankshaft speed sensor broken ! before unlock there was no fault in engine ecu !

i will replace the sensor and have a look ! rpm is at 1100 at the moment and starts really bad ! but i can drive !

if i make the unlock 3 times the ecu is unlocked ! is that right ? first time invert the bytes to unlock > 2. time back and 3. time make unlock again !

br

robytza
28th March, 2014, 06:23 PM
maybe coincidence.....
things broke in general when its happen to be. maybe for that sensor the time has ended.
can be also a synchronization problem....

or maybe you broke some ecu wiring that is communicating with that sensor...
the easy way is to replace the sensor and see...

fuseppe
30th March, 2014, 10:51 AM
hi everybody, i see on cina store fgtech v54 what do you think about it? i read that work on windows 7 and 8

theghost
30th March, 2014, 11:30 AM
With fw54 i is not possible to read eeprom only to unlock it.

This is the procedure like fgtech made it.

If it was possible with any other earlier version than fgtech changed the procedure in fw54.

robytza
30th March, 2014, 11:51 AM
Car-prog v54 is also working on win7 x64. I am using it for a while

turbocip
30th March, 2014, 12:02 PM
Sure !
It work on 64bits.

sinan33
30th March, 2014, 02:35 PM
I agree sid807evo not working!
Sid807Evo can be read with galletto v53 and v54 easily but you know Sid807Evo have password protection so galletto just can't read the pw protected sid807Evos; all the the other is OK and works perfect.

sinan33
30th March, 2014, 02:44 PM
I try read sid807 PSA 1796 - NOT WORK!!! Galetto2 EU clone v54
Galletto v53 and v54 can read and write sid807/Sid807Evo easily.
With PSA ecus you should use the Sid807 connection scheme provided by fgtech for both Sid807 an Sid807Evo.
With Ford's Sid807Evo you should use the scheme of Optican but Ford's ecus are password protected and you can't get the pw using galletto.

mcgustoo
2nd April, 2014, 06:36 AM
Hello Tuners,

i need help with simos PCR2.1 , i use Galletto V54 from Austria.

I did all connections like in the Fgtech Manual. i did the unlock and software tells me unlock ok.

i cant read the eeprom ! i have seen in this video a option for read eeprom >> https://www.youtube.com/watch?v=hpFvish_X5g

i put the ecu back in car and i have this error shown in the pic.

car starts bad and have RPM round about 1100 but runs normal !

someone did have similar trouble with simos pcr2.1 ??

here is the readed file over OBD !

did someon know why the unlock should be done only one time ??

thanks for help !!

Br Dobermann

I think galletto only do unlock on table for this ecu not read eeprom! Tricore flash read in car on obd becouse must have immo for read !!!
REGARDS

sinan33
2nd April, 2014, 01:22 PM
You are right McGustoo.

cp2010
2nd April, 2014, 09:56 PM
no ...
in boot mode can unlock and read/wriete eeprom (but software from 12/2012)
read/write via obd working on table also, no need immo

gery11
3rd April, 2014, 02:04 PM
Is tunertool a realiable seller? I tried to contact him, but he never asnwer. On skype I speak to him and never get an answer?
Does somebody has carprog tool?
Tested with simos pcr2.1?

robytza
3rd April, 2014, 04:19 PM
Try carprog. Its ok

sinan33
3rd April, 2014, 05:07 PM
Car-prog tool can read/write pcr 2.1

gery11
3rd April, 2014, 05:13 PM
it says it can write it, but have you tried to unlock, read and write via obd and simos pcr?
The only problem i see of carprog is the dongle..
But the price is better

scartplug
3rd April, 2014, 10:19 PM
Anyone try the v54 euro Austria clone on a Mazda 6 2008 2.0 diesel denso rf8x or 7x I tried via obd with the Delphi and Bosch(I think) today but not work so must be denso. Costumer wants to do this Dpf job in a few weeks and I need to be positive my tool works on it.

foden
3rd April, 2014, 10:30 PM
wouldn't mind knowing which European one to go for myself have spoken on Skype to tunertool
its been discussed a lot but are there really any differences between the euro ones available?

infinityecu
4th April, 2014, 01:42 AM
[QUOTE = mcgustoo; 2211021] Ciao questo ? un software per Galletto V54! Si prega di verificare con una certa V53 e V54 ... La sua piena cura ....... http://rapidshare.com/share/576A7DF804588814BFECA35ED92D517C voglio leggere LPC da galletto che vogliono aiuto potete scrivere a PM. pulsante Thaks ? bello da vedere .... passare: V54 [/ QUOTE]






:)

​​Hello password V 54 rar file tells me it's wrong .. thanking you in advance Could you give the correct password?

youk
4th April, 2014, 09:49 AM
password v54

infinityecu
4th April, 2014, 09:59 AM
[QUOTE = Youk; 2268340] la password V54 la [/ QUOTE]

Hello thanks for the ripsosta but as soon as I put password V54 gives me error therefore conclude that there is a problem with l rar files as it has been compressed or the password is not the one

infinityecu
4th April, 2014, 10:02 AM
[QUOTE = Youk; 2268340] la password V54 [/ QUOTE]


I stand corrected and thank you very much the problem that I see with digitavo V54 capital therefore gave me error, Thanks for reply.

gery11
4th April, 2014, 12:18 PM
Anyone tested simos pcr with carprog clone?

bubu55
4th April, 2014, 02:59 PM
At this moment there are 3 differente situations:

-Fgtech v53 cinese tools (working only on win xp) upgradable to win 7 with license key (package protected with winlicense, easy to crack)
-Fgtech v54 eu tools work in win xp and win 7
-Fgtech v54 chinese tools working on win 7 (some nxp id, common with eu version, no need activation)

But there is a problem that no one says.....
All win7 version sw are very very unstable, some bugs in exe are present.

I tested all tools and all condition of working and the best solution is to use fgtech v54 EU made in xp machine; full working, no bug, and no problem on use.
The same tool used on windows 7 due to compatibility problems with some communication protocols (bad exe compile probably)

youk
4th April, 2014, 03:06 PM
password: v54

not V54

robytza
4th April, 2014, 04:29 PM
bubu you're partialy wrong.
if you know how to install them. ... v53 and v52 chinese are working also on win7 x32 an x64
i did them and worked perfectly without any licence

regarding v54 ... i had one bug on xp and no bugs on win7 x64.

sinan33
5th April, 2014, 12:10 PM
bubu you're partialy wrong.
if you know how to install them. ... v53 and v52 chinese are working also on win7 x32 an x64
i did them and worked perfectly without any licence

regarding v54 ... i had one bug on xp and no bugs on win7 x64.
Did you change the date when using your installation method?

bubu55
5th April, 2014, 12:50 PM
Did you change the date when using your installation method?

Robytza has confused the versions.


With normal install (provided by chinese) fgtech v53 not work in windows 7 (bad compile) because gave error:


ESEGUIRE RENEWAL CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- MAKE RENEWAL WITH FGTech_DOWNLOAD_UPDATE FOR TOOL RE-ESTABLISHMENT

There is One version that work in any clone (chinese clones too) and in windows 7.
Name of package is: "FGtech Galletto Edited v1.0.exe"
This version for running correctly need to use a "regkey.dat", generated in accord with exe "Get_hw.exe".

Directory di C:\FGTech

13/07/2013 05:36 1.098 apertura.dat
13/07/2013 05:36 44.832 auto.txt
13/07/2013 05:36 94.208 CALC.EXE
05/04/2014 13:41 <DIR> chk
05/04/2014 13:41 <DIR> DOCUMENTS
05/04/2014 13:41 <DIR> DOCUMENTS_NEW_TOOL
05/04/2014 13:45 0 elencocartellawindows.txt
13/07/2013 05:36 1.452.544 EOBD.exe
13/07/2013 05:36 58 eobd2.cfg
13/07/2013 05:36 4.329.472 EOBD2.exe
13/07/2013 05:36 4.026.368 FGTech_DOWNLOAD_UPDATE.exe
13/07/2013 05:36 2.482.751 FGTech_EOBD2_User_Manual.pdf
05/04/2014 13:41 <DIR> fgtech_new_driver
13/07/2013 05:36 1.439.744 FWUpdate.exe
13/07/2013 05:36 2.033 galletto.iss
13/07/2013 05:36 1.245.184 Gcheck.bak.dll
13/07/2013 05:36 1.245.184 Gcheck.dll
29/03/2013 16:31 1.039.872 get_hw.exe
13/07/2013 05:36 983.040 GHelper.exe
05/04/2014 13:41 <DIR> help
05/04/2014 13:41 <DIR> immagini
13/07/2013 05:36 2.200 Informazioni.txt
05/04/2014 13:41 <DIR> languages
05/04/2014 13:41 <DIR> languages_eobd2
13/07/2013 05:36 122.880 multiROM.bak.dll
13/07/2013 05:36 122.880 multiROM.dll
13/07/2013 05:36 74.240 README_SETUP.doc
13/07/2013 05:36 10.499 README_SETUP.TXT
06/07/2013 22:51 412 regkey.dat
13/07/2013 05:36 2.347 TABELLA CORRISPONDENZA EPROM.EEPROM.txt
13/07/2013 05:36 60.928 TAB_COMPARAZIONE_EPROM_Service_Bosch.doc
05/04/2014 13:41 55.094 unins000.dat
13/07/2013 05:36 717.985 unins000.exe
05/04/2014 13:41 <DIR> user
22/04/2013 23:05 165.376 Win 7.exe
13/07/2013 05:36 1.437.696 winmap.exe
27 File 21.158.925 byte
11 Directory 742.664.269.824 byte disponibili

If you remove regkey.dat, sw not start, if you run sw with non congruent regkey.dat sw start but not recognize instrument.

This exe is protected with winlicense, very esay to remove, now i'm working on it for offer free working solution for all dk users:top:

sinan33
5th April, 2014, 09:21 PM
As i saw the galletto edited version is working with galletto v54; it needs a different ftdi to work with galletto v53.
Am i wrong?

bubu55
6th April, 2014, 12:43 PM
As i saw the galletto edited version is working with galletto v54; it needs a different ftdi to work with galletto v53.
Am i wrong?

Probably wrong.
Problem is not ftdi but serial number inside nxp processor

infinityecu
6th April, 2014, 01:32 PM
. [QUOTE = bubu55; 2269284] Robytza ha confuso le versioni Con normale installazione (fornito dal cinese) FGTech v53 non funziona in Windows 7 (mala compilazione), perch? ha dato errore: eseguire RINNOVO CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- FARE CON RINNOVO FGTech_DOWNLOAD_UPDATE PER TOOL RIPRISTINO ce n'? una versione che funziona in ogni clone (troppo cloni cinesi) e in Windows 7. Nome del pacchetto ?: "FGTech Galletto Edited v1.0.exe" Questa versione per il corretto funzionamento ? necessario utilizzare un " . regkey.dat ", generato in accordo con exe" Get_hw.exe " Directory di C: \ FGTech 13/07/2013 05:36 1.098 apertura.dat 13/07/2013 05:36 44,832 auto.txt 13/07 / 2013 05:36 94,208 CALC.EXE 2014/05/04 13:41 <DIR> chk 2014/05/04 13:41 DOCUMENTI <dir> 2014/05/04 13:41 <DIR> DOCUMENTS_NEW_TOOL 2014/05/04 13 : 45 0 elencocartellawindows.txt 13/07/2013 05:36 1.452.544 EOBD.exe 13/07/2013 05:36 58 eobd2.cfg 13/07/2013 05:36 4.329.472 EOBD2.exe 13/07 / 2013 05:36 4.026.368 FGTech_DOWNLOAD_UPDATE.exe 13/07/2013 05:36 2.482.751 FGTech_EOBD2_User_Manual.pdf 2014/05/04 13:41 <DIR> fgtech_new_driver 13/07/2013 05:36 1.439.744 FWUpdate.exe 13/07/2013 05:36 2.033 galletto.iss 13/07/2013 05:36 1.245.184 Gcheck.bak.dll 13/07/2013 05:36 1.245.184 Gcheck.dll 29/03/2013 16:31 1.039.872 get_hw.exe 13/07/2013 05:36 983,040 GHelper.exe 2014/05/04 13:41 <DIR> aiuto 2014/05/04 13:41 <DIR> Immagini 13/07/2013 05:36 2.200 Informazioni.txt 2014/05/04 13:41 <DIR> lingue 2014/05/04 13:41 <DIR> languages_eobd2 13/07/2013 05:36 122,880 multiROM.bak.dll 13/07/2013 05:36 122,880 multiROM.dll 13/07/2013 05:36 74,240 README_SETUP.doc 13/07/2013 05:36 10,499 README_SETUP.TXT 2013/06/07 22:51 412 regkey.dat 13/07/2013 05:36 2.347 TABELLA Corrispondenza EPROM.EEPROM.txt 13/07/2013 05:36 60,928 TAB_COMPARAZIONE_EPROM_Service_Bosch.doc 2014/05/04 13:41 55,094 unins000.dat 13/07/2013 05:36 717,985 unins000.exe 2014/05/04 13:41 utente <DIR> 22/04/2013 23:05 165,376 Win 7.exe 13/07/2013 05:36 1.437.696 winmap.exe 27 File 21.158.925 byte 11 Directory Disponibili byte 742.664.269.824 Se si rimuove regkey.dat , sw non si avvia, se si esegue sw con non congruenti regkey.dat inizio sw ma non riconosce strumento. Questa exe ? protetto con WinLicense, molto esay per rimuovere, ora sto lavorando su di esso per soluzione di lavoro offerta ~~~~~~~a per tutti gli utenti dk [/ QUOTE]






















































:top:


Hello I tried to install the installer FGTech V54 but does not open the software on windows 7 xp that some of you have to post the exact regkey.dat and the dll to start it? Thank you so much.

bubu55
6th April, 2014, 09:13 PM
:top:

Hello I tried to install the installer FGTech V54 but does not open the software on windows 7 xp that some of you have to post the exact regkey.dat and the dll to start it? Thank you so much.


Regkey is generated on your hw id

infinityecu
7th April, 2014, 12:56 AM
[QUOTE = bubu55; 2270231] Regkey ? generato sul vostro id hw [/ QUOTE]

But for it to work you could give me the key generator and the dll to start the application eobd2.exe? Thanks in advance ....... : Top:

bubu55
7th April, 2014, 08:17 AM
[QUOTE = bubu55; 2270231] Regkey ? generato sul vostro id hw [/ QUOTE]

But for it to work you could give me the key generator and the dll to start the application eobd2.exe? Thanks in advance ....... : Top:

yes, you need keygen or.... :pirate:
I'm working for free solution, winlicense is easy :D

eduzgz
7th April, 2014, 09:14 PM
Anyone knows how to read an ECU Siemens Sid208 for a ford transit year 2012?
I can't find any info about.
Thanks


Sent from my iPhone using Tapatalk

cp2010
7th April, 2014, 10:18 PM
check email

eduzgz
8th April, 2014, 04:33 PM
Anyone knows how to read an ECU Siemens Sid208 for a ford transit year 2012?
I can't find any info about.
Thanks


Sent from my iPhone using Tapatalk
Ok I can connect but I can't read, the flash it's protected, any idea?
Thanks

sinan33
9th April, 2014, 07:49 AM
You should try the Password tool to read this ecu.You have a little luck to get the pw.
But original and up to date galletto can read/write this ecu.

eduzgz
9th April, 2014, 08:37 AM
You should try the Password tool to read this ecu.You have a little luck to get the pw.
But original and up to date galletto can read/write this ecu.

I did try with the password tool and say,
"no password found, we working on it" or something similar, I can't remember now, I saw the original tool can do it, I think it's only a software problem, need to be up to date to add these passwords.

Thanks for reply


Sent from my iPhone using Tapatalk

bubu55
9th April, 2014, 02:45 PM
**********

infinityecu
9th April, 2014, 02:58 PM
Hello, you can post the solution to run without bugs, the cockerel FGTech on windos xp and windows 7?

Thanks in advance...........

sinan33
9th April, 2014, 05:58 PM
**********
What is **********?
:o

bubu55
10th April, 2014, 09:13 PM
Solved problem for run Fgtech V53 china clone in windows 7 32 and 64 bit witouth bugs and witouth date change.
Update available

Screen attached

gttuning
10th April, 2014, 10:20 PM
What is **********?
:o
its***********:):)

robytza
11th April, 2014, 12:02 AM
Bubu i'm using v54 from car-prog in the same way :)

Dobermann
11th April, 2014, 01:31 AM
so hello friends,

short update about My Galletto V54 Eu from Austria and simos PCR2.1

My Galletto broke the ecu from the Golf6 with pcr2.1, the car was by the Vw dealer and they changend all crankshaft sensors and have a look at the ecu harrness. all ok !

next step was new simos ecu ! now the fault is gone !

I think it is old v54 software ! in this video you can see eeprom function for read/write >>> https://www.youtube.com/watch?v=ccBFvPfm5Ds

this is galletto aes v54

im really angry about that !! one point to buy this galletto was pcr2.1

bubu55
11th April, 2014, 08:05 AM
so hello friends,

short update about My Galletto V54 Eu from Austria and simos PCR2.1

My Galletto broke the ecu from the Golf6 with pcr2.1, the car was by the Vw dealer and they changend all crankshaft sensors and have a look at the ecu harrness. all ok !

next step was new simos ecu ! now the fault is gone !

I think it is old v54 software ! in this video you can see eeprom function for read/write >>> https://www.youtube.com/watch?v=ccBFvPfm5Ds

this is galletto aes v54

im really angry about that !! one point to buy this galletto was pcr2.1

This is not aes....
This video is uploaded by myself and i can assure this is not aes tool ;)

chipauto
11th April, 2014, 08:25 AM
Fgtech v54 - Pcr 2.1 unlock vers 54 unblock by obd2

sinan33
11th April, 2014, 08:43 AM
Fgtech v54 - Pcr 2.1 unlock vers 54 unblock by obd2


How can you unlock pcr2.1 by obd using galletto v54?

Tjur
11th April, 2014, 05:21 PM
I plan to buy galletto clone from FGTECH GALLETTO 3 V54 (http://tunertool.com/)
If somebody made by this one DCM3.7 on Ssang Yong?
Read by OBD and write by JTAG ?

eduzgz
11th April, 2014, 06:54 PM
How can you unlock pcr2.1 by obd using galletto v54?

Simply couldn't
Need to do as usual, unlock first by serial, after unlock read the ECU by serial as well and writing need to be done by obd, even in the 2014 original version, so no changes at all in any tool.
Probably was an English language confusion? I hope so ;-)


Sent from my iPhone using Tapatalk

Dobermann
12th April, 2014, 03:04 AM
This is not aes....
This video is uploaded by myself and i can assure this is not aes tool ;)

hello ok what tool is that ??

what update do you have for galletto eu ??

br

bubu55
12th April, 2014, 09:28 AM
hello ok what tool is that ??

what update do you have for galletto eu ??

br

This tool is produced by mine and in this video you can see in background my lab where i test the instruments before ship to my clients.

AlexandruP
12th April, 2014, 09:44 AM
I plan to buy galletto clone from FGTECH GALLETTO 3 V54 (http://tunertool.com/)
If somebody made by this one DCM3.7 on Ssang Yong?
Read by OBD and write by JTAG ?

Yes with tunertool.com V54 clone ;)

mugatu
12th April, 2014, 09:50 AM
I am interested in the software update v54 FGTech to use my galletto without date change without dongle.

tunertool
12th April, 2014, 09:54 AM
Fgtech v54 - Pcr 2.1 unlock vers 54 unblock by obd2



Unlock only via boot mode for PCR 2.1 I made one using my clone yesterday!

theghost
12th April, 2014, 01:13 PM
Dear doberman -> pls post a picture of your hardware -> as far i know you have updated fw48 but not real fw54 hw.

Dobermann
12th April, 2014, 06:17 PM
Dear doberman -> pls post a picture of your hardware -> as far i know you have updated fw48 but not real fw54 hw. With austrian fw54 clone pcr2.1 works normally flawless

hello theghost ! yes i have updatet fw48 to fw54.

but that helps me not for the moment ! my galletto crashed the simos pcr2.1 for sure !! i have done only the unlock with my galletto and after that the fault comes up !

i can send you a pic from the inside of my galletto no problem !


vw solved the problem with NEW ecu !

theghost
12th April, 2014, 06:19 PM
Then most likely you have damaged the ecu while opening or soldering the wires.

robytza
12th April, 2014, 07:41 PM
How can you unlock pcr2.1 by obd using galletto v54?

i have unlocked & flashed continental pcr 2.1 with galletto v54 from car-prog without problems.

sinan33
13th April, 2014, 09:17 AM
Of course you can but; you can't unlock it over obd.
You can read it over obd,unlock using boot mode then you can write it over obd again.

robytza
13th April, 2014, 09:41 AM
All tools are unlocking in boot mode.
do you know one that is doing this on obd ?

sinan33
13th April, 2014, 10:21 AM
Fgtech v54 - Pcr 2.1 unlock vers 54 unblock by obd2


I don't know but i guess this guy knows :)

eduzgz
13th April, 2014, 10:26 AM
All tools are unlocking in boot mode.
do you know one that is doing this on obd ?

The original tool can unlock by obd the ECU Siemens sid208 in Ford, but need to be read by boot and also can be unlocked by boot( I tried with a clone but it's no capable to unlock this ECU at any way )
This is only info, you will need to remove the ECU anyway.
Cheers


Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 10:32 AM
Did you try to get pw from obd on edc17 pw protected ecus?

eduzgz
13th April, 2014, 10:33 AM
Did you try to get pw from obd on edc17 pw protected ecus?

No, I don't know if that it's possible


Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 10:37 AM
someone has told me that it is possible to get the pw over obd; i will test it when a car with edc17 pw protected ecu arrives to workshop.

eduzgz
13th April, 2014, 10:42 AM
someone has told me that it is possible to get the pw over obd; i will test it when a car with edc17 pw protected ecu arrives to workshop.
There is the manual of the 2014 version
255462


Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 10:45 AM
I think it's time to find a new clone tool because galletto can't be cloned no longer.

eduzgz
13th April, 2014, 10:52 AM
I think it's time to find a new clone tool because galletto can't be cloned no longer.

Yes, probably Kess + K Tag may be cloned well ( no Chinese ), with that you cover all, the problem is that Alientech had remove the tricore option in the new Kess and put it on ktag, so my Kees it is pure obd, still being a very good tool.
CMD should be ideal because have all in one, but I think have a similar problem like galletto, need Internet connection ( I'm not sure about it )



Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 11:01 AM
Yes, cmd needs internet connection.
Kess and K-tag are good tools, but there are not any news about new clones of them.

eduzgz
13th April, 2014, 11:06 AM
Yes, cmd needs internet connection.
Kess and K-tag are good tools, but there are not any news about new clones of them.

I think car-prog is working on it and I saw a Kess v2 with 2.02 software, I didn't pay too much attention because I've the original and know I don't know the web , maybe was car prog I don't know


Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 11:09 AM
I think so but i have asked him about the new clones he told me that he just has the projects he didn't make any tools yet.

eduzgz
13th April, 2014, 11:14 AM
Well I hope he can do a good tool soon.
By the way, I've a smart for two 1.0 turbo petrol year 2012 to remap it in my garage, can be done with the usual tricore right ?
I check it on ksuite, but it's 2.05 version, so I am not sure about it.


Sent from my iPhone using Tapatalk

sinan33
13th April, 2014, 11:29 AM
Yes, you can do it with tricore.

eduzgz
13th April, 2014, 11:51 AM
Yes, you can do it with tricore.

Do you have the diagram?
I can't find it.
The ECU it's a Bosch ME7.7.0 ST10F275
Should be boot st mode no tricore
Thanks


Sent from my iPhone using Tapatalk

robytza
13th April, 2014, 12:04 PM
hey guys.... here the discussion is about anything else you are talking about.
tuning trainings and how-to's are on others topics

sinan33
13th April, 2014, 12:04 PM
Do you have the diagram?
I can't find it.
The ECU it's a Bosch ME7.7.0 ST10F275
Should be boot st mode no tricore
Thanks


Sent from my iPhone using Tapatalk
MCC_Smart_Bosch_ME770_Platine.rar - Speedy Share - upload your files here (http://speedy.sh/rpmEz/MCC-Smart-Bosch-ME770-Platine.rar)

sinan33
13th April, 2014, 12:05 PM
I hope this helps you.

gery11
15th April, 2014, 08:45 AM
Hi guys,
I have got fgtech mini from cp. It works very good.
Tested a few ecu's and read/write ok

And thanks to @robytza soft it is working perfectly on win 7 64 bit.
Really nice guy, thanks again!

robytza
15th April, 2014, 09:00 AM
you`re welcome my friend !
glad to be able to help you.

sinan33
15th April, 2014, 02:05 PM
you`re welcome my friend !
glad to be able to help you.
Which software of robytza?
Do you have a software for v54 which can work on windows 7 without changing date?

robytza
15th April, 2014, 02:14 PM
yes....already delivered to car-prog.
ask him to provide you the sw if you bought from him

sinan33
15th April, 2014, 02:19 PM
Yes, my tool is from him.Can it work without usb dongle?
Thank you.

robytza
15th April, 2014, 02:25 PM
no. still works with dongle.
but you dont need anymore to exchange drivers or date....
just click and run on xp and 7 32 or 64 bits after you have plugged in the interface and dongle.
ask him to give also the x64 driver for it.
i also provide that to him.

sinan33
15th April, 2014, 02:28 PM
no. still works with dongle.
but you dont need anymore to exchange drivers or date....
just click and run on xp and 7 32 or 64 bits after you have plugged in the interface and dongle.
ask him to give also the x64 driver for it.
i also provide that to him.
Thank you very much; i have sent an e-mail to him for a few minutes ago.