Carprog Opel can read problem

[hackerabcd]

I have carprog china clone . It won't read any Opel can bus ecus . Is any known faults with not reading can bus

regards
peter

[adrianvip]

Hello
you should lok at the A1 adapter chinese have make a bad copy you should change the resistors like on the photo :

233808233809

[catala20032004]

adrian can you explian better first replacement and last i understood, but the one in the middle what did you replaced?

[Wodzu]

What value has a yellow R1? I lost it. It is the same as the R4?

[jaelgti]

What value has a yellow R1?
thanks

[jaelgti]

R1=10K
R2=10K
R3=10K
R5=1K

[scoot]

had same fault i bought 3 none do opel got repair kit from code card and perfecto

[jaelgti]

Hi today I tried but it did not work.
scoot, you explain better, I do not understand what you mean.
thank you very much

[gadroulll]

wrong place in resistor and capacitor , maybe in the swap you must check the correct value of the resistor , if you lose connection while reading you must change the capacitors . for better look information check the original site for repair it has photos of the adapter

[wiseman]

Is this the same problem for reading IMMO on Megane 2 for keycard programming?

[gadroulll]

if you use the adapter a1 yes it is

[Wodzu]

I fixed that in this way and it works Opel CAN.

[forumoto]

I fixed that in this way and it works Opel CAN.


Hey, the question i want to ask is that, WHEN you CHANGE the big IC MCP2515, in the clone adapter, how do you update it so that it will work, because seemly like when you change that IC, you will need to update the A1 adapter and knowing well this is clone, it can harm the unit...

[radsky]

it`s A1 adapter so don`t need any update.

[forumoto]

it`s A1 adapter so don`t need any update.


once more time, because i read from some place that when such IC is changed, the A1 adapter need to be updated...

[Tusznioo]

Hi, I bought carprog 4.1 china and can not be combined with dashboard a CAN adapter a1 already reworked a1 resistors but still does not work,What else can I do?

[ruffles1986]

Hi, I bought carprog 4.1 china and can not be combined with dashboard a CAN adapter a1 already reworked a1 resistors but still does not work,What else can I do?
Test +12V on transistor pin (see photo posted here http://www.digital-kaos.co.uk/forums/f155/carprog-opel-can-read-problem-383567/#post2266905 ) and check resistor values and not swaped resitors with capacitor. If all is ok replace MCP.
P.D. A1 adapter not work with VW CAN ecus

[Tusznioo]

12v transistor is on, check for can fiat ducato 2007 dashboard, which does not replace the resistor with a capacitor in a1?

[ruffles1986]

12v transistor is on, check for can fiat ducato 2007 dashboard, which does not replace the resistor with a capacitor in a1?
See photo and see your adapter, some a1 adapters clone have swapped place resistor with capacitor. for now i not use carprog for ducato dash... maybe you need Fiat adapter female to male, or maybe fiat adapter is wrong, check it

[tango]

once more time, because i read from some place that when such IC is changed, the A1 adapter need to be updated...

you have read wrong my friend, that info is for the A1+ adapter not the A1 adapter
A1 adapter needs no update

[forumoto]

which of the adapter is for OPEL CAN? is it not the A1?

[ruffles1986]

which of the adapter is for OPEL CAN? is it not the A1?

For Opel Can use Adapter A1

[tango]

which of the adapter is for OPEL CAN? is it not the A1?

yes it is the A1 but only after all the repairs have been done to it

[gadroulll]

search on the original site and you will see how to repair it

[rdu04]

what version opel CAN work?