BMW E53 / X5 - faulty dash ?

[CARPARTS]

Hi

BMW X5 - 2005. With original dash, all needles goes, but control lights doesn't work (blinking lights etc...)
Also radio doesn't work

Putting a second hand dash (with another VIN number), all control lights from dash work, also radio works now...

Can a faulty (?) dash shut down the radio in this BMW ? And shut down also the steering-wheel-servo ?



2e question ; when radio works, i get radio-screen with the next message :
Can anyone explain what this message means and what's the purpose of this ?


232429

[smartymarti]

Screen lock is in settings and code can be found in handbooks or a user defined one, find some one with relevent diagnostic gear ie icom and reconfigure

[markony79]

write 0000 code and its work

[CARPARTS]

Indeed, 0000 is working, but is it possible that a faulty dash can shut-down the radio ?

[TULGEYWOODMAN]

Hi

BMW X5 - 2005. With original dash, all needles goes, but control lights doesn't work (blinking lights etc...)
Also radio doesn't work

Putting a second hand dash (with another VIN number), all control lights from dash work, also radio works now...

Can a faulty (?) dash shut down the radio in this BMW ? And shut down also the steering-wheel-servo ?



2e question ; when radio works, i get radio-screen with the next message :
Can anyone explain what this message means and what's the purpose of this ?


232429

Was this after you played with it or did it arrive like that?

Sometimes, if you programme by soldering to back of board, you can disturb solder connection on the smd that you soldered to. This can make dash dead.

[CARPARTS]

Was this after you played with it or did it arrive like that?

Sometimes, if you programme by soldering to back of board, you can disturb solder connection on the smd that you soldered to. This can make dash dead.

Nope, was coming in like that. Nobody even touched this odometer.

[baze007]

Hi

BMW X5 - 2005. With original dash, all needles goes, but control lights doesn't work (blinking lights etc...)
Also radio doesn't work

Putting a second hand dash (with another VIN number), all control lights from dash work, also radio works now...

Can a faulty (?) dash shut down the radio in this BMW ? And shut down also the steering-wheel-servo ?



2e question ; when radio works, i get radio-screen with the next message :
Can anyone explain what this message means and what's the purpose of this ?


232429



What you see on screen will protect the radio ..... if you modify your code vehicle will not start at the same time activates the alarm

[rukartinatv]

What you see on screen will protect the radio ..... if you modify your code vehicle will not start at the same time activates the alarm
so how to fix this problem?
I have thaseme problem i wright dump from another E53 thaseme sw and hw version but when i plug dash alarm activates and car dont start.
Do you know how to fix it?
Thank You

[CARPARTS]

so how to fix this problem?
I have thaseme problem i wright dump from another E53 thaseme sw and hw version but when i plug dash alarm activates and car dont start.
Do you know how to fix it?
Thank You

I solved this issue

With the original dash, radio don't work, steering assyst don't work..... and all (led) lights in the dash from control like blinking lights, beam, park etc
-lights in the dash DON'T light up when its activated.

So i changed the dash with another dash from another x5, and all lights work, radio work, all oke
BUT the alarm start indeed to work also, unless you put the code "0000" in the radio-screen.
(i didn't change the VIN number yet)

When i changed the vin number to the original vin-number from car, ALL work perfect.
(you only need to adapt (IKE-EWS) with PA-SOFT or similar software)


Writing another dump will not help. You need to change the complete dash by some second hand.
So its some hardware fault INside the dash itselfs

fault = "I-line dash faultly" according PA-soft



hope this help you out

[rukartinatv]

I solved this issue

With the original dash, radio don't work, steering assyst don't work..... and all (led) lights in the dash from control like blinking lights, beam, park etc
-lights in the dash DON'T light up when its activated.

So i changed the dash with another dash from another x5, and all lights work, radio work, all oke
BUT the alarm start indeed to work also, unless you put the code "0000" in the radio-screen.
(i didn't change the VIN number yet)

When i changed the vin number to the original vin-number from car, ALL work perfect.
(you only need to adapt (IKE-EWS) with PA-SOFT or similar software)


Writing another dump will not help. You need to change the complete dash by some second hand.
So its some hardware fault INside the dash itselfs

fault = "I-line dash faultly" according PA-soft



hope this help you out

(you only need to adapt (IKE-EWS) with PA-SOFT
Can you explain how to do it with pasoft?
Thank You for your help

[CARPARTS]

you put the second hand dash inside the car
you go with that v1.40 pa soft to "IKE"
then to "coding"
then you see "list" from "IKE - EWS" and some "EWS to IKE" and some more items.....
choose the "ews to ike" menu (not the other)
then it does automatic the coding
done

now you will see also ion "car identification" the info filed is not RED color anymore which means its now adapted to the car

[rukartinatv]

you put the second hand dash inside the car
you go with that v1.40 pa soft to "IKE"
then to "coding"
then you see "list" from "IKE - EWS" and some "EWS to IKE" and some more items.....
choose the "ews to ike" menu (not the other)
then it does automatic the coding
done

now you will see also ion "car identification" the info filed is not RED color anymore which means its now adapted to the car
Thank you so much for you help!!!'

[nomis]

Thank you so much for you help!!!'

rukartinatv .... you forgot a button lol ...

[se93]

Does EWS to IKE also code the VIN?


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)

[CARPARTS]

I changed VIN already manually before I did this "EWS to IKE programming" , so i don't know.