2003 E65 Cas flash file please

[jonny r]

Hi,


I have a 2003 E65 730d sport for mileage correction. Problem is that when reading the cas via can100 connection the flash has somehow got damaged and car is now dead. I can no longer get comms with cas via obd. I took cas out and went to read with rosfar and I see that the pin out connections in rosfar pdf are for a different board than mine. I checked several different pdfs from various different cas programmers, ie, R270 programmer, AK500, etc... but none of them had the same board as my cas, I decided today to remove the pcb from cas by desoldering various different points on the board, then I had access to the other side of board where 9s12 is located. This allowed me to trace back from the processors pins the solder connections to use with my rosfar programmer. I have now read the 0K50E processor and loaded the eeprom file into my tango. Tango accepts the eeprom dump so I am now thinking that the eeprom must still be ok and it is just the flash that has got damaged. I have attached a photo of the cas part number etc.


I would be very grateful if someone could please upload a flash file for this cas, or a recovery file from rosfar, or even a flash file from this type of early E65 cas. I use genuine xprog and rosfar. any files read by these programmers i can work with.


Thank you all for your time.


Kind regards


Jonny

[teerak2uk]

If all else fails I think there is one on the bay

[nomis]

You need a search ... http://www.digital-kaos.co.uk/forums/f174/e65-2006-cas-need-connection-rosfar-294994/#post2017831

[jonny r]

You need a search ... http://www.digital-kaos.co.uk/forums/f174/e65-2006-cas-need-connection-rosfar-294994/#post2017831

Thanks mate, but I need a flash file for this cas. I don't suppose you still have the recovery flash file saved on your computer from reading that cas in your thread?

Thanks again for your help with this

Jonny

[nomis]

I took cas out and went to read with rosfar and I see that the pin out connections in rosfar pdf are for a different board than mine. I checked several different pdfs from various different cas programmers, ie, R270 programmer, AK500, etc...

I talk about this.. here is flash read with rosfar .

[markony79]

"jonny r"

where are you from ?
post the flash and eeprom here
maybe can fix it :)

[jonny r]

I talk about this.. here is flash read with rosfar .

Thank you very much nomis :)) I will try flash and report back shortly. Thanks again :))

[jonny r]

"jonny r"

where are you from ?
post the flash and eeprom here
maybe can fix it :)

Thank you Markony79 for your interest, i am from Belfast. I will try this flash read by rosfar that nomis has kindly uploaded first and i will report back results. Thanks to everyone for your help :)

[nomis]

If you need eeprom also, i can send to you or any format you want like xprog r270 etc........... just let me know

[jonny r]

Hi nomis, i tried your rosfar flash file and it shows me "verify error" when it finishes. When i program my own recovery flash back to cas rosfar shows me "Successfully Programmed" message. I noticed from your picture mate that your hardware number is different than mine. My hardware number is 6935611 and your hardware number is 6922649 also the boards are different. I will go to workshop now and get my laptop and post my original flash file for you to have a look at. Again, thank you very much for your help with this.
Jonny

[nomis]

Yes you right .. mine is different. So you believe your flash is corrupt ? Then you need same part no.. which i have not ..sorry .

P.S. so wait someone give you same as you need..

[jonny r]

232861
Hi,

attached is my original damaged flash read with rosfar, also i have attached again the photo of cas for reference part#

Many thanks

Jonny

[nomis]

Whats up mate ? no one send you what you need ! lol ..................................

[jonny r]

Whats up mate ? no one send you what you need ! lol ..................................

No mate, i ended up buying cas with same part# from ebay :( Just have to wait now for it to arrive. Thanks for your interest.

bmw E65 start button 61.32-6 935 611 | eBay (http://www.ebay.co.uk/itm/bmw-E65-start-button-61-32-6-935-611-/281211963238?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item41798a0766)

[hauwkee]

what u need to do after adapt sync cas to ecu/dme

[Rtronics]

if your eeprom data is good, just copy eeprom only to your new cas. all will be good no sync nothing.it will work. i did e60 the other day. good luck.