View Full Version : galletto 3 v54 euro clone with edc17cp14
ricards99
10th December, 2013, 12:45 PM
hi,
i have probleme with galletto 3 v54 european clone
i connect in boot mode with ecu vw jetta 2009 edc17cp14 soft version begin with 10373 ( not t-prot)
read without probleme but in writing eprom no problem but internal flash dont accept, all time say checksum not supported must do on line
i say ok or cancel same, stop the procedure
i try to write back original and same thing dont accept write internal flash
this is what i have in identification pannel when i do connect
Infineon Tricore TC1796
CPU-ID=0000182000008A02
Internal Flash ID = 0031C002
Internal Flash 2048Kb Protected
OTP Protect: 0x10000 -- 0x13FFF
OTP Protect: 0x14000 -- 0x17FFF
External Flash Spansion S29CD016GB
...]o;..7.
..........
EEprom 128Kb Protected
BR
bubu55
10th December, 2013, 03:12 PM
Send mod file and i reallocate rsa for correct writing with fgtech
ricards99
10th December, 2013, 04:12 PM
there are files ori and fap off without checksum correction
thanks in advance
bubu55
11th December, 2013, 01:47 AM
Attached.
Pass in pm
ricards99
17th December, 2013, 08:55 AM
always same problem, is it possible my galletto have problem?
it's a european clone v54
with edc17cp10 psa no problem read/write but with this cp14 vag not work even in bootmode and obd ( read ok in both) , i have not another ecu to test,
have someone do this ecu with galletto euro clone?
i ask the seller and he say me the dpf is in external flash ( !!!!!!) i ask for problem dont write and he talk about position of dpf data in ecu
ipejasinovic
17th December, 2013, 10:10 AM
CP14 shouldn't be problem on Tricore boot. I think you have broken ECU or device.
mario38
17th December, 2013, 10:21 AM
hi,
i have probleme with galletto 3 v54 european clone
i connect in boot mode with ecu vw jetta 2009 edc17cp14 soft version begin with 10373 ( not t-prot)
read without probleme but in writing eprom no problem but internal flash dont accept, all time say checksum not supported must do on line
i say ok or cancel same, stop the procedure
i try to write back original and same thing dont accept write internal flash
this is what i have in identification pannel when i do connect
Infineon Tricore TC1796
CPU-ID=0000182000008A02
Internal Flash ID = 0031C002
Internal Flash 2048Kb Protected
OTP Protect: 0x10000 -- 0x13FFF
OTP Protect: 0x14000 -- 0x17FFF
External Flash Spansion S29CD016GB
...]o;..7.
..........
EEprom 128Kb Protected
BR
maybe your problem is this "External Flash Spansion"
if you try to write files golds this work?
off your fap fap I think it is wrong must be disabled by switch
ricards99
17th December, 2013, 11:13 AM
CP14 shouldn't be problem on Tricore boot. I think you have broken ECU or device.
for ecu the car start without any problem
for the device edc17 cp10 psa read write without problem
with this cp14 eprom read write without problem
?????? but when i try to write internal flash it say checksum not supported you must contact fgtech
just one info someone before me had read this ecu with k-tag clone but he had not try to write
mouaoued
19th February, 2014, 06:11 PM
dump is corrompu edc 17cp14 golf6
AlexandruP
19th February, 2014, 06:16 PM
From where did you buy your clone?
Fantomisback
19th February, 2014, 07:47 PM
Are u try write all beckup file u read?
i mean on int.flash ext.flash and eprom
then after that just try write int.flash
mouaoued
20th February, 2014, 03:30 PM
edc17cp14
Is it not External Flash
read mpps v13 fg galletto v52
ecu rejected checksum
kire106ka
20th February, 2014, 04:53 PM
Try to write original flash back the dpf file you have is shit and the tool you have must have some problem
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.