View Full Version : Audi A4 2.0 CR EDC17
BrunoPT
23rd December, 2013, 10:47 AM
Hello,
I have here a audi A4 2.0 CR EDC17, that is to override fap, however eliminated by Switch (file below) but still with 2 errors related.
Can anyone help me delete these DTCs?
The errors are:
2 Faults Found:
8621 - Sensor 1 for Exhaust Temp Bank 1 (G235)
P0544 00 [040] - Circuit Malfunction
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 63
Mileage: 198126 km
Date: 2013.11.29
Time: 14:42:24
5260 - Sensor 1 for Exhaust Temp Bank 1 (G235)
P0544 00 [040] - Circuit Malfunction
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 179
Mileage: 198126 km
Date: 2013.11.29
Time: 14:42:19
I leave here the original and fap off by switch :)
I appreciate your help
ominimicu
23rd December, 2013, 11:20 AM
Switch method requires all sensors conected and working, any fault you got will still appear. so now you need to dlete DTCs or replace snesors
digi men
23rd December, 2013, 11:21 AM
hy
try this now 236216
digi men
23rd December, 2013, 11:27 AM
on your file was wrong cheksum i have not deleted the dtc and if _ominimicu (http://www.digital-kaos.co.uk/forums/members/133668-ominimicu/) say so than beliwe him ;)
BrunoPT
23rd December, 2013, 11:27 AM
Switch method requires all sensors conected and working, any fault you got will still appear. so now you need to dlete DTCs or replace snesors
Yes, I know to switch all sensors should be ok, but in this case it is to eliminate sensors. (dts)
thanks mate
BrunoPT
23rd December, 2013, 11:31 AM
hy
try this now 236216
your file is what I shared with switch off
digi men
23rd December, 2013, 11:43 AM
yes i know but i not remember witch was wit no good cheksum,can be that the other than was, i have i case put this than here !
morgano
23rd December, 2013, 12:21 PM
Hello @BrunoPT
Here you have. Hope it saves your day ;)
Regards,
k0mpresd
24th December, 2013, 10:29 AM
maybe this can help. (addresses do not match your specific file but should be close. with a bit of common sense you can sort for yourself).
deleting individual dtc codes from edc17 (cp14 was the flavor i was working with)
example:
009298 - Diesel Particle Filter; Differential Pressure Sensor
P2452 - 000 - Elect. Malfunction - MIL ON
find the p code in the p code look up table. 16bit, hex.
location: 190a7a
p code table start: 190654
get your hex calculator!
190a7a - 190654: 426. divide by 2, 213.
find your vag specific dtc look up table. 8 bit.
example:
table start location: 18569e
18569e + 213: 1858b1. this is the location of the p2452 dtc. 00 this byte.
no more dtc light.
same process as me7 except /2 instead of /8.
chli1976
24th December, 2013, 12:52 PM
I have seen that in other forum, do you have the right file for this instructions
k0mpresd
24th December, 2013, 01:17 PM
I have seen that in other forum, do you have the right file for this instructions
yes? those are my instructions. sorted that formula for myself one day after needing to delete a few dtc's from a customer cp14 ecu.
having the corresponding ori file takes a bit of the fun out of the search and guessing to learn dont you think? ;)
the edc17 (and med17) tables arent much different than me7. find one and you found them all.
anyways, ori file attached. merry christmas. :positive:
chli1976
24th December, 2013, 01:41 PM
Many thanks K0mpresd
Here an exel file for calculate
236400
k0mpresd
24th December, 2013, 02:21 PM
Many thanks K0mpresd
Here an exel file for calculate
maybe an english version? :)
chli1976
24th December, 2013, 02:37 PM
Ok i will do it, but my english is not so good
k0mpresd
24th December, 2013, 02:38 PM
Ok i will do it, but my english is not so good
well my "anything other than english" is not so good. :p
chli1976
24th December, 2013, 02:53 PM
Have a look
236410
k0mpresd
24th December, 2013, 03:00 PM
Have a look
better. thanks.
morgano
24th December, 2013, 03:10 PM
Hmm, i just did BrunoPT file using the so famous EDC17 Tiguan D@mos and figuring out locations on his file. :)
morgano
25th December, 2013, 02:00 PM
@BrunoPT
Did you have chance to flash the file? Have not received your pm with result ;)
Regards,
BrunoPT
25th December, 2013, 02:20 PM
Friend i will test tomorow. I post the results :) merry cristmas
Enviado do meu GT-I9505 atrav?s de Tapatalk
BrunoPT
27th December, 2013, 07:48 AM
Hello morgano. I tested the file and working good. Thanks friend
Enviado do meu GT-I9505 atrav?s de Tapatalk
morgano
27th December, 2013, 09:23 AM
Happy new year ;)
Regards,
darius89
29th June, 2015, 08:49 PM
Hi, what type of exel you use. My exel dont recognise.
Hamai
27th October, 2016, 09:39 AM
Have a look
236410
what did you mean write "table start location" ? Start table of switch ?
chli1976
27th October, 2016, 02:56 PM
1. column adress from error code (e.g P0401)
2. start adress from errors
3. start adress from switches
belka163
6th September, 2021, 05:36 PM
GOOD PAGE SWEET INFOS
belka163
6th September, 2021, 05:37 PM
KEEP DOING
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.