View Full Version : Adapt VW brand new micronas dash 2008
z786
27th January, 2014, 08:10 PM
Hi can someone guide me on how to adapt a brand new dash into a VW please?
done 100s of used but never a new one
thanks
r6eck
27th January, 2014, 08:20 PM
Last one I did just swapped baby board from old to new
z786
27th January, 2014, 08:27 PM
original is burnt to a crisp :(
chriskross
27th January, 2014, 08:30 PM
i also never have done it :-) but i think you just need PIN of car for adaption
Fec001
27th January, 2014, 09:47 PM
Immobilizer IV Immobilizer Swapping (Instrument Cluster) - Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Immobilizer_IV_Immobilizer_Swapping_(Instrument_Cl uster))
did you try this?
yugo45
28th January, 2014, 12:05 AM
Immobilizer IV Immobilizer Swapping (Instrument Cluster) - Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Immobilizer_IV_Immobilizer_Swapping_(Instrument_Cl uster))
did you try this?
This will not work on 2008 Dash.
yugo45
28th January, 2014, 12:10 AM
original is burnt to a crisp :(
can you read Micronas and eeprom form old dash or everything is burnt?
Fec001
28th January, 2014, 12:16 AM
This will not work on 2008 Dash.
2008 is immo gen IV. isn't that?
z786
28th January, 2014, 01:06 AM
i have access to original pin and cs, need to know how to change adaption to mode 6
z786
28th January, 2014, 01:59 PM
any1??????
yugo45
28th January, 2014, 07:14 PM
2008 is immo gen IV. isn't that?
Correct but immo 4 C , VCDS does not support Immo 4 C
yugo45
28th January, 2014, 07:17 PM
i have access to original pin and cs, need to know how to change adaption to mode 6
You will also need MAC, VIN and Immo number, which can be found in ECU.
Read New dash with X-prog Flash and eepom and post here.
Can you do this?
z786
28th January, 2014, 10:50 PM
i can try. i have acces to avdi full i got this, 1 is from dash other from ecu
yugo45
29th January, 2014, 09:49 AM
If you can read it with AVDI eeprom and flash will work as well.
Also it would be best if you can read eeprom and flash from old cluster, I know you said is burn but is it possible to get eeprom and flash form it?
z786
29th January, 2014, 10:06 AM
no old 1 is completely fcuked up, i'l send a pic later lol
so how do i do it with avdi then?
yugo45
29th January, 2014, 10:25 AM
I do not know with AVDi , but with X-Prog you can read Flash and eeprom .
Do you have X-Prog?
z786
29th January, 2014, 10:37 AM
i have xprog, but i can access new clocks immo block via obd no problem
chriskross
31st January, 2014, 06:32 AM
Write pin vin mac cs and powerclassfrom engine ecu in cluster, Programm new key with tag keytool, change immostatus to 6
alpha-music
17th February, 2014, 03:28 PM
can anybody tell me login code from this microcans eprom... i need to learn new dash246077
yugo45
17th February, 2014, 10:53 PM
can anybody tell me login code from this microcans eprom... i need to learn new dash246077
You need to read Flash + Eeprom not just eeprom.
Meat-Head
18th February, 2014, 08:50 AM
If your desprate often dealer 'only' charge 45 sodds ring them
How did dash get fried?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.