PDA

View Full Version : EDC16C34 CODE P0603



ivanimpalea
14th February, 2014, 11:45 AM
ciao a tutti! Ho un problema che ho letto in un BDM ECU ec16c34 una citroen c4 picasso 1.6 hdi 110 cv dpf / egr off, una volta scritta modificato regolarmente ricevo la luce mil su e p0603 codice di errore del computer interno, ho cercato di scrivere il file originale ma il codice di errore rimane, inserire il file, aiuto!

MACKIE
14th February, 2014, 12:17 PM
English please....;)

ivanimpalea
14th February, 2014, 12:40 PM
Forgive hello to everyone! I have a problem that I've read in a BDM ECU ec16c34 a citroen c4 picasso 1.6 hdi 110 bhp dpf / egr off, once written changed regularly get the mil light on and p0603 error code inside the computer, I tried to write the original file but the error code persists, place the file, help!and the attachment to the first post

tonih
14th February, 2014, 12:53 PM
clears dtc by flash, but before please review the file dpf off is wrong

ZIZZOU
14th February, 2014, 08:04 PM
P0603 internal control module keep alive memory(KAM) error
in this memory the ecu store all what he learn from all sensor's engine(egr dpf maf ....ect)
when you disconnect batery this memory is areased
so, you have to restore to zero all adaptations with a diagnostic interface
then drive the car on road (50km), to let the ecu store the new engine adaptations , so the KAM will not be empty
and finaly ,arease the dtc
hope it will help you:smile:

monitel_service
14th February, 2014, 10:18 PM
your file try and report, pass in PM

ivanimpalea
15th February, 2014, 08:55 AM
thanks friend I wrote the file and the error disappeared but the car does not go over 3000 rpm.

tonih
15th February, 2014, 10:51 AM
not just remove the dtc, you must review the dpf

gttuning
16th February, 2014, 09:34 PM
thanks friend I wrote the file and the error disappeared but the car does not go over 3000 rpm.
removing dtc will not take your ecu out of limp mode.

ruffles1986
16th February, 2014, 09:42 PM
Exist a way to reset to 0 the learned values after DPF off?

gttuning
16th February, 2014, 10:57 PM
edc16c34: good file and no problems what so ever.

BrunoPT
17th February, 2014, 12:49 AM
Switch solution working good on this car

didi_du_93000
25th April, 2015, 01:55 PM
Hello, i have same problem.

I have write a IMMO OFF file on ecu just for go to office on road (in limp mode)

After come in office, i have write back original file but always limp mode and DCT P0603.

i have write virgin file and make all adaptation and always same error P0603
i have make DCT off from flash and always limp mode...

Please help me!!!!

didi_du_93000
25th April, 2015, 11:00 PM
problem solved by pinotec.

thanks a lot friend!!!!

codec
27th November, 2018, 12:28 PM
HI
How repair ?
thanks

didi_du_93000
27th November, 2018, 03:49 PM
HI
How repair ?
thanksIf i understand... The eeprom file and flash file is married together. So must sync both file by tuner.
You can't remove the Dtc on table... Don't work.


With Tapatalk