BMW 7 series E65 mileage

[smartymarti]

As long as it's not had the BMW security update you should be able to do cas3/3+ by obd no issues , clock is a bit awkward to remove but EPROM is on rear so no needles etc to remove

[javyb]

Abrites can read cas but cannot write, digiprog asked for ST63 (no OBD).

Will strip dash next week to do the CAS3.

It's cas 2 in BMW 7 series no cas 3. It won't work with digi through cas plug (ST63)

[rukartinatv]

Yes its cas2 but i did one e65 with digiprog st63

[XmoDDeR]

Chip is on front did 4 all on front but used rear solder points digi did the dash tacho did cas

[ttzag]

Hi
Do it on table it's more safer than OBD
Cluster need to remove needles but it's easy, plastic axel.


Sent from my HTC One using Tapatalk 2

[XmoDDeR]

Yes, is CAS2, maybe ST63 can do but seems complicated removing fuses etc.

Might take some time, but will remove CAS and do with R270, I feel safer :)

yes i did all non facelift so no fuse the fuse thing has me too brother i have 2 2006 to do now and dont know if i have to replace chip yet , on 2006 is the chip erasable thanks

[rukartinatv]

If you have right eraser you dont need replace eprom.
The last 2 years i never change eprom.
but i have 3 different erazer
codiprog work 99%
tacho.de eraser work 95%
and from russian company work 100%
e65 you can do from solder points
but for me easy to remove the needles.
cas2 you can do with rosfar

[XmoDDeR]

need rosfar and what russian eraser are u talking about thanks

[rukartinatv]

From mbcleaner but they stop sell them

[XmoDDeR]

cluster easy cas i never did

remove vent careful pry out look to right or left towards pass side dependin on orientation of steering pull the screw and bolt \
two sctrews on top of cluster torx
email me i will return file looking now

[yugo45]

Dash can be done very easy with X-prog. I have done it.

CAS unit is a little pain.A/C vents , Radio and CD , A?c unit has to come out , then CAS unit will come out on the side .

[cokolo]

Any guide to remove cluster and cas ??
Some pictures to help you :joyous:

[aposig]

for cas module .good programmer red rosfar,not kiled flesh,for m35080, good eraser buy from etlweb.com not kiled incremental location!!!

[nomis]

Some pictures to help you :joyous:

Hi mate ! only difficult part is in picture below what tool you use for remove this ? I always damage/scratch..lol

@Gwee
I use R270 for 35080 3/6 V6/VP 080D0WQ always perfect erase, read, write in second's .. & my best tool for secure EIS/CAS R260 red "clone" ....:)

[rukartinatv]

I plan to use r270 for cluster and digiprog for CAS2.
Yiu need st63
dash plug

[XmoDDeR]

hey guys a lil helper for me and us all i was almost there today . Started at the bottom now im ---->http://www.youtube.com/watch?v=yeISkQjdCf4 ------> 2003 bmw 745Li center dash wood trim removal e65 e66 - YouTube (http://www.youtube.com/watch?v=ONBWw_hNVu4) ---------> http://www.youtube.com/watch?v=gmONvTOjMt0 real help just now i was scratching myself bald...:joyous:

[tonyadams5]

I have tried 35080vp on many cars using R270 clone. Blows up the eeprom. Had to replace all of them with new one.

wbr

[XmoDDeR]

i just heard dunno if true r270 original and r270 clone they look alike , mines blown up have to order new

[XmoDDeR]

251788homemade ST63 digi powers up so i know that part is right ....lol:top:

[bersch8688]

How make?

Please post cable connections


Thanks