View Full Version : Polo edc17u01 immo
grzanek85
27th March, 2014, 02:59 PM
Hi,Is it possible immo off for Vw polo 1.4 tdi edc17u01 ? Internal flash and eeprom attached. Thx in advance
Checksum eeprom and flash no problem
horsepower
27th March, 2014, 08:20 PM
hi, you can place the reference to the ECU and year of vehicle.
grzanek85
27th March, 2014, 08:30 PM
VW POLO 2008 1.4 tdi bluemontion ENGINE BWB EDC17u01 045906013E.
Alpinesport
28th March, 2014, 07:01 AM
252639
try it is off
gokey
28th March, 2014, 07:59 AM
CS: 95 2C 97 F3 82 F7 20
PIN: 1274
MAC: C6 9F 70 87
grzanek85
28th March, 2014, 08:25 AM
CS: 95 2C 97 F3 82 F7 20
PIN: 1274
MAC: C6 9F 70 87
it will not do the old ECU destroyed, this dump is new ecu. Thenk's
grzanek85
28th March, 2014, 09:08 AM
252639
try it is off
your file not work
antlio
28th March, 2014, 08:31 PM
Hi
Try this and post results .First correct chm . Pass is in your pm .
regards
umoussa
28th March, 2014, 08:35 PM
I can make it for you by EEPROM, PM me if you need help
grzanek85
29th March, 2014, 09:59 AM
Hi
Try this and post results .First correct chm . Pass is in your pm .
regards
Car start but glow plug lamp blink and error 00558 engine blocked immo
antlio
29th March, 2014, 02:46 PM
The key and the dash is from the same car ?The chm is correct ?
grzanek85
29th March, 2014, 03:54 PM
Yes key and dash org this car, ecu old destroyed in crash .
antlio
29th March, 2014, 06:11 PM
Chm is ok ? What tool do you use to read and write ? Car starts ok and engine has turbo pressure ok or is it in safe mode ? Only problem is mil lamp to flashes or has anyone problem ?
grzanek85
29th March, 2014, 06:31 PM
checksum calc magpro x17 , car start and run ok any problem. Only problem lamp glow plug flashes
antlio
29th March, 2014, 06:54 PM
Can you give me Bosch number of ecu ? Also can you send me the total flash file with chm correct from magpro ?
grzanek85
29th March, 2014, 06:56 PM
0281013010
antlio
29th March, 2014, 07:08 PM
Also can you send me the total flash file with chm correct from magpro ? If i correct the chm with evc can you write it without modify the chm again with magpro ?
grzanek85
29th March, 2014, 09:53 PM
no problem, I send file mondey ok?
mcgywer
5th July, 2014, 09:21 AM
Can anyone make immo off
Polo EDC17U1
Thanks in advanced
Mat
mcgywer
7th July, 2014, 12:27 PM
Any Help with that ecu?
tqnata83
7th July, 2014, 01:22 PM
try this and report
pass in pm
lupu_sandu
7th July, 2014, 01:33 PM
Can anyone make immo off
Polo EDC17U1
Thanks in advanced
Mat
Pass in PM.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.