Chineese Galletto V54

[Ecu Solution Developer]

Galletto programm show me 12,8V

Need galletto external 12V????

My laptop battery is full

I have IBM A31 Laptop

I testing later on BMW X5 2007 EDC16

This is hw problem at 99%
Pls attach hi res photo, probably hex inverter trigger is wrong

[bersch8688]

Ok guys

I have tested!

K-line not work!!!

When i use CAN work Fine!

I post later Photo from my interface

[bersch8688]

here photos from my galletto V54

264688

264689

264690

264691

How to Fix???

[teerak2uk]

here photos from my galletto V54

264688

264689

264690

264691

How to Fix???
what radio is in the car is it the original?

[bersch8688]

VW Passat 2002 Original Navigation Plus with Display

[carmageddon]

here photos from my galletto V54

264688

264689

264690

264691

How to Fix???

pics 3

high quality relais :-)

http://s28.postimg.org/s5acgwcw9/aromat.jpg (http://postimg.org/image/s5acgwcw9/)

[Chippy0815]

@ bersch8688
may you show me how your interface looks from outside?
I'm just wondering because my one looks diffrent and the Galletto "4" i saw till now look all same, but yours look diffrent...hmmm

[Chippy0815]

@ bersch8688
may you show me how your interface looks from outside? (housing)
I'm just wondering because my one looks diffrent and the Galletto "4" i saw till now look all same, but yours look diffrent...hmmm

[Edc17tricore]

here photos from my galletto V54

264688

264689

264690

264691

How to Fix???

You have to change hex inverter trigger.

Photo attached

[bersch8688]

Ok

Where i can buy new hex inverter trigger???

[Edc17tricore]

Ok

Where i can buy new hex inverter trigger???

In any electronics store ;)

[obd.tech]

"probably hex inverter trigger is wrong"..........so is the wrong part fitted.....or is it faulty?
Are the Yellow 'Aromat' (Panasonic Japan) relays fitted to this PCB, much better than the usual China quality? How do they compare with the Omron (Best?) ones?
I also read that apart from 'upgrading' the relays, that some transistors are recommended to be changed? Can someone give more information please. I'm looking forward to receiving my V54, so looking for any tips from you Knowledgeable guy's :beer:

[carmageddon]

"probably hex inverter trigger is wrong"..........so is the wrong part fitted.....or is it faulty?
Are the Yellow 'Aromat' (Panasonic Japan) relays fitted to this PCB, much better than the usual China quality? How do they compare with the Omron (Best?) ones?
I also read that apart from 'upgrading' the relays, that some transistors are recommended to be changed? Can someone give more information please. I'm looking forward to receiving my V54, so looking for any tips from you Knowledgeable guy's :beer:

best relais are this

1 omron
2 siemens
3 axicom

if your tool has not already these component, you need to buy them

1 : OMRON G5V-1 5VDC
2 : OMRON G6AK-234P ST-US 5VDC
2 : 74HCT245 NXP
2 : 74HCT125D NXP
3 : 74HC14D NXP
2 : ST485 or MAX485CSA+
3 : E-L9637D
2 : LM393
1 : HEF4011BT NXP
1 : 16 MHZ QUARTZ

[laylairizarry1987]

So can we use v53 with the new v54 software and call it a day ?

As I know, you can't use V53 with the new V54 software.

[Edc17tricore]

As I know, you can't use V53 with the new V54 software.

Yes, you can update v53 to v54 if you have correct sw update ;)

[Chippy0815]

As I know, you can't use V53 with the new V54 software.

here are some guys that already done this modification, so it must work!

[Chippy0815]

i already have v54, but my device seems to be corrupt and i will send it back.

[moky]

just receive one unit, install perfect tested on vag edc15 R/W ok other tests later..

[Chippy0815]

@moky
where did you buy your unit? And does it have leds on top or at the side?

[bersch8688]

HELLO

MY GALLETTO V54 NOT WORK ON BDM!!!

TESTED ON BMW E70 3.0D EDC16
TESTED ON VW PASSAT 1.9TDI EDC15 NOT WORK

[morgano]

Time to ask for a exchange to your chinese seller, i guess.

[bersch8688]

EDIT!!!

My galletto v54 work K-line.

I have read my vw passat edc15 with mpps.

After read i change the tool to galletto.

Galletto works fine
Ecu id ---> ok
Flash read ---> ok


I dont understand.


Galletto works fine after read ecu with mpps tool


-----------------------------------

Tomorrow i test again in BMW X5 E70 EDC16 BDM

[obd.tech]

Connection fault somewhere?
Vehicle battery voltage causing issues? (use a battery support unit/smart charger)

Just received my V54, How do i know if the software is infected with virus/ok to install? (i read the V53 was a problem)
The cd only has FGTech Galletto Edited v1.0 (134mb), Gall Win7 setup (379k) and the interface driver (1.84mb)
Avast shows 2 suspects? EOBD.exe and fgt2xx.dll =malware-gen
Any help would be good. Keep up the good work guys :beer:

[morgano]

Connection fault somewhere?
Vehicle battery voltage causing issues? (use a battery support unit/smart charger)

Just received my V54, How do i know if the software is infected with virus/ok to install? (i read the V53 was a problem)
The cd only has FGTech Galletto Edited v1.0 (134mb), Gall Win7 setup (379k) and the interface driver (1.84mb)
Avast shows 2 suspects? EOBD.exe and fgt2xx.dll =malware-gen
Any help would be good. Keep up the good work guys :beer:

Don't worry, cd has no virus.

[moky]

@moky
where did you buy your unit? And does it have leds on top or at the side?

2014 Latest Version V54 FGTech Galletto 4 Master BDM-TriCore-OBD Function-OBDAUTO---BMW OPS VAG-COM,Tacho Universal,KWP2000,BMW Scanner,BMW Carsoft,ELM323,Code Reader,Can-bus (http://obdauto.com/views.asp?hw_id=2743)

[Chippy0815]

@moky
thx mate...so your version look exactly like this on the page? (leds on the side?)
This is same like i have too, but my one doesn't work :/

[bersch8688]

BDM not work Galletto 54

chinsese send me this file

265058

[obd.tech]

'chinsese' :smile: instructions mean you have to connect in the small CMD pcb and 12v switched power ?
Then it works for BDM?.......i'm trying to learn :beer:

[heteromies]

'chinsese' :smile: instructions mean you have to connect in the small CMD pcb and 12v switched power ?
Then it works for BDM?.......i'm trying to learn :beer:

BOsch ECU:s need external power supply. Yes, need to use that flat cable. Be sure red marked wire position.

[obd.tech]

BOsch ECU:s need external power supply. Yes, need to use that flat cable. Be sure red marked wire position.
What amp supply is required/best? Is it best to fuse it? rating? If you get the red wiring incorrectly placed, what happens? Any damage to PCM or Galletto :blue:

[gezame]

Hi
If you wiring incorrectly bdm, if ecu is bosch, burned ecu micro.
Br.

[obd.tech]

Install sw to default place c:\fgtech

Connect galletto v54 to usb port.

Go to device manager and unistall actual driver of fgtech.

Unplug fgtech from usb and plug it again.

Install drivers provided into c:\fgtech folder. This is important, older drivers won't work,

Then make usbfix with same file FG as used with v53.

Then try to open sw, if OS is xp run eobd.exe not eobd2.exe

If OS is win7 run eobd2s.exe.

Regards,
Sorry Guys but i need help!
Is there a totally idiot proof install guide to this V54??
my xp pro sp3.....i installed the program.......try to start it(nothing happened)........install again.......plug in usb.......auto search for driver from cd......ok.......try to run prog again.......and get this screen
second install had some files missing like in the second photo?
Help.....my head hurts :grey:

p.s. why is there no instruction on the CD?

[Chippy0815]

i tried it that way....and this is the common way...but in my case didn't work, so i think my tool is corrupt:

have a try:

https://www.youtube.com/watch?v=fannX7MMths

[yellowstilo]

Sorry Guys but i need help!
Is there a totally idiot proof install guide to this V54??
my xp pro sp3.....i installed the program.......try to start it(nothing happened)........install again.......plug in usb.......auto search for driver from cd......ok.......try to run prog again.......and get this screen
second install had some files missing like in the second photo?
Help.....my head hurts :grey:

p.s. why is there no instruction on the CD?

For Windows XP you must open EOBD.exe, not EOBD2.exe....
In your case i would recommend to remove all installation files and reinstall the software (install first time, install drivers, open shortcut (with Dragan xxx message), reinstall software again, open with EOBD shortcut.

[Edc17tricore]

Is possible to update old v53 clone and run it in windows xp, win 7 and 8.1

A little video test of first unboxing a chinese v53 and run it with v54 updated sw


https://www.youtube.com/watch?v=9JS7AM_HNis

[heteromies]

Maybe oft. I'll have version 0384. Is that also chinese? Buyed about year ago. Seller says its EU clone. Is there what tool versions for sure EU clones?

[garagetech]

As ecu solution mentioned you will have to write the eeprom file to a different version , you will fine all necessary files here on dk good luck

[Edc17tricore]

As ecu solution mentioned you will have to write the eeprom file to a different version , you will fine all necessary files here on dk good luck

Write ept file from other version is useless.
In ftdi is written only vin e pid code, not other ;)

[moky]

just tested mine on bdm and i have 16V out for 12v on power suply...someone know which component in cause?


thx !

[obd.tech]

i tried it that way....and this is the common way...but in my case didn't work, so i think my tool is corrupt:
have a try:

https://www.youtube.com/watch?v=fannX7MMths
Chippy buddy, i think you made the same mistake as me?
if you look at this utube (clearer picture)
http://www.youtube.com/watch?v=R0gpO0wAxZw
and follow it spot on.......after you install first.....then plug in the usb.......you have to install the v54 driver.......i made the mistake of pointing the software to the cd's 'driver' file.......look at the utube......you point the software to look in the installed C:Fgtech\'fgtech_new_driver' ( that you've just loaded to C).......Then load setup the 2nd time and let it open the software on completion......'DADA'.....it works!!:joyous: Yippee.....easy when you know how.......but so easy to miss a vital simple mistake.
End up doing your head right in.....and others just say....'na...works fine for me'

If this helps anyone......hit the 'Thanks' button :top:

[mislav88]

just tested mine on bdm and i have 16V out for 12v on power suply...someone know which component in cause?


thx !

power adapter?

[Chippy0815]

@obd.tech
thx mate, but i did it exactly like this for about 4 times and some guy from forum helped me too, but doesn't work. My device seems to be corrupt!

[moky]

power adapter?




power adapter ok...

thx

[damianowariat]

Hello colleagues, I have installed V54 and fires on galletto 3, the program starts in August but you can not do anything ... nothing ever will, operation and does not display Tool-August 0475 as on the V53 .... please help

[sogaro]

Its obviuos that most guys here have there FGtech running one way or the other, please i need help in reading a MED17.5.6
http://www.digital-kaos.co.uk/forums/f152/fgtech-v54-help-needed-426180/

[damianowariat]

bubu colleague says that they can, use the V54 for Galetto 3 but as it is not ok please help in updating :

[ttzag]

Hi
Some one know how to read this ecu ?
Power up and boot point ?
Ssangyong actyon
AM29F400BB-55EE0
Infenion c167
Thanx

[robytza]

desolder 29f400 and read it with programmer

[ttzag]

I don't have adapter for it

[robytza]

this is not the 29f400bb
its the one from the first picture (at the bottom)

[ttzag]

Its AM29F400BB
55EE0

[carmageddon]

is 29f400 tsop 48

[robytza]

oh...i see ... buy an adapter for it

[ttzag]

Thank you ..u realy help me

[robytza]

sorry. i dont have any other good idea or information to help you... i think is the easyest way to solve your problem

[dimitar]

Its AM29F400BB
55EE0

use piasini,mpps or galletto c167 generic mode to read the flash.

Bootstrap pin mcu is P0L.4 short to gnd with 100ohm resistor before apply power supply then read thru k-line

[ttzag]

thank u dimitar .. this what am searching for , but i need scheme for power up and k-line ,, i dont have the car only ecu .
i have galletto.

[Libang]

my V54 hw .... wtf is 2x blue ? is unused and you see that there's something burned? Today I received the package, I have not even tried 267032

[wiski]

Poor quality overheated relay

Sent from my GT-I9100

[afentikoulis]

I read original file from SEAT IBIZA 1.4 16v
Marelli IAW4mv
After that i don't get ecu ID again
I get ID only when i disconect car battery for 10min
I try to write the ecu but the connection last again.
Any ideas?

[bersch8688]

My galletto dont work on bdm
Today tested again on Mercedes Delphi DCM3

"Micro not supported"

Error message

Please send log file to xxxx@galletto.it

[Chippy0815]

today my new galletto v54 arrived. The Mainboard looks little diffrent, but the most important thing is, this time it works!!

[sogaro]

today my new galletto v54 arrived. The Mainboard looks little diffrent, but the most important thing is, this time it works!!

Worked BDM or/ and Tricore?


Sent from my iPhone using Tapatalk

[Chippy0815]

Worked BDM or/ and Tricore?


just got it today...no bdm tested, no tricore tested...and i think this can take a while.....sorry mate.

[automocion]

Worked BDM or/ and Tricore?


Sent from my iPhone using Tapatalk

Yes I tested mine from obnauto on bdm edc16 dde7 bmw e90 and worked ok.


Enviado desde mi iPhone con Tapatalk

[milanocito]

how much time need galletto v54 to write file

on me 7.1 1h so much

is that normal ?

[wiski]

No. 3-4min is normal

Sent from my GT-I9100

[milanocito]

why mine take 1 h ?

maybe because the pc ?

[crackerx]

hello

i want to remap my 320d year 2004 euro 4 with fgtech galleto clone v50
i have succesfully read the ecu map, the ecu is ecd16c31


is a risk to write the map with this tool?
i don`t want to damage the ecu because i don`t have a BDM dump backup and BDM tool wright now

many thanks

[betrescudan]

no risks...go on my friend

[morgano]

Fgtech V50 has BDM ;)

[milanocito]

anyone know how much time galletto v54 need to write file ?

[hollow]

bought galletto v54 a few months ago ,spent a week or so getting it to work perfectly on windows7 32bit. made a backup of folder just incase . haven't used pc for a few weeks ,come to use it and it doesn't work now get an error about an update click ok ,get a crash report error .

does anyone have the full install for v54 without the lpk.dll virus attached to it . or is anyone doing upgrades to them/ selling correct working software . I also have diagbox on same pc 1.86ghz dual core intel with 2 gb ram installed . don't mind paying if it corrects the problem .

[2200]

ME7.1 is normal 1h it is old me7
you can find in 2.7 bi/turbo audi

[Chippy0815]

@ hollow...
I'm using this one....don't know if this is helpful for you.
I think we are using all the same software

http://www.chinaautodiag.com/download/FG%20TECH%20V54.zip

[hollow]

sounds crazy but I just downloaded this one >https://yadi.sk/d/tT0bDRiDLCu7a same thing I think as an iso . installed it run it .re installed it and it worked spot on first time . bloody days ive been messing about ,also has the added benefit of not having the Chinese virus lpk.dll attached to it

thanks for the reply chippy

[gezame]

ME7.1 is normal 1h it is old me7
you can find in 2.7 bi/turbo audi

Hi friend
This old me/.1, esemple 2.7biturbo, read about 4m, write 25m with old galletto 1250.
Br.

[2200]

Hi friend
This old me/.1, esemple 2.7biturbo, read about 4m, write 25m with old galletto 1250.
Br.

no one talked about 1250

[volkswagen1234]

Hi all. I have a problem with my Fg-Tech 4 V54, or have someone fix eeprom? to ftdi? thanks

[gezame]

no one talked about 1250

Hi
I know, it was just a comment.....

[moky]

Hi,

i have a probleme with mine look picture please

http://img15.hostingpics.net/thumbs/mini_828372pbv54.jpg (http://www.hostingpics.net/viewer.php?id=828372pbv54.jpg)

do you know wich component could be in cause? power adapter 12V ok

Thanks!

[morgano]

@moky

does it show 16V also when plug to obd on car?

[moky]

no, on car 12v ok only with power suply

[gezame]

Hi
Sure you power suply is ok?

[morgano]

I bet power supply gives more volt than the announced 12V, specially if it is not switched and stabilised. If it is normal power supply with just the transformator coil, diodes to rectify, resistor and capacitor you can find that it can give 15 or 16 volt easily that should drop when you put load on it and draws good current.

[moky]

i tested with 3 power suply,same problem and i have lot of hardware on this power supply..problem is in v54

i will test thanks morgano

[Babos]

Hi,

i have a probleme with mine look picture please

http://img15.hostingpics.net/thumbs/mini_828372pbv54.jpg (http://www.hostingpics.net/viewer.php?id=828372pbv54.jpg)

do you know wich component could be in cause? power adapter 12V ok

Thanks!

I dont know, but i think he give 16V because you select JTAG/BDM some JTAG need 15V for programing!(info from piasini)

[moky]

same problem with tricore....

[Chippy0815]

to check if you power supply is ok or not you can check easily with a voltmeter (while it is NOT connected to the fgtech)

[moky]

Power supply is 120% ok !!!

[bersch8688]

Tested my FGTech Galletto V54

Golf Plus 2006 2.0TDI ---> OBD CAN WORK - Read & Write
BMW X5 2007 3.0TDI ---> OBD CAN WORK - Read & Write

-----------------------------------------
K-Line dont work ---> For K-Line i use MPPS V13
-----------------------------------------
BDM not work but my Probe are not ok ---> i Order new from EVC (EVC probe without any adapter, work 100% on Galletto V54)

[gezame]

same problem with tricore....

Hi
I know any fgtech clone works in bdm and tricore without plug 12v to interface, feeding only througth tricore cable.

[Tachodiag]

BDM 12v on Bosch ecus is mandatory

[amir_82013]

Hi
anyone tested read & write on the RENESAS Renault S3000 with FG54 ?
i can read BDM/JTAG but can't write Boot mode.
i tested with two PC with OS XP

[amir_82013]

Please see this two picture... see Green wire ...
which picture correct ?

[datapage]

Piasini= ok works well - fgtech OBD2 car runs=ok R/W, off the panel instrument - OBD2 does not work bench.

[gezame]

Hi
You do not can write this ecu in obd-bench, only read.
Ecu need see the Key.
Br.

[PartyTwist]

Hello,

I'm a happy user of this hardware but I have encountered my first problem when trying to read Opel EDC16C9. It says it cannot do it over OBD and that I should read it via BDM (Ecu data works). So now I'm wondering if the problem is in my hardware (worked on a variatey of other ECUs without problems) or is this specific ECU/wiring bonkers? The car was probably totalled and repaired quite some times now, so I'm leaning on that option...

Anyone tried this ECU?

Thanks

[javyb]

Hello,

I'm a happy user of this hardware but I have encountered my first problem when trying to read Opel EDC16C9. It says it cannot do it over OBD and that I should read it via BDM (Ecu data works). So now I'm wondering if the problem is in my hardware (worked on a variatey of other ECUs without problems) or is this specific ECU/wiring bonkers? The car was probably totalled and repaired quite some times now, so I'm leaning on that option...

Anyone tried this ECU?

Thanks
EDC16C9 can only write by obd. For read u have to bdm

[soundnavigator]

I have a problem. I install old FGTech 2 v.50-103 on other laptop with Windows 7 64 bit and work ... software start, schreen looks good, have voltage 13.00 volts. But in euro clone v.54 ( from car-prog ) I have a problem. I use START FGTECH.bat file to start software and data change to 01.01.2013 and software start but no voltage and I have " LOW VOLTAGE " indicator, adapter connected. Can you help me to solve this problem ?

271379

[bersch8688]

vagcom, obd2, autoshop, auto theft, immobilizer, locksmith, autohotkeys, digi prog (http://www.ecutool.com) ---> sell Fgtech V54 ---> crap dont work!!!

I order second

Car OBD2 Tools global supplier --- one-stop shopping for your car (http://www.obd2express.co.uk) ---> sell Fgtech V54 ---> work fine K-line and BDM (BDM tested Delphi CRD.11 Mercedes W204 220CDI)

[morgano]

I have a problem. I install old FGTech 2 v.50-103 on other laptop with Windows 7 64 bit and work ... software start, schreen looks good, have voltage 13.00 volts. But in euro clone v.54 ( from car-prog ) I have a problem. I use START FGTECH.bat file to start software and data change to 01.01.2013 and software start but no voltage and I have " LOW VOLTAGE " indicator, adapter connected. Can you help me to solve this problem ?

271379

Your unit is not detected by sw, bad driver i guess. You need install V54 driver, with same as for V50 does not work.

[Chippy0815]

@bersch8688
haha for me mixed thing :D
first fgtech i ordered was totally crap (the one you are now happy with), and the second one (looks similar to the one from ecutool) works really nice :)

[Tecno]

There are two versions of Galletto v54 available from obd2express.co.uk which one did you bought that works fine? There is a -G and a -BG or something like that...

I have one of them, works fine in OBD with Can, never tested with k-line or bdm thou, so not sure if mine is the good one or not...

My version came in a white box, and doesnt have power adapter for bench work... the other version comes in a brown box and has power adapter for bench work.

Which one is the version that works fine with k-line and bdm?

[Chippy0815]

i know two diffrent versions...
from the outside you can see led's are mixed.

1. Version: On AC you have green LED
2. Version: On AC you have red LED

which version you have?

Edit: if you want i can upload both pcb's

[bersch8688]

Ecutool.com ---> Galletto V54
Shoplink: 2014 Latest Version V54 FGTech Galletto 4 Master BDM-TriCore-OBD Function (http://ecutool.com/2014-Latest-Version-V54-FGTech-Galletto-4-Master-BDM-TriCore-OBD-Function_11400.html)
Picture inside PCB
272217

Result:
- K-Line dont work (tested on VW Passat 2002 1.9TDI EDC15P)
- Can work (Tested on BMW X5 E70 2007 3.0D / VW Golf Plus 2006 2.0TDI)
- BDM dont work (tested Delphi CRD.11)
- Tricore not tested


---------------------------------------------------------------------------------------------------------------------------------------


Obd2express.co.uk ---> Galletto V54
Shoplink: 2014 Latest V54 FGTech Galletto 4 Master BDM-OBD Function (http://www.obd2express.co.uk/wholesale/fgtech-galletto-4-master-bdm-tricore-obd-function.html)

Picture inside PCB
272220

Result:
- K-Line Work (tested on VW Passat 2002 1.9TDI EDC15P)
- Can not tested
- BDM Work (tested Delphi CRD.11)
- Tricore not tested

[Chippy0815]

@bersch
first device i ordered looks similar to the one you ordered from obd2express and this one doesn't work at all, so totally crap.

second device i ordered looks diffrent to the one from ecutool, so mybe there are more than 3 devices out there.
But have a look. This one is working nice (pcb looks al little bit crappy, but it works nice)272223

[PartyTwist]

I have one that looks similar/same to the one you bought at ecutool (didn buy it there tho). And I have tested it on various CAN looks like it works ok. Also used it to read VW EDC16U34 and Renault Delphi ~2007 over k-line if I'm not mistaken (and the files look OK). I also noticed that yours, as well as mine were hand soldered/corrected. So the problem could be in the joints somewhere?

[Chippy0815]

@bersch
sorry i looked at your pcb again...it is diffrent to my first one. sorry for that!
But your pcb looks extrem strange, your pcb is wider than standard pcb?!? So it won't fit standard housings?
It looks strange!!

This was my first one (which doesn't work at all) 272239

[betrescudan]

@bersch
first device i ordered looks similar to the one you ordered from obd2express and this one doesn't work at all, so totally crap.

second device i ordered looks diffrent to the one from ecutool, so mybe there are more than 3 devices out there.
But have a look. This one is working nice (pcb looks al little bit crappy, but it works nice)272223
from where did you buyed the good tool?

[bersch8688]

Chinese Galletto V54 support tricore???

[teerak2uk]

Chinese Galletto V54 support tricore???
Yes I did an Audi A4 2.0 tdi 2008 yesterday dpf delete, eco/power map which had edc17cp14 inside

[cool2503]

Same ecu i doit on obd

[Chippy0815]

i ordered this one from eobtwo

[Tecno]

From what I can see, there are currently 3 different Chinese PCB versions of Galletto v54 !

- There is one, where there are 2 leds on the top of the galletto and there are two, where the leds are on both sides, where the connectors are located (power/bdm/obd)

OBD2EXPRESS.CO.UK, sells two different versions of Galletto v54, from different manufacturers:
(note: on the site, the pictures for both items are the same, but the galletto version differs in the leds and package, please check below for correct details)

- Item No. SE61-GB is the one, that has red led next to the power connector, and a green and yellow leds, on the other side, and comes without power adapter and comes in a white box.

New V54 FGTech Galletto 4 Master BDM-TriCore-OBD Function (http://www.obd2express.co.uk/wholesale/fgtech-galletto-4-master-new-bdm-tricore-obd-function.html)

This is the version I have, and I have successfully tested it in several cars over CAN, but I have still to try K-Line, BDM and Tricore Boot... -> Has anyone this version and tested it over K-Line/BDM/Tricore Boot ?

- Item No. SE61-G is the other version they sell, it comes in a brown box, has a power adapter for bench work, and has a green led, next to the power connector, and a red and yellow leds on the other side. This version is a little more expensive... Just a couple of euros... Maybe it's because it has the power adapter also...

2014 Latest V54 FGTech Galletto 4 Master BDM-OBD Function (http://www.obd2express.co.uk/wholesale/fgtech-galletto-4-master-bdm-tricore-obd-function.html)

Has anyone tested this last one ? Does it work over CAN,K-LINE,BDM and Tricore Boot ?

What are your experiences? Please, when you reply, tell us what item n? do you have: SE61 -G or -GB, even if it's from another seller...

Thanks !

P.S.: The version with the two leds on top, appears in the site of ECUTOOL vagcom, obd2, autoshop, auto theft, immobilizer, locksmith, autohotkeys, digi prog (http://ecutool.com) it is more expensive, apparently also doesn't have the power adapter, but the pcb pictures there, don't correspond to the this version of this tool, I don't know why... They mixed pictures from different v54 tools...

If someone has experience with this tool with the two leds on top, on the side where the lettering "Galletto ..." is, let us know if it works !

[Tecno]

i know two diffrent versions...
from the outside you can see led's are mixed.

1. Version: On AC you have green LED
2. Version: On AC you have red LED

which version you have?

Edit: if you want i can upload both pcb's

I have version with red led on AC and green and yellow, on the other side, next to the other conectors.

[Tecno]

@bersch
first device i ordered looks similar to the one you ordered from obd2express and this one doesn't work at all, so totally crap.

second device i ordered looks diffrent to the one from ecutool, so mybe there are more than 3 devices out there.
But have a look. This one is working nice (pcb looks al little bit crappy, but it works nice)272223

I think this is the one I have ! With red lead on AC connector, and green and yellow, on the other side ! It works fine in CAN.

Have you tested it with:
- K-LINE ?
- BDM ?
- Tricore Boot ?

Can you please report ?

Thanks

[jeffbih]

Hi, I have SE61-G tool
I have done immo off on alfa with ecu ME 7.3.1
R/W ok

BR

[javyb]

O have the one with red LED next to power jack. I gave tested on k line works fine, CAN works fine, tricore works fine. Not tested on bdm yet

[Tecno]

O have the one with red LED next to power jack. I gave tested on k line works fine, CAN works fine, tricore works fine. Not tested on bdm yet

Can you confirm if this is the same as the Item No. SE61-GB I described in my above post? Does it have yellow and green leds also, on the other side, nex to the connectors? Did it came in a white cardboard box, with no power adapter ?

If so, on what cars/ecus have you tested it ?

Thanks !

[javyb]

There is green yellow led next to connector but I purchased mine from aliexpress

[Tecno]

There is green yellow led next to connector but I purchased mine from aliexpress

What cars/ecus have you tested it with? For K-line and Tricore boot especially ?

Thanks

[javyb]

Tricore 2010 audi a6.
K line. 2005 Skoda octavia vrs.

[2xded]

Would be nice to see a link to a page describing "purchased mine from aliexpress" :)

[70max]

Hello friends,


I received my FG V54,
do you think this tool
according've mounted components
is a good tool?
The SW version is 0386


I still have not tried
in the car.


Thank you for your answers.


Best Regards Max

[Chippy0815]

oh man....this galletto clone sucks.

It worked really nice and now it won'T start any more. First i got the Message "fgt2xx.dll is missing" and i must reinstall the software.
Ok so i reinstalled the software and now i get the following message:
"ESEGUIRE RENEWAL CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- MAKE RENEWAL WITH FGTech_DOWNLOAD_UPDATE FOR TOOL RE-ESTABLISHMENT"

Any idea how to solve this problem?

@70max
this was my first clone. This one wasn'T working at all (couldn't start even the software....but i think yours work because you got the tool number).

[bersch8688]

Check you date of your PC/Laptop

Set 30.12.2012

[Chippy0815]

@bersch8688
i have v54 not v53, there is no need to change date

[bersch8688]

On windows 7 you need change date!!!

My V54 change date on windows 7

[Chippy0815]

i'm using xp, never need to change date

[70max]

Thank you for your response chippy I have to try the ECU to see if it works

[Chippy0815]

anyone have solution to my post #377?

@70max
but your software starts or not? If so Tool will work

[moky]

hi,

someone arrive to work in jtag renesas with chinese V54 ?

thanks

[Dobermann]

oh man....this galletto clone sucks.

It worked really nice and now it won'T start any more. First i got the Message "fgt2xx.dll is missing" and i must reinstall the software.
Ok so i reinstalled the software and now i get the following message:
"ESEGUIRE RENEWAL CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- MAKE RENEWAL WITH FGTech_DOWNLOAD_UPDATE FOR TOOL RE-ESTABLISHMENT"

Any idea how to solve this problem?

@70max
this was my first clone. This one wasn'T working at all (couldn't start even the software....but i think yours work because you got the tool number).

same error happens sometimes with with eu v54 !! install the v54 software a second time !! do not delete the software just install it again !

i use win 7 after the second install v54 start again !!

br dobermann

[Chippy0815]

@dobermann
like i have written.....i already done this.....
first i got the error message "fgt2xx.dll is missing" and that i have to reinstall the software.

So i reinstalled the software (without deinstalling it)

And now i get the second error message "ESEGUIRE RENEWAL CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- MAKE RENEWAL WITH FGTech_DOWNLOAD_UPDATE FOR TOOL RE-ESTABLISHMENT"
so i think there is some error with the license....but how can i modify?!?

Change date = not solved
written new fdti = not solved

any other clues?
And thx for your help :)

[austingreen]

Look here. It is posted on another site.
http://yadi.sk/d/tT0bDRiDLCu7a

Nothing found
The owner may have deleted files or made it private.
Or maybe the link contains an error.

Then I search google, and find this: http://www.chinaautodiag.com/download/FG%20TECH%20V54.zip

[austingreen]

Hi

I have order on ecutool.com my fgtech galletto V54
Today i receive my package

I tested on my VW Passat 2002 1.9TDI ---> EDC15 ---> Dont read


I click ECU ID
Read 100% after 5 seconds close the programm complet

Again start programm click ECU ID
ERROR
please send log file to fgtechgalletto@xxx


Fgtech galletto dont read k-line edc15?????

Maybe the main reason is you didn't connect external power supply when tested on VW Passat 2002 1.9TDI ---> EDC15, it needs use that flat cable. Be sure red marked wire position. But BMW X5 2007 EDC16 read ECU via OBD? it needs not connect with external power.

[70max]

@70max
but your software starts or not? If so Tool will work


It is my sw starts well,
The relay will operate and feel yellow and red leds are flashing
with external AC power supply.
Should I try to read ECU
when you read in OBD ECU you must put the reduction?
As the sw only in OBD
View image

Thanks for your help

[Tecno]

Does the mini gender changer you have, has all the pins in one side? Or some pins missing?

Be carefull, if you have all pins, you need to cut some!

For all cars, you need to use that adapter. Only for trucks you take it out. If you do not follow this, you might burn galletto, ecu and or obd port...

[Chippy0815]

@Techno
are you sure you need this gender changer for all cars?!?
Why is it needed? I never used it till now.

@70max
when softwares starts and relais inside the the galletto are "clicking" your tool have to work.
You can read some cars, there won't be any problem.

But about the gender changer i don'T have a clue for what using it, sorry.

[70max]

Does the mini gender changer you have, has all the pins in one side? Or some pins missing?

Be carefull, if you have all pins, you need to cut some!

For all cars, you need to use that adapter. Only for trucks you take it out. If you do not follow this, you might burn galletto, ecu and or obd port...

Thanks for your reply,
my "mini gender" has some loose pin
good for all cars?
view photo

[70max]

@Techno
are you sure you need this gender changer for all cars?!?
Why is it needed? I never used it till now.

@70max
when softwares starts and relais inside the the galletto are "clicking" your tool have to work.
You can read some cars, there won't be any problem.

But about the gender changer i don'T have a clue for what using it, sorry.

Thanks for your reply,


I have never used the FGTecno
and I will not do damage.


Ok now I want to try in Grande Punto MJT 1_3 HP75
I put "mini genger" and later OBD cable and connect it to the OBD car
So link is correct?

[Chippy0815]

like i told you i never used the "mini gender" and if i read in other forums they don't use it too.
I think you only have to use, when software tells you to use it.
For the cars i tested till now (kline and can) there is no need to do this.

Maybe for bdm?!? But don't know!

@Dobermann
thx again mate. I reinstalled software a third time and now galletto works again. Seller means this is a common bug in software. So maybe this would be helpful for other people who will get this error message
"ESEGUIRE RENEWAL CON FGTech_DOWNLOAD_UPDATE PER RIATTIVARE IL TOOL --- MAKE RENEWAL WITH FGTech_DOWNLOAD_UPDATE FOR TOOL RE-ESTABLISHMENT"

so just reinstall the software......maybe twice times and it will work again.

[javyb]

Can anyone advice what pins are supposed to not be connected with the mini gender changer

Cheers

[Tecno]

The picture is correct. That adapter is good one! Use it always

[morgano]

Cut pins in mini-gender changer are 3,8,9 and 11.

[Chippy0815]

That adapter is good one! Use it always
and why is it needed??

[morgano]

To prevent unwanted current to flow in some operation modes. Software instruct you when is it needed and when not needed.

[Chippy0815]

Software instruct you when is it needed and when not needed.
This is my meaning too, because Tecno said to use it all the time....and i don't understand why.

[70max]

The picture is correct. That adapter is good one! Use it always

Hi friend,


Can you explain to me, all the connections of the adapters?


Look at that picture I posted.
Thank you very much.

[Tecno]

This is my meaning too, because Tecno said to use it all the time....and i don't understand why.

Have you read fgalletto's manual?

I said it is needed for cars essentially. If you dont need trucks, you can basically use it always when doing cars by obd, without problems, just to be sure!

All cars i've tried, software always says to put it on.

[70max]

Ok now I want to try in Grande Punto MJT 1_3 HP75


Today GP read 1_3 MJT 75 hp


Twenty-six seconds to read.
File 2 MB


Write not know
Maybe rewrite the car next week.


Best Regards Max

[Chippy0815]

@Tecno
don'T know which kind of manual you are using! In my manual there is nothing writte nabout it. And i never used the "gender changer" for my cars, and software don'T tell me to use it with cars.....
don'T know from which tool you are talking about?!?

here is manual from galletto
http://www.fgtechnology.it/FGTech_EOBD2_User_Manual.pdf

[javyb]

@Tecno
don'T know which kind of manual you are using! In my manual there is nothing writte nabout it. And i never used the "gender changer" for my cars, and software don'T tell me to use it with cars.....
don'T know from which tool you are talking about?!?

here is manual from galletto
http://www.fgtechnology.it/FGTech_EOBD2_User_Manual.pdf
Download manual from here
http://www.fgtechnology.it/

And read page 42 it tells u about the standard adaoter which is gender changer

[Chippy0815]

@jvyb
it is same link that i have postet...but now i saw this page...but can't understand because it is in italglish :D
So does someone know what are "Renesas processors"?

Maybe some italien guy may help.

And again about the pins. Why is it needed to cut? So far as i know all v53 came with cut pins and newer ones (v54) came with uncut pins?

[bersch8688]

BMW X6 3.0D 2008 ---> EDC16 OBD read and write WORK

[Chippy0815]

@bersch8688
do you use gender changer while reading or writing?

[digi men]

I use gender changer by read and write cars ,te softwer tell you when you need to use it, whats here hard to understand, when you chose the driver you will see if you need to use or not !

[Chippy0815]

@digi men
yes because i get irritated of Tecno's words! He said use it all the time.
All the cars i read till now, i never get a prompt to use the gender changer.

One said use it all times, one only when you get a prompt.
I think this will confuse the people totally.

I thought also it is correct to wait if you get the prompt to use it, than use it otherwise leave it!

[sepistar]

mini gender you must use when read-write ecus with tricore processor on bench.
br.

[sepistar]

the other day,it failed to write an edc16c35 from bmw.
then i have to recovery through bdm.
br.

[morgano]

Guys, nothing difficult here.

V53 and v54 sw has a picture of the gender changer just below the serial number "Tool-xxxx"

Just select the driver you are going to use and see the little picture, it can show "standard use it" or dashed pucture "no use it" easy as that. Follow on screen directives, don't go on autopilot or you may find a surprise and smoke getting out your fgtech.

[javyb]

mini gender you must use when read-write ecus with tricore processor on bench.
br.
Wrong gender changer is used when doing cats obd. It is not used In tricore, BDM, or JTag

[Chippy0815]

and last about "gender changer"
May somebody explain why it is needed to cut the 4 pins?

I think nearly all V54 comes with full pin "gender changer" only in v53 4 pins "are missing".

[sepistar]

Wrong gender changer is used when doing cats obd. It is not used In tricore, BDM, or JTag

without the mini gender i can't read edc17 tricore,think you have messed up mini gender with that big black adapter.
br.

[javyb]

without the mini gender i can't read edc17 tricore,think you have messed up mini gender with that big black adapter.
br.
Whet big black adaoter is that then? Read the manual. Mine reads edc17 tricore without gender changer

[Chippy0815]

manual don't say it clearly about tricore, only about jtag NOT to use the gender changer

[70max]

Hi friends,


V54 reads and writes c3 1_4 hp68
edc 16C34?
by OBD in the car
Does anyone know?


There is special procedure to do?


Thank you for your answer

[teerak2uk]

Hi friends,


V54 reads and writes c3 1_4 hp68
edc 16C34?
by OBD in the car
Does anyone know?


There is special procedure to do?


Thank you for your answer
Should do just try it

[70max]

Should do just try it

But if reads must also write
without problems?

[teerak2uk]

Be like everyone else and try because going by this thread some v54 do tricore and some dont so gamble still stand cos if a member says his will read/write the c3 dont mean yours will

[70max]

Be like everyone else and try because going by this thread some v54 do tricore and some dont so gamble still stand cos if a member says his will read/write the c3 dont mean yours will

Ok I feel tomorrow,
We hope all is well


Thank you for your help.

[Tecno]

@digi men
yes because i get irritated of Tecno's words! He said use it all the time.
All the cars i read till now, i never get a prompt to use the gender changer.

One said use it all times, one only when you get a prompt.
I think this will confuse the people totally.

I thought also it is correct to wait if you get the prompt to use it, than use it otherwise leave it!

Do you know how to read english? First you say this is not in the manual, then someone corrects you, then you come again...

The manual is clear! Use the adapter, always when reading/writing by obd! They even warn you against the dangers of not using it when its needed.

V54 and all versions from 2012 on, use it!

[Tecno]

The only times when it shouldnt be used, is when your working on trucks or with bdm/jtag, etc...

It is true that the software tells you when you should use it or not, but the manual is clear and for all cars i did, with version v54 the software always says to use it!

There are some clones where the adapter is wrong, and has all the pins, so you need to find a picture of a good one, and remove the ones that should be missing.

No harm comes from using the adapter all times, when you use by obd on cars (like the manual says you should!) but if you end up not using it on one of the times you should, then you might end up with burnt galletto if not a worst result!

[Chippy0815]

@Tecno
what is wrong with you? :D
Now 2 People tell you that gender changer only have to use when software tells you!!

So please stop confusing other people! USE GENDER CHANGER ONLY WHEN SOFTWARE TELL YOU!!!

[morgano]

Well, to be honest he have said that for all the cars he made software said to use it

[Chippy0815]

@margano
no he said that the soft tells him all the time to use it!

And that's not correct. The cars i make the software always tell me NOT to use it.

And he said clear, that it is better to use the gender, because manual says it too.

But my meaning is diffrent.....
i have same meaning like you.

JUST USE IT, WHEN SOFTWARE TELLS YOU!

[70max]

Ok I feel tomorrow,
We hope all is well


Thank you for your help.

Hi friends,


Read and written
Citroen C3 Bosch EDC 16C34


all good
5 minutes total to write.


Read and written
BMW 525 (E39)
Everything Good.


Best regards

[Tecno]

@Tecno
what is wrong with you? :D
Now 2 People tell you that gender changer only have to use when software tells you!!

So please stop confusing other people! USE GENDER CHANGER ONLY WHEN SOFTWARE TELL YOU!!!
I know you have trouble understanding what I say, so let me put it here, so every one can see for themselfs and judge who is right:

http://tapatalk.imageshack.com/v2/14/08/17/0b4754c39e168610d2a08636e2ef5fdf.jpg

I will not discuss this matter any long.

[Chippy0815]

@Tecno
yes there is nothing to discuss....

YOU will use the gender changer all the time.

And the rest will use it only when software tells to use....discussion finish :)

[alcorte]

I think that new galletto 4 is same galletto tunertool, but galletto chinisse with one software best.

[Chippy0815]

Hi some uestions
1: in fgtech you got two ways to read out via obd "Flash" and "Eprom" when i read out with "Flash" is this a full read, like read from bdm and contains this the eprom too?
2: If i just read out the Eprom, this will contain only the maps needed for "chipping"?

3: has someone ever tried mini R50 with fgtech? Read and write ok?

[carmageddon]

via obd you can read only flash and MPC for some ecu, not e2p!

the readout for edc17 or med17 and most of ecu is always partial, not full!

for mini no problem with all ecu (without Tprot), by obd work good (if tool have big quality)

[Chippy0815]

@carmageddon
thx for reply. I'm just wondering because my readed file was 512KB (like fgtech show in soft, too) but nearly all the files i found for the mini r50 are 64kb in size?
And the old one isn't edc17, i don'T exactly know which edc it is. It only tell me "kline"

[carmageddon]

diesel or petrol?

anyway, on the old ecu for diesel (bosch edc) and petrol (siemens) the file are 512 kb for full flash and 64 for partial flash

[Chippy0815]

It's petrol 90hp, so it is full flash ok.
Is there a way to read partial too?
Or is it better to read and write full?

My sugestion was....if the filesize is small, the writing process will be faster and less issues (shorter flashing time)....or am I'm wrong?

[carmageddon]

for this engine is simple to have 115-120 hp only with unlock throttle and complete mod!
the file size exact for full flash is 512 kb, its better to read and write complete flash...the process is quick...no problem

[Chippy0815]

@carmageddon
ok thanks. Don't know what your meaning about quick is :D
Reading was about 18 Minutes.

[carmageddon]

yes but if you think that one edc16c39 fiat-alfa-lancia need around 50 min is quick :-)

[Chippy0815]

huh ok....if my computer would transfer in that speed (512kb in 18min) i already had thrown it out of my window :D
Hope this is not that off topic here.
Did you already tune an Mini One 1.6l? Is the clue really only to change maps of throttle? I mean just to have same power like the cooper or is there even more to do?
I never done these cars.

[carmageddon]

90 hp and 115 hp have same engine, but 90 hp have throttle only to 50%, i do many of this

[carmageddon]

the engine managment start from hex 73000, from here you can see the difference between files

274141

[70max]

the engine managment start from hex 73000, from here you can see the difference between files

274141

Hi carmageddon


please pass for zip.
Thank you so much

[Chippy0815]

@carmageddon
yes i know that both have same engine and that one is castrated cooper :D and i know that the throttle map of the One are less than the one of the cooper, but is this the only clue?
I know till 3000rpm it is nearly same and than the one of the cooper got more "power"

But i still can't believe this is the only clue? Only throttle? No changes on ignition? Thanks for the file, i will have a look later time :) maybe i will find my answer there :)

[carmageddon]

read post #437

i wrote : and complete mod

anyway, you need only to export 115 hp logic for have the same power...obviously, only complete mod (logic+mod) can give correct work

[meteor80]

Can somenoe post good resolution photos of galletto v54 which works good with k-line?
I'd like to compare with mine.

[70max]

Can somenoe post good resolution photos of galletto v54 which works good with k-line?
I'd like to compare with mine.

Hi my friend this photo
FGTECH V54
It works well "can-bus" and k-line.


I have to try if it fits in BDM and J-tag


Best Regards Max

[meteor80]

Hello.
Mine looks the same but I cannot read skoda superb EDC15+.
If You can please attach photo in big resolution.
I think that some parts are soldered in bad place or maybe wrong value.

[betrescudan]

the engine managment start from hex 73000, from here you can see the difference between files

274141
please password

[Lexas]

Hello.
Mine looks the same but I cannot read skoda superb EDC15+.
If You can please attach photo in big resolution.
I think that some parts are soldered in bad place or maybe wrong value.
i cant read mine skoda superb to, but i succesfuly read it in vw golf 4 section. i think its software isue.

[digi men]

Today i have read with my v54, an Alfa 159jtdm 150hp edc16c39 2 times witout problems by obd k-line, read time 40 minut !

[wadim21]

Renault megan 3 2010 y.tried SID 305 boot mode not work.via obd only ident,galletto can`t read flash.

[gezame]

Hi
For obd read, you need low water temp.
cold engine.
Br.

[carmageddon]

obd R-W with temp under 50? only on renault-bosch diesel

renault-siemens diesel dont have this strategy

[wadim21]

maybe galletto work obd with Sid 305 only old version ,from 2008 y

[carmageddon]

fg work on sid305, tested!
is not important year, only protocol

[gttuning]

Today i have read with my v54, an Alfa 159jtdm 150hp edc16c39 2 times witout problems by obd k-line, read time 40 minut !
have one in garage better job BDM ecu very handy to take out.

[digi men]

I know that, i have try it, to see if the toll read this ecu without problem and that i know wat work or not ;) , i have made the car with a other toll :joyous:

[wadim21]

fg work on sid305, tested!
is not important year, only protocol
you about clone?

[carmageddon]

you about clone?

tested with clone v53 and original

[wadim21]

my gall V54 in boot mode not work with SID 305. obd read only ECU data

[2200]

have some one make it work on Win8?
FTDI driver?

[gezame]

obd R-W with temp under 50? only on renault-bosch diesel

renault-siemens diesel dont have this strategy

Hi
Friend, I once had a problem with one sid305 (interface cmdtec), and can only read-write with cold engine.

[carmageddon]

i did not temperature problem on siemens, only bosch, i use kess and fg

[bersch8688]

Mercedes V Class 2003 220CDI EDC15C5 ---> K-line read and Write WORK

[wadim21]

v 54 work with Sid 305 or not?

[wadim21]

i tried today megan 3 sid 305 via obd work good.but ~~ one the table~~ not work via obd. maybe different ECU

[carmageddon]

have you respected procedure for stay on with keycard?

[wadim21]

on the table,ECU without BCM and key

[carmageddon]

ok, but, when you try to read on a car i wanna know

[b2s15]

on car ok for reading, no need to forced contact.
but for writting, i didn't can force the contact, and so, it stopped during writting, it costed me 1000€ for new ecu.

[carmageddon]

the renault with keycard need all to activate procedure for read and write, this is valid for cmd, kess, genius, fgtech...the other tools i dont know

[betrescudan]

i do not understanding well what is the probblem here...is that when you try to make contact,the contact offen ?.....if you press first the bottons open and close the doors,and then press the start botton for 10 secconds without touching clutch or break pedal,and the contact rest on for long time....maybe i understand wrong the subject?

[jojo1212]

if you are buyin chinese stuff, then stay away from this fgtech v54
get kess v2 chineese. works better
well , at least most of the time

[Chippy0815]

if you are buyin chinese stuff, then stay away from this fgtech v54
get kess v2 chineese. works better
well , at least most of the time

chinese fgtech v54 is the better clone, the chinese kess is crap, don't work on kline at all. (new devices since end of 2013)

[amir_82013]

History version FG original :

[stefaudio]

EDC16c9(Opel) OBD CAN-R/W---OK
EDC16c9(Opel) BDM-R/W---OK
EDC15P(VW Bora)K line R/W---OK
EDC16c3(Peugeot 307 1.4HDI)--K line and BDM R/W 100% correct

[stefaudio]

EDC16c3(peugeot)K line---only ecu data---Galletto mini EU version Portugal(my A.....s)
EDC16U1(VW Touran)K line----only ecu data ,no read

[Chippy0815]

what exactly is the difference between the mini and the normal one?
Please don't give me as answer: the size :p

[linu]

mini not support bdm

[Chippy0815]

ah ok so mainly same as kess / ktag

[stefaudio]

Also MINI not support K+Can :):):)

[linu]

not support because defective k + can

[linu]

:beer:




where to buy a good Chinese clone FGTECH V54 ?

[linu]

pics 3

high quality relais :-)

http://s28.postimg.org/s5acgwcw9/aromat.jpg (http://postimg.org/image/s5acgwcw9/)

Aromat relay by Nais (Panasonic)

[70max]

Hello.
Mine looks the same but I cannot read skoda superb EDC15+.
If You can please attach photo in big resolution.
I think that some parts are soldered in bad place or maybe wrong value.


Hello mate,


My friend says that FG V54 with these components
that all works:
jtag
BDM
Boot
OBD


mine has these components, but still I have not tried
I hope to try soon.


Best regards max

[linu]

There are many versions of pcb, but I see that some
have wrong components !! and missing components !!
HCT645 is wrong !! MAX481 is wrong , LM2903 is wrong and missing transistor U2
instead I see capacitor !!
277063
sorry I posted 2 photos
the first is the right

[70max]

There are many versions of pcb, but I see that some
have wrong components !! and missing components !!
HCT645 is wrong !! MAX481 is wrong , LM2903 is wrong and missing transistor U2
instead I see capacitor !!
277063
sorry I posted 2 photos
the first is the right

No components of your are different
and if I'm not mistaken what you have
marked you run the BDM

[linu]

the components of my pictures are wrong !! and can not work ever !!!
FGTECH of photo is not mine, I found the photo a few pages back

[Chippy0815]

did someone try already Z22SE Vectra B?
ID read ok, read file up to 50% than error (every time)

any chance to get this file thrue OBD? Or maybe possible on the table?
Or have i to desolder the chip (very bad with this one :/)

Maybe someone have original File for this vehicle?
No. 12202143 DFZF

thx!

[zanovo]

Hello
Plese help with fix files fo FTDI and eeprom for Chines Galletto V54.
SN: 4439
My device can`t start after some attempts....
Thanks in advance.

[aristeu]

Hello, I have used it and so far it worked well with the ECU on the bench, I do not risk and do not recommend using the OBD2 socket.

It covers lots of light and heavy vehicles.

[meteor80]

Hello.
Does someone tested Galletto v54 with Siemens PPD1.2?
I have different signals from users.
SOme of them tells that it doesn't write.

[wadim21]

hello,someone tested Galletto v54 with DENSO ECU OPEL 1.7?

[teerak2uk]

Hello.
Does someone tested Galletto v54 with Siemens PPD1.2?
I have different signals from users.
SOme of them tells that it doesn't write.
Yes has worked OK for me

[2200]

did someone try already Z22SE Vectra B?
ID read ok, read file up to 50% than error (every time)

any chance to get this file thrue OBD? Or maybe possible on the table?
Or have i to desolder the chip (very bad with this one :/)

Maybe someone have original File for this vehicle?
No. 12202143 DFZF

thx!

my mini has v54 worked on this ecu.
but you can also use mpps v12 on these ecu

[Chippy0815]

@2200
ok thx. And does MPPS full read?

[2200]

@2200
ok thx. And does MPPS full read?

yes full read and think it was 512kb
just put also charger 13V

[linu]

Please, anyone knows the real value of this diode

[obnchip]

what is in the white line?
Lv125a is hct125?
the other Ls14???