need manual programming procedure

[ninja123]

I need to make a key for 2010 ford ranger with all keys lost, owner says it was seperate remote so must be mazda system 8C.

I can get pincode but need the manual procedure to enter code and program keys.

Thanks for any info , ninja

[Carkeysa]

I need to make a key for 2010 ford ranger with all keys lost, owner says it was seperate remote so must be mazda system 8C.

I can get pincode but need the manual procedure to enter code and program keys.

Thanks for any info , ninja

Key Replacement or Addition when the customer has only one or no valid key (code word is required)
1. NOTE: If no specific time interval is given, each step should be performed within 30 seconds of the previous
step.
2. Remove and insert key 1 five times at no more than 1-second intervals.
3. After the final key insertion, verify that the security light flashes. (300 ms ON—300 ms OFF)
4. Wait for 5 minutes until the security light flashes at 1.2-second intervals.
5. Input the code word. For additional information, refer to Code Word Input Procedure in this procedure.
6. After verifying that the security light has switched from flashing to straight illumination, turn the key to the ON
position.
7. After verifying that the security light goes off, turn the key to the LOCK position and remove from the steering
lock.
8. Insert key 2 into the steering lock and turn the key to the ON position.
9. Verify that the security light illuminates for 1—2 seconds.
10. After verifying that the security light goes off, turn the key to the LOCK position and remove from the steering
lock.
11. Insert key 3 into the steering lock and turn the key to the ON position.
12. Verify that the security light illuminates for 1—2 seconds.
13. After verifying that the security light goes off, turn the key to the LOCK position.
14. If there are 4—8 keys (valid and/or new keys), repeat Step 5 with each key.
15. Wait for 30 seconds.
16. After reprogramming, clear DTCs stored in the PCM.
RANGER KEY PROGRAMMING PROCEDURES
IMPORTANT : PLEASE ENSURE ALL PRECAUTIONS
ARE OBSERVED AS INDICATED AT THE FRONT OF
THE OPERATING MANUAL.
IN PARTICULAR : For vehicles fitted with STOP/START technology, the battery leads
must not be shorted together when the battery is disconnected as this can lead to damage to the car and
potential personal injury.
PRECAUTIONS

[ninja123]

Ok but how to input pin code??

[Carkeysa]

Code Word Input Procedure
• A code word is composed of eight digits from 0 – 9. The manufacturer has programmed
it as unique figure into the immobilizer module.
• When you have entered the mode for inputting the code word with an unregistered key
according to the procedure described on the preceding page, wait for 5 minutes until the
security light flashes slowly (flashing frequency changes from 300 ms ON / 300 ms OFF
to 1.2 s ON / 1.2 s OFF).
• Input the code word according to the following procedure as shown in the example for
the code word digits “3” and “1”:
1. Turn ignition switch to the ON position while the security light is OFF and count three
illumination cycles. When the light is OFF after the third illumination, turn the key to
the LOCK position.
2. Wait at least one illumination cycle.
3. Then turn the ignition switch to the ON position (within 30 seconds) while the security
light is OFF and count one illumination cycle. While the light is OFF after the first
illumination, turn the key to the LOCK position.
4. Repeat step (2) for the remaining six digits.
5. When the code word is correctly registered in the PCM, the security light stops
flashing and illuminates. Carry on with the respective programming step.

1007_015
Inputting the code word “3” and “1”

1 Security light 6 On
2 On 7 Lock
3 Off 8 Ignition switch
4 One cycle or more A Code word “3”
5 Within 30 seconds B Code word “1”

NOTE: The number “0” in a code word requires 10 illumination cycles.

[Fallen]

Turn the ignition from off to on when the light is out for the required number of flashes for the first number of the security code, then turn back to off when the light is out.
Repeat for all the remaining numbers.

[Carkeysa]

Hope this helps

[iamfooser]

A very detailed instructions

[robert81]

can any of you guys calculate the word code from serial number? i know 3d can but they are ?24. bit expensive

[Meat-Head]

?24 no messing car runs, shut up and cough up

[Carkeysa]

can any of you guys calculate the word code from serial number? i know 3d can but they are ?24. bit expensive

I can only help with the Lucas Immobiliser/

[szkeptmen]

I can only help with the Lucas Immobiliser/

Hi,
Can you help me with 8 digit code ?
The car is Mazda 626 with Lucas immobox.
Lucas 35AS I*ETS 300 330


LC62 67 5G2
Lucas 34AS 52010563A
S/N : 6944627159

Thanks + Rep in advance !

[guillermemosz]

Serial 694-462-7159
pincode 4555-3333

remember to press the button thank you if it worked

[szkeptmen]

Thanks for your reply.
I will try it afternoon !

[szkeptmen]

Yes, this is a working code. :)
THX

[klaudio]

Hi,
Can you help me with 8 digit code for Mazda MPV?

Serial# 7520219033

Thanks

[darknezz19]

I heard T300 has converter for these.

[klaudio]

This type can only be done manually

[sleepyrz]

U sure says not valid?

Take pictur of box

[klaudio]

U sure says not valid?

Take pictur of box

Here is the picture of immo box.

[sleepyrz]

not a lucas box

cant help sorry