2005 toyota yaris fijtsu 25040

[unitycarrental]

Hello members,
Please help with adding:
Key 1 :7E C0 BA 50 90 00 00 00 00 A9 3E 7E 00 00
Key 2 :7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00
Key 3 :7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00263335263335

Thanks in advance.

[Renovator]

Hi.
Write, test and answer here. Start OK, or not start.
263339

[unitycarrental]

Thanks Renovator.
I will try tomorrow and let you know.
Are all 3 keys data included.

[Renovator]

Thanks Renovator.
... Are all 3 keys data included.
No problem. :smile:
3 keys included. Need to be tested. Total checksum needs to be verified.
I'm waiting for a response from you.

[unitycarrental]

I have written file to chip,resolder and installed.
Security light still flashing and car no start.

[Renovator]

Can read dump from EСU?

I need to check synchronization EСU + IMMO

[key]

263435
Hi, try this.

[Renovator]

Synchronization can try to recover ....
Shorting pins 4 and 13 on the OBD connector, switch on the ignition and leave it on for 45 minutes.
Take precautionary measures against discharge of the car battery.
Usually it helps to resynchronize the ECU - IMMO.
Follow this procedure and report the result.

[key]

Synchronization can try to recover ....
Shorting pins 4 and 13 on the OBD connector, switch on the ignition and leave it on for 45 minutes.
Take precautionary measures against discharge of the car battery.
Usually it helps to resynchronize the ECU - IMMO.
Follow this procedure and report the result.
immobilizer in the ecu, no need synchronization

[unitycarrental]

It is an engine ecu with the immo chip 89661-5C180 futjitsu

[unitycarrental]

Can you also make a immo off or virgin dump.

[gwee]

Synchronization can try to recover ....
Shorting pins 4 and 13 on the OBD connector, switch on the ignition and leave it on for 45 minutes.
Take precautionary measures against discharge of the car battery.
Usually it helps to resynchronize the ECU - IMMO.
Follow this procedure and report the result.

have u done this car before??? lol

keys not written correctly

[unitycarrental]

I have written this dump from KEY.
When I insert the keys the security light goes off,but still no start.

[unitycarrental]

Any help here.

[unitycarrental]

Tyrone,
Can you correct this.

[ngakson2002]

I have written this dump from KEY.
When I insert the keys the security light goes off,but still no start.


Hello Mate

When reading your dump key counter has been set to 10 reason why dump is not recognized by either TMPRO2 or EFfi software as Toyota dump.
However, i have reset the key counter to 01 as is supposed to be.Therefore if the 4C data Posted here are Tiris data,i think the dump attached here with your key 1 & 2 added will start the car

[unitycarrental]

Thanks.
I will be happy if this work.
I have desolder the eeprom 6 times now.

[Renovator]

have u done this car before??? lol

keys not written correctly
I repaired the cars of this brand. But the year was more senior. And focus on bridge rescued me always.
By not properly recorded keys.
I agree it can not properly compiled record. But then it is a mistake on the part of the code indicated keys.
I using KMRW in my work. KMRW indicated IMMO data from keys data. I see immo data in KMRW and write in dump.
It always worked. But in my case - KMRW read keys himself, and here they were listed in the read form.

[unitycarrental]

So do you think the last above dump will start car?

[Renovator]

So do you think the last above dump will start car?
I will answer extensive. And you add your own keys. Hands, right in the Hex editor. Provided that you have equipment that allows to check the information in the key ... and dump of immobilizer is not damaged. Below I attach images. In images understood without words. I wish successful experiments. :banghead:
263661

Instead of an epilogue ...
I looked up all the dumps. I have a suspicion that your memory reader read in byte-swap (Dump read byte-swapping). From above was a remark about the impossibility of identifying dump special equipment.
I will again add keys to the dump, but with the swap.
in this file add keys on my device version... 263653
if my device does not convert correctly - then next file is added to the version with keys from forum. 263652
How to think? Starts up or not? :pepsi:

[unitycarrental]

I have written dump of NGAKSON 2002.
Still no start.

[unitycarrental]

I think that my dump is damaged.
Can you get me a new dump with added keys in forum?
Amtel 25040

[unitycarrental]

Can I get a immo off file?

[Renovator]

please attach a photo stickers and board immо. I will try to look for the desired information.


after a long time ....
I ask for information - in response to the silence.:sleep:
Okay, let's go another way ....:idea:
tell me:
1) how the immobilizer lamp light, if there is no key in the lock?
2) how the immobilizer light if the key inserted in the lock, but the ignition is not turned on? (especially interesting is extinguished it immediately or after a few seconds, or nothing changes)
3) how the immobilizer light if the key inserted in the lock, and the ignition is on? (blinks evenly, or flashes of long and short)


after 3 hours ...
In well-known Resources, no new dump.
immoff for your car is not possible.
I have decided to restore your dump.
bad that you did not deign to attach a photo sticker of the control unit.
This greatly complicated the task, because in 2005 produced cars with several types of memory, and several record formats keys in them.
I think that this car is a recording method that is not known to me.
Based on the above, and information in internet the seen, I suggest 2 dump for verification.
Their 2 because I do not know in what format the source code specified key from the first topic.
Therefore, the dump was rewritten ..
First dump - keys in the way they title.
The second dump - keys of the title but TIRIS format.
263741
please check them out on the car, and give me an answer. I have worked successfully, or wasted my time.

[unitycarrental]

Thanks for all these effort.
Here are some images of ecu.263758263759263760263757

[Renovator]

Thanks for all these effort.
Here are some images of ecu.

early thanks)). the car still does not smoke exhaust. )))

Your images have confirmed the loyalty of our destinations. Patiently await the outcome of test dumps. And a report on the behavior of immo indicator.

I need to see this information, in your ECU sticker.
263766

[key]

....................

[key]

Hello members,
Please help with adding:
Key 1 :7E C0 BA 50 90 00 00 00 00 A9 3E 7E 00 00
Key 2 :7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00
Key 3 :7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00263335263335

Thanks in advance.
You Transponder key data readed in TIRIS format?

[ngakson2002]

I have written dump of NGAKSON 2002.
Still no start.

Dump i sent to you is Ok and if car doesn't start it may be due to the transponders information you sent.
In fact, check and make sure what you sent is the Tiris Format of the transponder.What are you using as transponder reader?

Regards

[unitycarrental]

I am using Clone King to read transponder data.
I will try dumps today and give feed back.
Thanks so much.

[unitycarrental]

Here are some pic.
89661-5C180





263822263823263824263825

[unitycarrental]

Update:
I have tested files from Renovator security lamps keeps blinking normal with keys in ignition and as I try to start the security light keep flashing.

I test the file of Key.
Enter key in ignition security light keep blinking normal and I try to start,security light solid red but still no start.

[unitycarrental]

Did not work.
Thanks for trying.

[dell66]

Creating Keys for a Toyota Aygo (2005 - 2013) using Touchclone. Lost Keys - YouTube (http://www.youtube.com/watch?v=Ik0M8WEJz6w)

[Renovator]

Did not work.
Thanks for trying.
Please refer to the person who read the information from your keys. Ask him to do it again, and make a screen shot at the end of each key reading. I have the impression that the keys are read correctly .. but not in the format we need. Do it please. We must win this war with immo :ridinghorse:

[unitycarrental]

Thanks for pointing the key data back to me.
There was a mistake with one of them.
I have re-read them and they are:
Key 1 : 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00
Key 2 : 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00
Key 3 : 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00

[bram380]

Hello members,
Please help with adding:
Key 1 :7E C0 BA 50 90 00 00 00 00 A9 3E 7E 00 00
Key 2 :7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00
Key 3 :7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00263335263335

Thanks in advance.

Note:
your dump too big 0000-020F, EEPROM ATMEL AT25040 must be 0000-01FF.

Write this dump and use the Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00

[unitycarrental]

Thanks.

I will try.

[unitycarrental]

I have tried all the above files and none of them worked.
The car still does not start.

[bram380]

Did you use key with code: Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00 ?
Did you select eeprom 25040 while programming?

[unitycarrental]

Yes,I did.

[unitycarrental]

Yes,I did.

[unitycarrental]

Here are the keys and tiris data:
Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00.

Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00.

[ngakson2002]

Here you go mate,
Hope with this dump you have to program in the eeprom will start your car and then thistopic will be closed.

Regards

[unitycarrental]

I will be very happy if this work.
I will try and let everyone know.
Thanks again for all these effort.

[unitycarrental]

I'm very dissapointed to let you know that car still does not start.
This last file the same as you put keys in ignition the light keep blinking.
I there anyway I can get a virgin dump for Fijutsu ecm 89661-5C180 chip 25040.

[ngakson2002]

I'm very dissapointed to let you know that car still does not start.
This last file the same as you put keys in ignition the light keep blinking.
I there anyway I can get a virgin dump for Fijutsu ecm 89661-5C180 chip 25040.

I am sure you have another problem with this car.As far as dump i sent with your key added can't start it.
However attached here is your virgin file.Having program the Eeprom, fitthe ECU back to the car. Insert the transponder key in the ignition switch:the security light will remain solid (learning key) after 2-5s remove the key. Repeat the procedure for the 2nd and 3rd key and then start the car.

If at this stage car doesn't start then check:
1) The Antenna coil located at the switch
2) the key reminder switch

They are also common failure on this car

[unitycarrental]

Thanks.
I have a working car and have tested the ecu with the files and still does not start.
I have program another virgin file as I put keys inside the ignition,security lamp becomes solid red and then start to blink with all 3 keys.
I will load your virgin file and try it.
I'm using a Wellon V-290 programmer
Do I have to do anything with the file you send me other than just dowload and write it to eeprom chip 25040.

[ngakson2002]

Thanks.
I have a working car and have tested the ecu with the files and still does not start.
I have program another virgin file as I put keys inside the ignition,security lamp becomes solid red and then start to blink with all 3 keys.
I will load your virgin file and try it.
I'm using a Wellon V-290 programmer
Do I have to do anything with the file you send me other than just dowload and write it to eeprom chip 25040.

Yes, just download write to eeprom and follow the procedure explained

[unitycarrental]

Thank you.
I will try and let you know.

[unitycarrental]

Wrote the virgin file.
Tried it on a working car.
Security solid red.
key 1 5 sec light blinking
remove key light solid red
key 2 5 sec light blinking
remove key light solid red
Key 3 5 sec light blinking
Try to start.No start.

[yssf]

post the picture of the key tiris read from PC

[unitycarrental]

Here are the keys and tiris data:
Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00.

Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00.

[ngakson2002]

Here are the keys and tiris data:
Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00.

Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00.


Yes Friend

Make the screen shoot of the transponder reading and post here.I strongly believe problem may be the incorrect data.

Thanks

[Renovator]

Please read the error codes in the engine control unit. And tell them here. If not even start working on the car - should be even accompanying Problem. Doubt the correctness of the data were expressed earlier, and not only me. But I think he makes the lack of engine start after recording virgin dump.
Do you have teamviever? Am of the opinion, it is useful to us. And please - read data from the EPROM, after recording virgin dump and manipulation done with the keys. I wonder - immoboks read data from keys and recorded in memory or not? If the recording and manipulation with the keys in the dump significant changes not - then there are additional obstacles to reading data from the key.

[unitycarrental]

I have compared the above virgin dump from NGAKSON and it is good.
Maybe I can get the key date put inside and try.
Key 1:7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.
Tiris data:7E 03 5D 0A 09 00 00 00 00 3A AE 7E 00 00

Key 2:7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00
Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00

Key 3:7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00
Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00

[unitycarrental]

264777
264777
I have read a working car eeprom to compare.

[unitycarrental]

Can someone tell me how to modify the the key data or tiris data in the working car eeprom chip.
Thanks in advance.

[ngakson2002]

264777
264777
I have read a working car eeprom to compare.

Yes this working has some bytes differences with your file.
Attached is this working with your keys data 1 and 2 added.Test and report

[unitycarrental]

Should I just dowload and write to eeprom.

[ngakson2002]

Should I just dowload and write to eeprom.

yes download and write to eeprom.Use key 1 or 2 to start the car


Good luck

[unitycarrental]

Thanks.I will try.

[unitycarrental]

I tried.
The security still blinking and car does not start.

[yssf]

here is the clue mate for this ecu, try and report write your key in dump as in tiris don't change the byte.(use tiris data)
it took me 3 hours to find out the first time,hope it work for you also.(sorry that i can't write it for you cause i'm at home now,i'm sure you can write it yourself,right? lol..)
example below:
Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.
in dump:03 5D 0A 09

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.
in dump:39 5D 0A 09

[unitycarrental]

Do you mean to change 07 06 B3 80 three times in dump to 03 5D 0A 09
And the program back to chip.

[TeL200]

I have just studied this topic and checked all dumps

ngakson2002 (http://www.digital-kaos.co.uk/forums/members/110214-ngakson2002/) has given good files with the correct Tiris for your keys.

But, I think your problem is reading/writing the EEprom correctly.

The EEprom should be read/written as Atmel AT 25040(8) (512 x 8)


The original dump is the wrong file size (528 bytes) with missing data.

The Dave dump is the wrong file size (528 bytes) but with correct data.
(If you write the original Dave dump back to the original working car, will it still start?)

I think the only way forward is to correctly write a virgin file and cycle 3 keys

Good luck

[unitycarrental]

Thanks for this input.
I will re-read Dave dump in 4096 bytes.
Can you tell me how to add the tiris data?

[unitycarrental]

You may have a point there.
I wrote a virgin file and the security lamp is solid red when inset keys it started to blink,but still does not start.
Bo you have a virgin dump for this ecu?

[yssf]

here i add these 2 keys for you in my dump write it to your eeprom,your dump size is too big,
you can see my dump last line end is 0*F0 buy yours is 0*200, when you write my dump re-read the eeprom again to be sure that it keep the same size and the status still the same.
note this:when you put ignition ON security light will stay steady wait 5 seconds turn ignition off-ON and start the car the security light will keep ON after 3-4 start it will off.


Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

[unitycarrental]

Does TEL 200 have a point?

[unitycarrental]

YSSF,
Can you explain which data you changed in your dump?

[unitycarrental]

I wrote YSSF file and then re-read the chip and it has 256 bytes.
Security light solid red.
Put key 1 in for 5 sec then off and then on.
Put key 2 in 5 sec then off and then on.
Try to start security keep blinking and no start.

[bram380]

After review many post & dump, you need to select correct:
- EEPROM type (25040)
- EEPROM size 512 bytes (0000-01FF)
- Transponder 4C (key data & Tiris data)

Use key in list below:
key1:
-----
7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00 -----> (key data)
7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00 -----> (Tiris data)


key2:
-----
7E BD B2 E7 10 00 00 00 00 38 8D 7E 00 00 -----> (key data)
7E BD 4D E7 08 00 00 00 00 1C B1 7E 00 00 -----> (Tiris data)

Write this dump & good luck.

[gwee]

forget about the previous 70 posts, start fresh

just follow bram's instruction :)

[unitycarrental]

7E BD B2 E7 10 00 00 00 00 38 8D 7E 00 00 -----> (key data)
7E BD 4D E7 08 00 00 00 00 1C B1 7E 00 00 -----> (Tiris data)
Thanks.
I do not have this key.

[bram380]

Any key 4c can add to dump.
But first try this dump and use below key:

key1:
-----
7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00 -----> (key data)
7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00 -----> (Tiris data)

[unitycarrental]

Thanks.
I will try.

[unitycarrental]

Very dissapointed to let you guys know that nothing worked so for.
I will keep trying.

[bram380]

Read again eeprom after failed and compare them (dump before & after write).
or post here the dump.

Maybe you have 3 choice to start the cars:
- call locksmith near your area:driver:
- bring the cars to dealer:driver:

- try, try and try.... :banghead::giveup::beheaded:

[yssf]

mate you must have another problem in your car.(with my dump the car start while security light keep blinking and off after 3-4 start, in all keys lost situation)
check the reminder switch on ignition,"can you hear a beep when insert the key IN and driver door opened?"
or try another antenna on ignition barell.

you can also associate a closer dk member to fix it,lol..

[unitycarrental]

265080
I will create another dumpwith tiris data.Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00.

Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00.

Can you tell me if this is good.

[ngakson2002]

265080
I will create another dumpwith tiris data.Key 1: 7E C0 BA 50 90 00 00 00 00 5C 75 7E 00 00.

Tiris data:7E 03 5D 0A09 00 00 00 00 3A AE 7E 00 00.

J


Key 2: 7E 9C 4A 50 90 00 00 00 00 A9 3E 7E 00 00

Tiris data:7E 39 52 0A 09 00 00 00 00 95 7C 7E 00 00.

Key 3: 7E D7 C9 30 90 00 00 00 00 A5 22 7E 00 00.

Tiris data:7E EB 93 0C 09 00 00 00 00 A5 44 7E 00 00.

Can you tell me if this is good.

Hello Mate,


Just follow yssf suggestions check The Antenna coil and the key reminder switch both located at the ignition switch barrel.They are also common failure on this car.

Also the easiest way will be to Plug this mike ECU where you got this dump to your car and see if will start.

Good luck

[siyadk]

i agree with ngakson2002...yaris is known for its key reminder switch failure...Well not yaris , pretty much all toyota cars

[ngakson2002]

Hi

Have here test procedure of the items listed

[unitycarrental]

Thanks again.
I have been trying the ecu on a working car.
When I try the one I working with the immo light is solid red and then start to blink with all 3 keys.
Everytime I take out the keys the light is solid red and after 2 sec starts to blink.
When I plug in the working car ecu it starts right await with its own key.
So I do not think I have any other problem but the immo in the ecu.

[gwee]

clone everything from working car and is done

[unitycarrental]

Sorry,do not have clone chip.
I have created a virgin dump from the working car.
I have created a bosch 25040 and a Fujitsu 25040 virgin dump.
When I compare them there are a little difference.
I think that is my problem.
All the dumps I receive on this forum are Bosch 25040.
I will try tomorrow and post.
Thanks for all these help.

[ngakson2002]

Thanks again.
I have been trying the ecu on a working car.
When I try the one I working with the immo light is solid red and then start to blink with all 3 keys.
Everytime I take out the keys the light is solid red and after 2 sec starts to blink.
When I plug in the working car ecu it starts right await with its own key.
So I do not think I have any other problem but the immo in the ecu.


Hello Mate

At this stage i am not sure that the transponder data you have been posting here is really the TIRIS DATA.Read the transponder and attached here the screen shoot.(real picture as shown on your PC or transponder reader screen


Regards

[unitycarrental]

Thanks for all those help.
Very much appreciated.
Car started will all 3 keys with some help with abrites toyota commander.
Thanks again to all and a special thank you to NAGASON 2002.

[ngakson2002]

Thanks for all those help.
Very much appreciated.
Car started will all 3 keys with some help with abrites toyota commander.
Thanks again to all and a special thank you to NAGASON 2002.

You are welcome.However,Thanks is given by Clicking on the corresponding Thanks at the left hand under your user ID.I foreseeing many who help you will appreciate if press this for at least one of their replies.

[unitycarrental]

Once again.
Thanks to everyone.

[unitycarrental]

266325

Hello mate.
See attached 25040 virgin dump.

[mra999]

Buy Some Original Tool To Make Program Correctly As Tango

[gwee]

Buy Some Original Tool To Make Program Correctly As Tango

If tango can solve this car, u think this thread will be so long??

[mra999]

Not About Solve Or Unsolved To Read Correct Key Info Yes , Easy to Work With Tango and Lot of information He can Collect , He can Learn More info Adding Keys , Location . I think Tango Is Very Strong Tool in Market , Never will come any of machine that can do all job Done , Not about only Tango But to get Information / Root yes machine can Give you , Machine Can Help you ,Why Should We need machine? Yes To Make easy our Job .

why i said like that to buy some machine Because((((((( ​unitycarrental))))))) said I am using Clone King to read transponder data.
I will try dumps today and give feed back.))))))))