View Full Version : problem Golf R32 me7.1.1
moky
12th July, 2014, 08:41 AM
hi
after bad obd flash,i dessolder reflash 29f800 but car don't start and fan is On..
a friend say me problem e2prom..problem is in 5P08?
someone know this problem and how to repair it?
many thx!
milanocito
12th July, 2014, 09:57 AM
remove fan fuse
and do do read ecu after that write file i iuse this on galletto
wiski
12th July, 2014, 08:06 PM
If you can connect it with vcds and have cheksum error on 01 engine then yes you have corrupted eeprom. If you cannot connect then you have bad flash try to rewrite it in boot
Sent from my GT-I9100
moky
12th July, 2014, 09:42 PM
thx all
I have checksum error..someone can repair eeprom?
milanocito,you think your solution will work ?
thanks
milanocito
12th July, 2014, 09:58 PM
it is worked for me 3 times
when i trayed to write without doing red ecu it is fails
when i did red ecu and write ecu it done
the same ecu i have me 7.1
wiski
12th July, 2014, 10:00 PM
It's mk4 or mk5 ? What are ecu nr
Sent from my GT-I9100
moky
13th July, 2014, 08:38 AM
it's an mk5
022906032GP
0261201805
389049
thanks
carmageddon
13th July, 2014, 10:09 AM
it's an mk5
022906032GP
0261201805
389049
thanks
if need compare your readout this is original file of your ecu
read pm if need!
268376
woodysjw
13th July, 2014, 10:13 AM
you need to repair the eeprom ive had this and used a virgin eep and recoded back to car
moky
13th July, 2014, 10:30 AM
thx
no posible to repair eeprom directly?
i don't have car here....:blue:
moky
13th July, 2014, 10:31 AM
if need compare your readout this is original file of your ecu
read pm if need!
268376
thanks i will look
moky
13th July, 2014, 10:34 AM
just look and original file is good so it's eeprom for sure..
carmageddon
13th July, 2014, 10:46 AM
not only e2p can do your mistake, also mpc can loose data via boot mode or obd, if your problem is on mpc you can only buy another ecu with same HW and SW and try to exchange e2p.
wiski
13th July, 2014, 01:29 PM
If mcu is faulty he couldn't connect ti vcds for sure. This have sort of death code in it.
Sent from my GT-I9100
wiski
13th July, 2014, 04:32 PM
Here you have eeprom that should work for you.
moky
14th July, 2014, 12:48 AM
Here you have eeprom that should work for you.
thanks wisk I will take a look and apply..i tell you informed
many many .. thanks for help :top:
moky
14th July, 2014, 12:52 AM
double post sorry..
moky
15th July, 2014, 03:32 PM
i just read 95160 someone can take a look and say me if corrupted..it seems no but..
thanks!
moky
15th July, 2014, 03:47 PM
i will test wisky file
ominimicu
16th July, 2014, 09:06 AM
I remember when i flashed my first R32. USing MPPS. it wrote..ok and car did not start...tried bench flashing, boot mode eerything.
Finally i i rewrote ori file slecting Proche chayenne...wrote in 5 secs..did a checksum verification and worked!
dunno why i was a noob back then.
moky
16th July, 2014, 11:57 AM
thx ominimicu but all that tested and it's not my first r32.. just bad luck..:joyous:
moky
16th July, 2014, 07:33 PM
Here you have eeprom that should work for you.
car run fine wisky many thanks for help !! :top:
ominimicu
16th July, 2014, 07:43 PM
SO it was a eeprom problem?
moky
16th July, 2014, 07:48 PM
yes it was..
ominimicu
16th July, 2014, 07:54 PM
damnniitt...i am curious why OBD flashes affect eeprom, it happens even on edc17,,problem is no eeprom checksum unless we have original winols
moky
16th July, 2014, 07:55 PM
checksum made with official ols ..
jezzag60
15th December, 2016, 10:06 AM
Do you have the working Eeprom for this? I am having a similar problem with the same ECU - I have a corrupt Eeprom
moky
15th December, 2016, 10:14 AM
here eeprom file pass in pm
moky
15th December, 2016, 10:00 PM
beautiful jezzag60..no hello..no thanks ....no.... so Fuxxxxxxxx man Go away
DK is not a SELF service ..your ass perhaps...
and if you need nothing tell us , Dk member !!!!!!!!!!!!!!!! :D We will be there
Apsik
16th December, 2016, 09:38 AM
I work with this ECUs a lot. I never flash ME7.1 or 7.1.1 (VW VR6) via OBD. It does not work.
markpowell35
26th January, 2019, 08:50 PM
Here you have eeprom that should work for you.
Hi i am facing same problem after write by obd, drive car switch off, will not start again, Checksum error.
I have boot mode reads of mpc e2p & flash with Ktag protocol 50 Vag 7.1.1 HW 1
But cannot write anything to flash so i need to fix eeprom but what needs to be changed?
Eeprom attached any help much appreciated.
Mark.
wiski
26th January, 2019, 09:02 PM
Hi i am facing same problem after write by obd, drive car switch off, will not start again, Checksum error.
I have boot mode reads of mpc e2p & flash with Ktag protocol 50 Vag 7.1.1 HW 1
But cannot write anything to flash so i need to fix eeprom but what needs to be changed?
Eeprom attached any help much appreciated.
Mark.
Hi , sorry can’t help you till monday
Sent from my iPhone using Tapatalk
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.