VAG K+CAN COMMANDER 3.6 HELP

[WOODWARD395]

:joyous:Hi been using vag k+can commander 3.6 for dtc's the only problem its half in broken English and the rest in German but translated by a Chinese person to German so if I use Google translate it cannot as its not translated to German very well so gives you a load of crap.:blue:

does anyone use any software that works with this cable that's in English.
was going to pay out for a decent setup but off sick now and funds are tight.

software if anyone can change to English would be fantastic.

270465

[smokey08]

You have brought the wrong cable for reading faultcodes. It is only good for reading pincodes + mileage correction on ancient VAG cars.

Get yourself VCDS. (if things are really tight a clone cable with slightly older software costs about ?15)

[super jumbe]

:joyous:Hi been using vag k+can commander 3.6 for dtc's the only problem its half in broken English and the rest in German but translated by a Chinese person to German so if I use Google translate it cannot as its not translated to German very well so gives you a load of crap.:blue:

does anyone use any software that works with this cable that's in English.
was going to pay out for a decent setup but off sick now and funds are tight.

software if anyone can change to English would be fantastic.

270465


In English tested mate.

[smokey08]

Faultcodes still in ze deutsch SJ.

You could waste your life converting hex to decimal and writing faultcodes in english into the VAG.txt file

e.g. Faultcode 17645
17645 convert to hex = 44ED
Change: "44ED Einspritzventil Zyl.1-N30 Unterbrechung" to: "44ED Fuel Injector Cyl.1-N30 Open Circuit"

[super jumbe]

Mine working in English ok, maybe they need to change computer language!!

[betrescudan]

hmm.....german cars....germans dtc

[speedy100]

Hello,

What cable is this working with as I have version 2.5 and it works with Blue "VAG K+ CAN" cable.
Or VAG KKL+ bue adjustable cable but version 3.6 does not see them...
Any ideas?

Best Regards

[Keithuk]

e.g. Faultcode 17645
17645 convert to hex = 44ED
Change: "44ED Einspritzventil Zyl.1-N30 Unterbrechung" to: "44ED Fuel Injector Cyl.1-N30 Open Circuit"


VAG Error Code: 17645
EOBD II Error Code: P1237

Fault Location:
Fuel Injector for Cylinder 1 (N30) - Open Circuit

Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Poor engine performance.

Fuse for injector.
Wiring harness issue.
Failed injector.
Failed Engine Control Module (ECM).

Possible Solutions:
Inspect fuse for injector.
Inspect Wiring/Connector(s) to and from injector, see repair manual.
Ohm test injector, replace if needed, see repair manual.


As taken from my EOBD II Fault Codes software which you can Google.

[smokey08]

As taken from my EOBD II Fault Codes software which you can Google.
[/SIZE][/FONT][/LEFT]


Looks to me like it was stolen from the rosstech wiki.

Do you have permission to copy their work?

[WOODWARD395]

In English tested mate.
my pc keeps deleting it as it says it is a virus. When I eventually got it to install still in German.

[WOODWARD395]

You have brought the wrong cable for reading faultcodes. It is only good for reading pincodes + mileage correction on ancient VAG cars.

Get yourself VCDS. (if things are really tight a clone cable with slightly older software costs about ?15)
Cannot find any cheap cable for vcds that does mk 5 golf 2006 only up to mk4 or am I missing something.

[speedy100]

Hello,

What cable is this working with as I have version 2.5 and it works with Blue "VAG K+ CAN" cable.
Or VAG KKL+ bue adjustable cable but version 3.6 does not see them...
Any ideas?

Best Regards