PDA

View Full Version : Original eeprom a6 c6 2.0tdi BRE



qplanetq
2nd August, 2014, 03:43 PM
Welcome. Needs original eeprom immo off and dpf off to audi a6 c6 2.0tdi BRE, 03G 906 016 MF , 2007r EDC16U31. Will help someone?

qplanetq
3rd August, 2014, 02:47 PM
Maybe someone has an EEPROM from Immo off?

qplanetq
5th August, 2014, 05:52 PM
Maybe someone has an EEPROM for this EDC

qplanetq
6th August, 2014, 04:29 PM
Can someone check if this is eeprom immo off


http://speedy.sh/6hyYv/immo-off-a6

bobolin4o
6th August, 2014, 05:26 PM
271796

Immo is off.
Cheers!

qplanetq
6th August, 2014, 06:02 PM
02229 - Transmission Control Module (TCM); Immobilizer Data not Adapted what is it
?

bobolin4o
6th August, 2014, 07:29 PM
I think, you should explain better all situation, so somebody help you...
What exactly happened with this car?

qplanetq
6th August, 2014, 10:47 PM
I changed gearbox with driver is probably the protection component. what to do? multitronic gearbox

qplanetq
17th August, 2014, 10:36 AM
Has anyone can charge original eeprom to 2.0tdi BRE?

qplanetq
8th October, 2014, 09:38 PM
Anyone have eeprom for 03g906016mf for manual gearbox? Please help

bobolin4o
9th October, 2014, 10:22 AM
You need Full BDM dump, not only EEPROM, from car with manual gearbox, then make immo off...
Regards!

qplanetq
9th October, 2014, 03:40 PM
Ok anyone have it?
may be of immo on

qplanetq
9th October, 2014, 03:49 PM
Or, maybe you know how to change the encoding from automatic to manual ? All drivers encode on the manual . edc do not want to encode .

bobolin4o
10th October, 2014, 05:58 AM
No way to encode EDC, the software is specified for auto, or manual, etc... and is peer of MPC, EEPROM and flash.
Search for full BDM, flash the ECU with immo off... this is the right way.
Regards!

bobolin4o
10th October, 2014, 06:22 AM
This is what i found... it's full BDM read from ECU, manual transmission, WITHOUT DPF from factory...
Good luck...

I put and eeprom file with immo off.
Regards!

qplanetq
11th October, 2014, 01:25 PM
Thank proof, and I will know that works .

qplanetq
11th October, 2014, 08:08 PM
My EDC is damaged BDM connector . MPPS will do the trick ?

bobolin4o
13th October, 2014, 06:18 AM
I have nothing else to say...
Load those three files trough BDM port (MPC, flash and eeprom with immo off), make checksum with BDM programmer!
If BDM port is dameged... then nothing to do about.
Find ECU with HW 0281014258 - MT, with DPF, or 0281014261 - MT, without DPF, make immo off, job done!
Regards!

qplanetq
13th October, 2014, 02:36 PM
Bdm read my eeprom , internal flash and external flash . You sent me a file MCU . I do not know where to write it because in bdm I have 3 options iternal / external flash and EEPROM . What is your MCU have submitted ?

bobolin4o
13th October, 2014, 03:37 PM
Obviously "MCU" is the internal flash...
Regards!

Hm... don't forget to save backup of your current software...

qplanetq
13th October, 2014, 03:43 PM
ok but my internal flash have 512kb and your have 256kb?

bobolin4o
13th October, 2014, 03:45 PM
Post here the three files, readed from this ECU.
And which exactly is your BDM?

qplanetq
13th October, 2014, 03:51 PM
all from bdm my edc16 a6 c6 2.0tdi ori.rar - Speedy Share - upload your files here (http://speedy.sh/6VYbv/all-from-bdm-my-edc16-a6-c6-2.0tdi-ori.rar)

This is my full bdm dump

qplanetq
13th October, 2014, 03:52 PM
And i have clone fgtech 2

bobolin4o
13th October, 2014, 04:26 PM
So, as i see, my MPC file isn't like yours...
Maybe i can extract it from .sgo file...

bobolin4o
13th October, 2014, 05:33 PM
Finally... i did for you full BDM set (flash, mcu, and eeprom with immo off), software for 0281014261.
Give it a try!

qplanetq
13th October, 2014, 06:27 PM
Dear friend . Ive loaded sent files . After uploading VCDS does not want to communicate with the motor controller . Ive loaded first external flash and bdm counted for checksums . Later ive loaded internal flash bdm then showed news from the conversion does not support checksum for the flash . Later ive loaded EEPROM . Unfortunately, the engine does not start. Something I do wrong ?

qplanetq
13th October, 2014, 06:31 PM
I do not know already what to do .

bobolin4o
13th October, 2014, 08:01 PM
Don't know what to tell you more.
First i found those files from other tuning community, but mcu file is totally different from yours.
Then i extracted flash and mcu files from SGO file ( vag update cd, exact software number )
Unfortunately mcu file (update) isn't complete (FFFF at beginning of file) and i pasted content of your file there. WinOls made checksum correction...
Obviously, this is not the right way, or my knowledge ends at this point... and you must to find the REAL full bdm, or ECU with right soft in it.
Regards!

betrescudan
13th October, 2014, 08:20 PM
Welcome. Needs original eeprom immo off and dpf off to audi a6 c6 2.0tdi BRE, 03G 906 016 MF , 2007r EDC16U31. Will help someone?
MAYBE THIS IS REALLY WHAT YOU NEED...BUT MAKE IMMO OFF

qplanetq
13th October, 2014, 09:22 PM
Now bdm send me information when i connect " error micro not supported ....

betrescudan
13th October, 2014, 09:27 PM
Now bdm send me information when i connect " error micro not supported ....
are you blind?---i posted a file for you with your ecu...is good or not?

qplanetq
13th October, 2014, 09:30 PM
After the last uploading files uploaded by you BDM not already connects with EDC

qplanetq
13th October, 2014, 09:35 PM
file is good

qplanetq
14th October, 2014, 03:10 PM
Can I adapt edc from 3.0tdi to 2.0tdi?

qplanetq
14th October, 2014, 03:14 PM
Maybe i can adapt edc from a4 b7 2.0tdi ?