bmw ms45.0 need info for sync.

[gttuning]

hi guys have a bmw e60 petrol ecu DME MS45.0 5WK93016 ,never workd on this.
need info what need to do to get this ecu ready for syncro.
inside st95320 and flash AM29BL802CB.
I attachment all read from ecu.
Thanks for any info,will save me time:)

[rex89]

hi mate, u need read immobiliser and post it here (cas or ews ) for check ISN then synch it after write.

[gttuning]

hi mate, u need read immobiliser and post it here (cas or ews ) for check ISN then synch it after write.
ok will read ews or cas.

[gttuning]

hi guys,here is cas read out.
can some one try to get this ecu ready for syncro.?
Thanks

[rex89]

hi mate ,write this into u cas , be sure that u make good writing after just synch and start car:joyous:.
les us know result
pass in u pm already
BR

[gttuning]

Hi tryin to write this file with xprog but cant write.it will read after few times of tryin but wont fu...write in.any info if xprog works on this mcu in cas2?

[rex89]

hi mate , umm think that u will make read with rosfar RS260 , with xprog u need make good diagram we need know u mask for help yu then,
0L15y ? 9S12 DG256 ? 128 ? 64??? post infos here if u need help
BR

[gttuning]

MC9S12DG256 MASK 2K97X.
it will read flash and epp. after few times but im stuck with writing to epp.
some times will write but at the end verify error.and some time will not pass security bypass.

[gttuning]

well any body knows if xprog is fit to write cas2?

[rex89]

Hello mate , i dont know if u make error with mask but seem that cas2 have 2K79X and not 2K97X
where is the fault me or u ? so i make little diagram that i try already for a car e90 today for make sync
read/write by xprog at 100% without problem check picture(if not work after all information that i give u better use rosfar or change cas2) , make it , write u file and go to start u car after good synch.
Best regards

[gttuning]

Hi REX89 i done the way xprog manual shows,but your foto is different.ar
I will try that and see,hope will work.
where can i get good rosfar programer?

[bali motor]

this virgin file for ecu... just syn your ecu

[gttuning]

this virgin file for ecu... just syn your ecu
will try man.but first give me pass.

[junnnior]

hi pass please

[bram380]

post here original dump dme & cas

[MARIUSZBMW]

Hello, I am looking for a virgin flash for ms45 can anyone have?

[vasua]

bali mootor
password for virgin file?

[leandroks]

Hi guys i ve got and X3 wich dme got stolen.
So i need to adapt new (donnor) dme.
Could anyone help on doing that??
It is ews3 and ms45 dme

Thanks in advance

[kiszka]

Hi guys i ve got and X3 wich dme got stolen.
So i need to adapt new (donnor) dme.
Could anyone help on doing that??
It is ews3 and ms45 dme

Thanks in advance

https://mega.nz/file/c3hF2QbT

[leandroks]

Thanks a lot mate but i tryied to sync and it shows me the message not supported on dme . any idea??

[kiszka]

Thanks a lot mate but i tryied to sync and it shows me the message not supported on dme . any idea??

you performed synchro towards the ecu or EWS

[CoKolWiekkk]

this virgin file for ecu... just syn your ecu
can i get the pass?