pcr 2.1 problem with v54 galletto

[kospoz]

Hi everyone i hope that someone can help me because my head will explode!
I tried for 6 hours to read one pcr 2.1 from octavia 1.6 cr but nothing.
I have unlocked it with galletto v53 because with v54 i could not.
I bought the v54 because the v53 had problem with can bus the v54 is working good with this.
The next step was to read it via obd the software read the ecu id and when was starting to read sometimes at 6% 17% and the biggest 51% stopped with error!
Ok lets read it with boot mode but nothing and there.The fault is wake error boot error.Any ideas please people?

[gttuning]

what version of galleto chine or europa

[smayer]

Galleto read and write by OBD, if your?s don?t then change it.

[kospoz]

i bought it from Greece and he said that is eu tool number 0386

[kospoz]

Galleto read and write by OBD, if your?s don?t then change it.
problem with the hardware?
i will test it tomorrow with edc17c46 bootmode to see if can work with this

[kire106ka]

problem with the hardware?
i will test it tomorrow with edc17c46 bootmode to see if can work with this

you have a china clone

[kospoz]

you have a china clone
i must ask for refund my friend?

[b2s15]

eu clone v54 is working great on this ecu.
read-write-unlock

[pablo1971]

how did u unlock the eeprom...did u mod the board,or remove the eeprom.??

[b2s15]

unlock is done by bootmode with v54

[gttuning]

how did u unlock the eeprom...did u mod the board,or remove the eeprom.??
if its galletto last update its boot mode to unlock
galetto2 eep.corection.

[blazej1200]

eu clone v54 is working great on this ecu.
read-write-unlock

I confirm galletto V54 eu clone works perfectly with the ecu

[dean 21]

Hi, even if the ecu is not unlocked you can read the file and you can write the same file.

[kospoz]

The galletto start reading data file and at 10or50% of progress stops.
I saw that in the obd cable has not resistor at can line

[masterb]

The galletto start reading data file and at 10or50% of progress stops.
I saw that in the obd cable has not resistor at can line

for only reading, eeprom unlock is not necessary !
So problem is not unlock .. think bad clone hardware
only for write tune file, eeprom dump is importend !!

[koyot]

eu clone is fake
no read ppd no k/line etc etc
psa hdi edc16 not work and and pufff
should not be more that goes

[kospoz]

i have v53 too i bought it from china.This can unlock pcr2.1 but it can not read it with obd is not starting at all.I saw that in this cable exist a resistor 120 but in obd of v54 there is not any resistor.
In boot cable exist one resistor but 220 not 120 maybe if i will change from 120 to 220 solve my problem?

[ruscic]

i have china v54, works fine on pcr.

[morgano]

i have v53 too i bought it from china.This can unlock pcr2.1 but it can not read it with obd is not starting at all.I saw that in this cable exist a resistor 120 but in obd of v54 there is not any resistor.
In boot cable exist one resistor but 220 not 120 maybe if i will change from 120 to 220 solve my problem?

If you unlock ok in boot, but after fit in car you cannot even id the ecu, then your v53 has faulty canbus.


Regards,

[kospoz]

If you unlock ok in boot, but after fit in car you cannot even id the ecu, then your v53 has faulty canbus.


Regards,
Ok i see there is a solution for this?

[morgano]

Normally mcu changing with a working one.


Regards,

[kospoz]

i must buy one mcu and put it on nothing else?
This mcu want to be programmed or something else or it is ready for use?
Thank you

[morgano]

Mcu need to be programmed with fgtech fw, of course. It is the brain of the interface.

[jojo1212]

galletto v54 china is very bad, most of time it dont work