VW Golf 6 Dash Magneti Marelli NEC+95320

[Rito]

I try done this dash but It now is some dead..
I use enigma for do it.. Now dash only have small light and any pointer don?t work.
Anyone know about??

This is process...
277419


Thanks

[Dashcoder-Alexander]

device maybe still in boot mode.
replace the first area off eep with data from working cluster.
always make a copy of eep before trying this on a magneti marelli device.
in all other cases flash is erased but not written correctly...reflash

use a charger voltage under 11 volts means flash can only be erased and not written #
nice to see that other devices have the same problems with italian s....

[lupu_sandu]

Post part number. I have flash and eeprom from few dashes.

[Rito]

Ok, thanks, part number:
MM7
SW: 0310
HW: H33
5K0920872A

277582

Thanks

[lupu_sandu]

5K0920872A
Collection of NEC flash and eeprom. Also immo data is saved.
Pin,CS,MAC and keys are in .png file.
Good luck.

[peter1977]

what is pass for archive

[pPeter]

if you have saved orginal eeprom data (even by obd2) just try to program it C4 cable, it should wake up instrument cluster

[jmcartec]

Hi lupu_sandu

may i have the pass for the files you posted here?
I am in troubles with a dash exactly the same, just the HW =33,
my dash works well, just never switch off the background and then
the battery goes down by night

I have beeprog, i think i can use it for nec mcu

[Rito]

5K0920872A
Collection of NEC flash and eeprom. Also immo data is saved.
Pin,CS,MAC and keys are in .png file.
Good luck.

Now its happens again...Last time car got to dealer...
How I can write new flash and programme it to car??


Thanks

[yugo45]

Now its happens again...Last time car got to dealer...
How I can write new flash and programme it to car??


Thanks
SMOK J-Tag can read/Write this Flash, option 9.
SMOK (http://www.smok.com.pl/index.php?lang=en&id=oferta&kategoria=3&produkt=65)
Also X-Dash can do this dash with help of the J-Tag.

[lupu_sandu]

If this Golf have engine 1.6 TDI anD you destroy dash eeprom, only solution is dealer.
If you have EDC17 or MED17, then you can read CS,MAC,Pin from ECU, find 7th byte from working key, put my files in dash with Jtag, then edit dash with AVDI.

[Rito]

Thanks for help, This Time I use DP3 (elprosy) and it Kill dash near end 100% programming....
last time was enigma, so this brend off dash is complicate to do....

[antibisic]

Thanks for help, This Time I use DP3 (elprosy) and it Kill dash near end 100% programming....
last time was enigma, so this brend off dash is complicate to do....


Obd or manualy?Does it hapened to somebody with digiprog?

[lupu_sandu]

Thanks for help, This Time I use DP3 (elprosy) and it Kill dash near end 100% programming....
last time was enigma, so this brend off dash is complicate to do....
AVDI support this dashboard via obd2 now, but takes over 40 minutes to program.
Is much safer and quicker to remove dash and make odo with Jtag from smok.


Obd or manualy?Does it hapened to somebody with digiprog?
No, simply because Digiprog don't support this dash.

[autofan1965]

If this Golf have engine 1.6 TDI anD you destroy dash eeprom, only solution is dealer.
If you have EDC17 or MED17, then you can read CS,MAC,Pin from ECU, find 7th byte from working key, put my files in dash with Jtag, then edit dash with AVDI.

You cant still make it because in dash was 12byte not 7. Dealer or new transponders only.

[antibisic]

No, simply because Digiprog don't support this dash.



Smok xcan suport this dash obd?

[lupu_sandu]

X-CAN and you must have jtag with NEC option activated.

[yugo45]

Picture says everything:

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=292436&stc=1

[EPROMIX]

this shows that also has problems !!

[antibisic]

this shows that also has problems !!


Yes,what about carprog it has obd option.Thats mean that noone tool works with this dash without problems

[yugo45]

this shows that also has problems !!


Yes,what about carprog it has obd option.Thats mean that noone tool works with this dash without problems
With X-Dash some dash you can do only via OBD , do not need J-tag( I think very early models.), but if KM show error or sometimes it will not change Km, then you need to use J-tag.

[antibisic]

With X-Dash some dash you can do only via OBD , do not need J-tag( I think very early models.), but if KM show error or sometimes it will not change Km, then you need to use J-tag.


But it is too late if eror is on the dash,dash dead isn,t it?

[yugo45]

But it is too late if eror is on the dash,dash dead isn,t it?

I would say yes, you can write good flash and eeprom then adopt cluster to car.
Best way on any dash is to read Immo block before you do and Km. After that you safe because you can back up any time with other files or other dash.

[autofan1965]

But it is too late if eror is on the dash,dash dead isn,t it?

I havent done it but from description error should left when you make steps with flash.

[deltona1]

Hi, can you please send pass to rar.? thanks

[ESER]

please send pass to rar.? thanks

[ricards99]

hi all,
i have same probleme with same dash ( same hard and same soft numbers) please mr lupu can i have pass
i have smok jtag and smok uhds i would like to repair with then immo data i will read from pcr2.1
thank you

[bencheacata]

Hi Lupu Sandu ... can you give me the pass for archive? A lot of thanks in advance👍🏻👍🏻

[Pablo98]

Hi Lupu Sandu,
have same dash 5K0920872A Mag.Marelli
after flash frf via VCP cluster death.
Please send me pass for your file.
i try direct flash nec via UPA-S
security block it contains in the Nec?
Thanks Pablo

[ecarruda]

Can you send the Password of this file?

[ramzic200]

salut pass svp

[lumetan]

pass plis!!!

[lumetan]

pasa por favor

[smtncr01]

salut pass svp
pass plis!!!

[kamel2003]

please send pass to rar.? thanks