HYUNDAI TERRACAN 2.9 CRDI 39101-4X740 ORI dump

[mario313]

I need original full dump this ecu DELPHI DDCR 39101-4X740 sw: C7K63SA3 .

Thank you very much.

[Fec001]

I need the same full read dump from 29F200BB.

[icezero2010]

I need the same full read dump from 29F200BB.


you can do boot mode processeor is c167

[Fec001]

Yes, i know but tried to write the "tables" 40 kb file and ecu dead

[icezero2010]

Yes, i know but tried to write the "tables" 40 kb file and ecu dead

upload both files

[icezero2010]

Yes, i know but tried to write the "tables" 40 kb file and ecu dead

upload both files or test this this is full file for automatic335104

[Fec001]

Here are dumps. Full read after ecu crashed and only tables

[icezero2010]

Here are dumps. Full read after ecu crashed and only tables


your file write with boot

[Fec001]

Thanks!!! I was thinking about the same solution :)

[Fec001]

File is ok I think, ECU can wake up (check engine light is on now) and can connect with diag but doesn't start. 1 DTC:
P1300 Injector classification
Control unit error

EDIT:

Injectors recoded, DTC gone but still no start...........
In measuring values no RPM and rail press while cranking.

[Fec001]

With this dump, car can start but ECU reject injector coding. Idle at 1300 and no accelerator pedal.
DTCs:
P1300 injector coding
P1780 engine torque reduction

[Fec001]

Any idea??

EDIT:
Found the problem. eprom 95080 is totally bad. Immo lamp doesn't light

[Harrycz44]

Hi
pleas help me, I have some problem, read table flash 40 kb OK, write not.. got error, car dont start now, I solder flash out and read with programmer........ is possible got table files 40 kb and programmer files together for complete? Thanks for help

EDIT: I look for some software number, I compare files and not 100% some one block is missing, car show correct SW version but dont start, diagnostic show DTC 1300 o(

[Harrycz44]

I try got this two files together ( crashed files from 29F200 and table read 40 Kb) Pleas control it that is OK, Car still dont start (Immo lamp dont light) Thank you

[Fec001]

Use the complete file what I got from Icezero2010. Write with boot and teach in keys.

[Harrycz44]

Teach key and car start now, but RPM is 1300 and no accelerator pedal. I try recoding injector as you said..

[CIRCUIT.FR]

hi

how have you repair eeprom?

thx

[etpvn]

Hello Which tool to Teach Key?

[trotyl]

Hello Which tool to Teach Key?Look info about "cascade " emulator for Windows. One Time i had same problem but this simple program + kkl vag interface let me fix it. Also if somebody maybe need I have 100% working more power file .

Wysłane z mojego SM-G935F przy użyciu Tapatalka

[etpvn]

Hello
I need it
But i dont have KKL Vag Interface.
Can I use Tactrix Openport 2.0 or others Interface!

[Landydoctor]

Hi Fec001 how did you go to resolve your issue with the immo lamp off... I have a Terracan that I flashed with a stage 1 file with kess v2 and lost key programing immo light off.. I flashed std file back original from vehicle that drove and still no immo light and diag says 0 keys and status is virgin virgin.. I also tried limp mode and it doesnt want to go to limp mode to start from immo setup in diagnostic machine. Any advise will help Thanx in advance. Regards

[kamikazeeee12]

Can i have the file as well from icezero as it's gone.

Anyone can help?