View Full Version : 95160 EEPROM
adam28
8th July, 2009, 05:31 PM
Hi
I need to do a immo off on a renault Clio the chip is a ST95160.
I have a X-prog-t, but its not compatible with this Eeprom.
Does anyone know of a programmer that can do this? Preferably not to expensive, and in circuit if possible
Thanks for any help.
Regards
Adam
boorawchick
8th July, 2009, 05:40 PM
Try to read as 25160
adam28
8th July, 2009, 05:59 PM
Thankyou mate i will try this.
Have you done this before then?
boorawchick
8th July, 2009, 06:05 PM
Thankyou mate i will try this.
Have you done this before then?
Sure, I've done it before...
boorawchick
11th July, 2009, 12:34 PM
adam28, any success?
adam28
11th July, 2009, 12:55 PM
Not yet mate im trying to do in circuit.
Ive opened a new thread on this maybe you can help.
Cheers
Aniskey
30th September, 2009, 06:02 PM
omega M programmer is the best programmer to do it
Babanovski
30th September, 2009, 07:13 PM
wher i can bay omega programer
dimitar
5th October, 2009, 02:02 AM
Seeprog the best 8-pin programmer
aeroyas
6th October, 2009, 04:55 PM
yes see prog is a very good one, you can also try with labtool 48-X, very useful for this type of eeproms
kool_mi
15th October, 2009, 06:11 PM
THE GOOD programmer FOR THE EEPROM AND FLACH IS BEE PROG 400UDS AND OMEGA ORANGE MR ADAM
angmar
17th October, 2009, 09:13 PM
HELLO I USED PONYPROG OR UPA USB PROGRAMMER FOR THIS MEMORY
conan981
19th October, 2009, 04:17 PM
for all the usuals eeprom/pic read/write operations i can suggest willem (with eprom45 as software). It is under 100$ and support by many soft and has many adapters for incircuit programming.
Anyway SI-prog is OK (with ponyprog as software) and is more cheap than willem. I buy this device from bulgaria for 20$ shipping included.
just my 2pence :)
martin292009
6th May, 2010, 12:01 AM
eeprom remove the plaque and read with upa-usb
vrsc
6th May, 2010, 12:20 AM
Seeprog is very good for 8 pin eeprom and not to expensive.
maaxxyy
20th May, 2010, 02:49 AM
I use GQ-3X usb Programmer for this.
turkay06
20th May, 2010, 04:39 PM
hı program herehttp://rapidshare.com/files/389609559/25160-95160_program.rar.html
sabe
20th May, 2010, 05:07 PM
Very cheap and simply is PonyProg :-)
antioqueno
16th August, 2010, 04:44 PM
THE GOOD programmer FOR THE EEPROM AND FLACH IS BEE PROG 400UDS AND OMEGA ORANGE MR ADAMhello i need the software for the programmer omega orange i lost the cd plis is urgent
sato-bmw
17th August, 2010, 03:15 AM
You can also use the willem
dimitar
25th August, 2010, 05:59 PM
Yes before i had seeprog ive been using ponyprog hand made and it was reliable. Do it your self job in 20 minutes.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.