Experience with Galletto 1250/1260 Tool!

[grigorean_alexandru]

where could i find galetto maps? is there any dvd iploaded somewhere? Thank you!

[bazare]

all DVD files are crap. trust me those are useless!

[sepistar]

where could i find galetto maps? is there any dvd iploaded somewhere? Thank you!

All these maps are rubbish anyway and if you do not know how to maps, and do not understand how it works better when you let others do the maps.
Regards

[banetv]

where could i find galetto maps? is there any dvd iploaded somewhere? Thank you!
Be very carefuly with maps via internet, and any ohters strange maps. How you know that are good maps? Many ecu's will not receive strange dump. Best solution is if you quality modify your dump and flash it back. Or in any modify dump entry your need ecu identification (immo...). You read first this ECU's propertys.

[tester2010]

Does anyone have the files of "help" folder coming with galletto 1250 software including pictures? mine are *.rtf without pictures...

[egyclick]

Does anyone have the files of "help" folder coming with galletto 1250 software including pictures? mine are *.rtf without pictures...

is there a problem why galletto doesnt read all the way a Sharan 1.9tdi 115hp from 2001?
everytime freezes at 41%

[powerjet]

Hi.
Please, know any explain me what kind of cars really support clone 1260, but in description of product - Galletto 1260 on alibaba or aliexpress is example ,,

AUDI VW BOSCH_EDC16CP34 M58BW0160 R/W A4 3.0 TDI 217 CV
A4 3.0 TDI 4X4 231 CV
A6 2.7 TDI
A6 3.0 TDI 4X4 231 CV
A8 3.0 V6 TDI 215 CV E4
Tuareg 3.0 TDI 217 CV
but in
software example 1260 - new serial.exe you find only models A6 215PS E4........ ???? I have Gall.1260 from China with CD-soft 1260 and have ask - need I different software????? I have cca 3 years Gall. 1250 too and work good....

[easytech]

The other types EDC16 are can-bus Galetto clone is only K-line.

[powerjet]

Not all EDC 16 or EDC 16+ 3.0TDI are CAN, you have bad information...

[powerjet]

I think that 2.7TDI is not CAN too /I think its little older model too time/:D, I have only ask or all Galletto-s V1260 know or knownt communicate/ or have in software/ 2.7TDI and 3.0TDI 231PS or 233PS..... if it any know help me....... thanks

[kikitron]

Hi!

I have some strange behaviors with my clone galletto 1260.
I read my ecu EDC15c7 without a problem. So if i read it again and again i allways get different file. If i read three times i get three different files. Why ?

I can write to ecu without the problem but it takes only 6-7 seconds. Is that ok?
When is reading it takes about 1 minute.

If i write tuned file to ecu and then read ecu after the files are not the same.

http://www.digital-kaos.co.uk/forums/attachments/f173/9173d1262900485-experience-galletto-1250-1260-tool-sm-gal-2.jpg

http://www.digital-kaos.co.uk/forums/attachments/f173/9172d1262900485-experience-galletto-1250-1260-tool-sm-gal-1.jpg

[banetv]

You must read and flash "flash-complete".
If you haven't any problem with car, then all is ok. ECU allways write something in eprom and you "see" this as difference.
Your Galletto is good, I have the same.

[ciy06]

And I bought a clone Galleto until now has not read any of Logan ecu ... what to do in this case ....

[banetv]

Read this post and other http://www.digital-kaos.co.uk/forums/f173/experience-galletto-1250-1260-tool-45024/index3.html#post400863

[jolidj]

hi friend.
hi have the digiflasher 1250,with 3 leed.
whith mpprog i ssave my ept file,erease the digifasher and re write.
but i have the proble,the 3 lead now is all ON.
if you helm me??
the digiflasher not have the eprom inside,have only the ftd232rl and one cip LMxxx.
Digiflasher 1250 is galletto 1250.
help peasssss.

[obnchip]

when you want to buy a galleto that works with Sirius32 just ask for one with pcb without LED and when you receive it, open it and connect inside L-line with K-line with a rezistor... or you can make it directly with a wire but it is safe with a rezistor....
now your Galletto will work on Sirius 32 :P

what size resistor need?

[alfabit]

Not critical, 1K to 10K should be ok, test it, nothing to be broken.

[bambula tuner]

Hello Guys i have a big Problem !!!!

i have read a marelli 5nf s8 with thge Galletto 1260 from a fiat panda without Problems at the first Time. Then i tuned the file and try to reprogramm it then i comes the Error Erase. At the next Try it Programm it up to 100 % but the ecu dont would be closing Errore cicclo CHk and the Car dont Start )o: Shit !!!!!

i also try to programm it with original file. but nothing os work

with kwp 2000 i cant Programm it,


any Idea


Please help me i dont wont order e new ECU

thanks at All

p.s. sorry for my bad English

[alfabit]

Hello Guys i have a big Problem !!!!

i have read a marelli 5nf s8 with thge Galletto 1260 from a fiat panda without Problems at the first Time. Then i tuned the file and try to reprogramm it then i comes the Error Erase. At the next Try it Programm it up to 100 % but the ecu dont would be closing Errore cicclo CHk and the Car dont Start )o: Shit !!!!!

i also try to programm it with original file. but nothing os work

with kwp 2000 i cant Programm it,


any Idea


Please help me i dont wont order e new ECU

thanks at All

p.s. sorry for my bad English

You are in a big sh**, my friend !
Must erase the prom inside the ecu and reprogram with a new clear dump. I am not a Fiat specialist, I work only with Renault, for Reno I could give you a detailed solution, but for Fiat no.
Anyway, that galletto is for the trash can, it is a piece of crap.
Do not let the kids work with that " tool " !

[bazare]

NEVER start flashing a car without a solution in case something goes wrong.

[roadsterrt]

has anyone read modify and flash back an ecu of a smart roadster with a galletto 1260?

[alfabit]

has anyone read modify and flash back an ecu of a smart roadster with a galletto 1260?

Commonly, most of us do not like to play with fire !

[0.33liter]

dacia logan (and Clio 2) petrol use L line for wake-up. Galltetto original have this . Also Byteshooter have the L line (via K - you conect L with K and work with SIRIUS32 and SIEMENS EMS3132 .

[cosmind]

good to know this

[roadsterrt]

Commonly, most of us do not like to play with fire !
I have ordered galleto 1260 and kwp2000+ and i expect to be able to read and write my smarts ecu.
but first i will go to my programmer to save my file so if something goes wrong i can have my data back.
have you got a better solution up to 200$ to propose?

[sosmecano]

I HAVE CABLE AND I NEED GALLETTO SOFTWAR . PLEASE

[bazare]

dacia logan (and Clio 2) petrol use L line for wake-up. Galltetto original have this . Also Byteshooter have the L line (via K - you conect L with K and work with SIRIUS32 and SIEMENS EMS3132 .
clone with no LED can also do this.

[alfabit]

I HAVE CABLE AND I NEED GALLETTO SOFTWAR . PLEASE

Seeking means finding.
Search surroundings, you`ll find.

[se93]

Hi guys

I just got a hold of a Galletto 1260 clone and when i connected the usb cable to my Windows XP SP3 laptop, windows automatically installed the drivers. What procedure do i follow to install the drivers on the CD that came with the Galletto?

In device manager, the galletto shows up as USB serial port Com 10 when i connect the cable to my laptop. I select that and try to update it and locate the folder with the drivers but it says that the wizard could not find a better match for the software.

Also, does the Galletto need to be set to a specific COM port and/or does the com port require any specific settings?

What should be done?

Regards,
Mark

[bts]

thank you galletto 1260 picture

[bazare]

just uninstal your current driver and nstall manually from the cd. galletto doesn't care about port number.

[alfabit]

...have you got a better solution up to 200$ to propose?

Solution for Renault cars :

Yes, you must save your ECU dump with DDT2000, and then you can do anything you want, write tuned maps, anytime you can write back your original map previously saved.
Of course you need a DDT2000 which can Unlock ECU, and this is VERY HARD to find, my friend.

[se93]

just uninstal your current driver and nstall manually from the cd. galletto doesn't care about port number.

I went into device manager, selected the item and deleted it. I went ahead and reinstalled and selected update drivers, but i get the same message saying the wizard could not find a better match. Thus, maybe this will work as is. I will need to see if the galletto reads as configured. I saw on another website, that they connect the Galletto to the vehicle, then to the laptop computer and then windows asks for the drivers. Should it be done like that or would installing it as i did initially (without connecting the Galletto to the vehicle) would render the same installation results?

I just want to be on the really safe side as i want to avoid frying the engine computer.


Regards,
Mark

[alfabit]

I

...I just want to be on the really safe side as i want to avoid frying the engine computer....



With galetto you can`t be 100% sure of that.
Think about, it`s a 15 euro tool, made in china probably, and anything can go wrong, reading, ( especially ) writing ecu, a lot of guys burnt their hands with that tool.
Reading this topic must rise for you lots of question marks. But finally it is your car and it`s up to you to decide.
You can`t fry the ecu, but a bad written map wouldn`t make the engine start.
I am 100% against using such tools .

[se93]

With galetto you can`t be 100% sure of that.
Think about, it`s a 15 euro tool, made in china probably, and anything can go wrong, reading, ( especially ) writing ecu, a lot of guys burnt their hands with that tool.
Reading this topic must rise for you lots of question marks. But finally it is your car and it`s up to you to decide.
You can`t fry the ecu, but a bad written map wouldn`t make the engine start.
I am 100% against using such tools .

What you indicate is very true and i have done lots of reading and heard many things good/bad happening with the use of these clone tools. I am just looking for the precise information on doing the installation correctly and working from there. Lets see what happens.

Thanks for your reply and Happy New Years!

Regards,
Mark

[se93]

Hello to all

I tried reading my ecu with the Galletto 1260 clone and get an impossible to open port message. I went ahead and updated the FTDI drivers with the latest drivers on the FTDI site. Tried reading again and it still cannot open the port. I have disactivated my antivirus/firewall and am using Windows XP Professional.

What else can i try?

Regards,
Mark

[bakewell78]

have you put the updated driver files in to the galletto file and then gone to devices and printers and then updated the driver through properties ?

[se93]

have you put the updated driver files in to the galletto file and then gone to devices and printers and then updated the driver through properties ?

No. So do i have to copy/paste the files into the galletto Drivers_EOBD2_2x_XP folder from the galletto directory? Should i then just erased the original drivers in that folder and then copy the new ones? Do i copy the entire CDM 20808 folder into galletto? Can you elaborate on the second procedure you mention regarding going to devices and printers as i am confused.

Regards,
Mark

[banetv]

Hello to all

I tried reading my ecu with the Galletto 1260 clone and get an impossible to open port message. I went ahead and updated the FTDI drivers with the latest drivers on the FTDI site. Tried reading again and it still cannot open the port. I have disactivated my antivirus/firewall and am using Windows XP Professional.

What else can i try?

Regards,
Mark
You can't change port in Galletto software. Use only software from included CD, they have correct setinngs for THIS galletto. Driver can from ftdi site.

[bakewell78]

i found the cd drivers to be useless and downloaded the latest one from ftdi but in order to make it use the new driver you have to copy/paste in to galletto directory. then start menu-devices and printers(with galletto in usb) right click eobd-properties-advanced settings-drivers-and then update driver-

[bakewell78]

i'm running win 7,but have galletto running in compatability mode on xp service pack 3

[se93]

You can't change port in Galletto software. Use only software from included CD, they have correct setinngs for THIS galletto. Driver can from ftdi site.

I unistalled it again and tried to manually install the drivers from the CD and windows says "The specified location does not contain information about your hardware? And i am 100% sure i selected drive D where i have the CD inserted.

Regards,
Mark

[bakewell78]

have you tried manually installing the updated driver?

[se93]

I have tried to manually install the drivers off of the CD that came with the Galletto, but i get the message that the specified location does not contain information about your hardware. I just installed my external CD/DVD drive and put the cd in there and tried again but i get the same message.

Regards,
Mark

[se93]

Here are two snapshots, one is the file folder of the cd contents and the other is the folder for the drivers on the cd.

Regards,
Mark

[bakewell78]

if you copy/paste the entire CDM 20808 folder into galletto directory as an additional file(not into existing driver file).Then bring up the eobd properties and update driver through this choosing to manually select the file to update from

[se93]

if you copy/paste the entire CDM 20808 folder into galletto directory as an additional file(not into existing driver file).Then bring up the eobd properties and update driver through this choosing to manually select the file to update from

I have also tried that and still the same error. I went back into device manager and tried to update the driver of the Galletto using the CD it came with and windows does not allow it saying what i have posted previously that it cannot find a better match for this device.

I tried it with both firewall/antivirus deactivated and still the same error. On the Galletto itself when i connect it to the round OBD connector, the red light of the Galletto turns on but that is just about it.

The serial to usb adapter i use for the round connector to function with my laptop to access INPA/DIS/SSS is FTDI driver version 1.0.2154.0 dated 4/16/2004 and when i connect the Galletto to my laptop, that is the FTDI drivers its using. Can it be possible that maybe this is causing problems with the Galletto being able to connect?


Regards,
Mark

[se93]

I managed to get it working. It was necessary for me to delete the FTDI drivers i was using for the Serial to usb adapter for the round plug i use for INPA/SSS/DIS. I then went ahead and reconnected the Galletto and it automatically asked for the software disk. I pointed it into the folder i have from the CD software that came with the Galletto and it finished installing.

I went ahead to read the ecu after selecting the vehicle and it read it 100%. File was saved and was able to see it in WinOLS.

It looks good in WinOLS, but just want to be sure. The Galletto software worked flawlessly without any errors and the read time was very fast.

How can i setup Windows XP so that i do not have to be deleting/installing drivers on a constant basis when i use either application, be it Galletto or the BMW diagnostic software (INPA, DIS, SSS)? Remember the FTDI drivers i deleted are used so that my serial to USB adapter works properly as it always has done with those specific FTDI drivers.

Regards,
Mark

[cavignac]

I managed to get it working. It was necessary for me to delete the FTDI drivers i was using for the Serial to usb adapter for the round plug i use for INPA/SSS/DIS. I then went ahead and reconnected the Galletto and it automatically asked for the software disk. I pointed it into the folder i have from the CD software that came with the Galletto and it finished installing.

I went ahead to read the ecu after selecting the vehicle and it read it 100%. File was saved and was able to see it in WinOLS.

It looks good in WinOLS, but just want to be sure. The Galletto software worked flawlessly without any errors and the read time was very fast.

How can i setup Windows XP so that i do not have to be deleting/installing drivers on a constant basis when i use either application, be it Galletto or the BMW diagnostic software (INPA, DIS, SSS)? Remember the FTDI drivers i deleted are used so that my serial to USB adapter works properly as it always has done with those specific FTDI drivers.

Regards,
Mark
hello, I'm in a galley like you, then you like it you explain step by step solution to this problem

thank you

[se93]

hello, I'm in a galley like you, then you like it you explain step by step solution to this problem

thank you

I connected my serial to usb adapter onto my laptop, then went -into system-hardware-device manager and then found the com port where my serial to usb adapter is located and right clicked on it and selected uninstall. Then i went into control panel-add remove software and found the FTDI drivers that were installed for the serial to usb adapter. I went ahead and deleted that too. I restarted the computer and connected the galletto to the computer and immediately i was asked for the drivers. I went ahead and found the location of the galletto drivers and it automatically installed them. I went to the car and was very happy to see that i had perfect communication and the Galletto clone worked flawlessly.

By the way, my laptop uses Windows XP.

Regards,
Mark

[venigo]

Hi, I would like to ask.. Ho do i program my own chk files for galletto? Because it can read and write, I guess that I need winols for this?

Also, I have a Galletto 1260 kit, the chks included at the kit are "pre-tuned" right?


Thanks.

[alfabit]

Hi, I would like to ask.. Ho do i program my own chk files for galletto? Because it can read and write, I guess that I need winols for this?

Also, I have a Galletto 1260 kit, the chks included at the kit are "pre-tuned" right?


Thanks.

Be very careful with that tool, galletto. You must have a back-up solution in case of... problems.
You can resoft your ecu BUT if your engine not start after that, what would you do ?
I personally know a lot of guys crying after resofting with galletto.

I say only that : attention attention, attention ...!

[banetv]

Majority Bosch ECUs you can recivery in case of bad flash. You write original flash back and enjoy. Marrelli ecu is difficult and locked in case of bad flash. Then must flash (withoud OBD) directly inside ecu with BDM or any other programmer. You must have in this case, BDM original flash from your car.

[cavignac]

I connected my serial to usb adapter onto my laptop, then went -into system-hardware-device manager and then found the com port where my serial to usb adapter is located and right clicked on it and selected uninstall. Then i went into control panel-add remove software and found the FTDI drivers that were installed for the serial to usb adapter. I went ahead and deleted that too. I restarted the computer and connected the galletto to the computer and immediately i was asked for the drivers. I went ahead and found the location of the galletto drivers and it automatically installed them. I went to the car and was very happy to see that i had perfect communication and the Galletto clone worked flawlessly.

By the way, my laptop uses Windows XP.

Regards,
Mark
hello se96
I thank you for reply, is very explicit

I'm going to do tonight
thank you

[se93]

hello se96
I thank you for reply, is very explicit

I'm going to do tonight
thank you


Good luck my friend. Took me a while to realize it, but when i did it was able to function without any problems. At least the Galletto was able to read my BMW ecu. When the times comes to write i will see what happens.

Regards,
Mark

[cavignac]

Good luck my friend. Took me a while to realize it, but when i did it was able to function without any problems. At least the Galletto was able to read my BMW ecu. When the times comes to write i will see what happens.

Regards,
Mark
my friend

here is that I have them, without success

Here are the steps: see my computer property and equipment and device manager, see Universal Serial Bus controllers, there are (FT8U2XX)

c is its !!!!!!!!!!!

galletto clone I found no solution

no genius in DK, for aid adjusted the clone

thank you:stickyman:

[se93]

my friend

here is that I have them, without success

Here are the steps: see my computer property and equipment and device manager, see Universal Serial Bus controllers, there are (FT8U2XX)

c is its !!!!!!!!!!!

galletto clone I found no solution

no genius in DK, for aid adjusted the clone

thank you:stickyman:

Do you use any other equipment, cables, serial to usb adapters on the machine that use other FTDI drivers? If you do, then connect it to the computer and look under USB controllers and you will find another hardware selection. I did just that, connected my serial to usb adapter and then went into USB controllers and went ahead and deleted it.

[korabshehu]

Hi to all,
i have a peugeot 406 2.2 hdi, since i have bought this car a have the problem with anti pollution, i changed many parts like air pressure sensor, egr valve, cleaned the fap (manually), but this warning still appear (when i changed the air pressure sensor this warning gone, but after 2 months it come back).
Now i've decided to buy a galletto tool, to disable the fap filter. Can anyone help me in this case and what can i do something else with this tool, can i increase the car performance because i have been tired driving in limp mode.

Thanks

[cosmind]

read file from your car and post it here
we can remove fap for you

[cavignac]

Do you use any other equipment, cables, serial to usb adapters on the machine that use other FTDI drivers? If you do, then connect it to the computer and look under USB controllers and you will find another hardware selection. I did just that, connected my serial to usb adapter and then went into USB controllers and went ahead and deleted it.
thank you for answers
My problem was at calculateures who were (plant)
for his
galletto gives the message (SK1-9) and

KWP2000 gives message (ecu not find)

when I've changed the ecu everything works fine, except the KWP2000 on a (Delphi 1.5 dci) download (flach ecu) has 20% s stopped

give me an explanation, thank you

[cavignac]

hello everyone

delphi 1.5 dci ecu with GALLETTO 1260 CLONE (read ecu) has downloaded a file that size 40k !!!!!!!!!

is normally, I have read by some, there are 3 files of 40k and 256k and 256k original

I seek an explanation while his

thank you

[Morette]

Can anyone identify which lead I have? I have had it for years but never managed to get it to work!

I have read the lead with FT prog and I get
FT 232/245BM
VID- 0403
PID - 6001
Desc. EOBD2
Serial -37269514

eprom contents are -
FTDI EOBD2 37269514

Has a manufacturer made another version locked to the sw they supply?
I have had a look at a few of the serials posted in the early stage of this thread, and they don't match, so is it possible for someone to supply me with a dump that covers a normal 1250 or 1260 (or even new_serial) and I just write this in?

Thanks

edited- lead is marked OBDII in a generic case, no LED.

[marsete]

hello friends, sirius 32, has to put in boot mode to extract the memory map, is made by a bridge with the mass of the quartz crystal to pin 28 of memory.

[alfabit]

Can anyone identify which lead I have? I have had it for years but never managed to get it to work!

I have read the lead with FT prog and I get
FT 232/245BM
VID- 0403
PID - 6001
Desc. EOBD2
Serial -37269514

eprom contents are -
FTDI EOBD2 37269514

Has a manufacturer made another version locked to the sw they supply?
I have had a look at a few of the serials posted in the early stage of this thread, and they don't match, so is it possible for someone to supply me with a dump that covers a normal 1250 or 1260 (or even new_serial) and I just write this in?

Thanks

edited- lead is marked OBDII in a generic case, no LED.

Try one of the subsequent serial no.
47514789
73945110
Program the FT232BL prom with FT_Prog from ftdichip.com
and you `ll see that galletto sw works, but you must try both serials above, one only will work depending on what ver. sw you have.
Must reprogram the serial no. only, not all the fields in that prom.

[Morette]

Thanks, I will try this.
I did think it might need something like that. I have no idea where I even got the cable from, it seems to have always been in my toolbag, so the original soft is long gone!

[Morette]

i have ID from 1050/1080 -> 37269514

Ah!
That was the one I had! I will try my old 1080 lead with new_serial string and the new_serial.exe

Thanks all!


also- is there anyway to understand if the lead works without me trying it in a car now?
On opening the sw, I see "USB DEVICE ACTIVE",
If I change the language, It tells me non active.

If I click read we will see USB DEVICE ACTIVE again, and
"Start data reading...Opening port impossible"

This is normal when unconnected? There is any way to see if the sw is happy?
Thanks again.

[agustinfx]

hello

where can i download galletto 1260 software?

Thanks!

[alfabit]

Ah!
That was the one I had! I will try my old 1080 lead with new_serial string and the new_serial.exe

Thanks all!


also- is there anyway to understand if the lead works without me trying it in a car now?
On opening the sw, I see "USB DEVICE ACTIVE",
If I change the language, It tells me non active.

If I click read we will see USB DEVICE ACTIVE again, and
"Start data reading...Opening port impossible"

This is normal when unconnected? There is any way to see if the sw is happy?
Thanks again.

It doesn`t match the serial no. the cable ( FT232 prom ) and the sw have.
I`ve been in a situation as that , modifing the serial no to match the sw requests will solve that.
You can find what is the sw serial no needs using winhex editor. It will look like this you have a dumpscreen:

If not connected to the car, but working sw+hw, it tries to read, and the software locks itself, and stays this way forever with the hourglass on the screen. No messages.

[Morette]

Thanks again.
I will push on until I get it working OK.

[Morette]

Checked both exe sw and lead sw, matching, reinstalled drivers, and now it tries to read!

Perfect!

[venigo]

Does someone has the original program of galletto (eobd2?)

http://www.galletto-flli.it/IMG_PROGRAMMA/Immagine1.jpg


This one?


Not the cloned versions svp.


Pm Svp.

[korabshehu]

i have a same problem like "Morette" with galletto 1260, with "USB DEVICE ACTIVE" have you solve it? i have bought the galletto 1260 clone, i am trying to read my peugeot 406 2.2 hdi ECU, but i can't, also this message appear "turn 10 sec off and turn on the dashboard wait 10 sec before you continue" what can i do,
help me!

[cezargeorge87]

hello

where can i download galletto 1260 software?

Thanks!

From this forum at page 6.

[alfabit]

i have a same problem like "Morette" with galletto 1260, with "USB DEVICE ACTIVE" have you solve it? i have bought the galletto 1260 clone, i am trying to read my peugeot 406 2.2 hdi ECU, but i can't, also this message appear "turn 10 sec off and turn on the dashboard wait 10 sec before you continue" what can i do,
help me!

Read my posts above, you have all the answers you need there, the same i gave to Morette.
I see he suceeded to make it work, good for him !
:ciao:

[cezargeorge87]

hey m8 here is some pictures from the second galletto tool that i have, and this one can be modified and it can work with sirius 32 ecus.... will attach the pictures here so you can see the differences.
This 2 galletto tools does not work with sirius 32 because it doesn't have the L-line connected which it is used to wake the ecu, and that's why the error that gives galletto it is "Error send wake". If you have any ideea on how to modify it please let me know... thanks!

Hy
can you hellp me please i heave some problems with galletto and kwp 2000 im also from roamania can you give me your tel number?
thanks...

[alfabit]

I succeed finally to make my galletto interface, K+L native lines working ( not tied toghether ! ), but i need a galeto sw with EMS3132 ecu driver, i found only for Sirius 32 ( not the same with EMS3132 ), my galeto reads only the serial no. written on the label of the ecu EMS.
Can someone help me ? A link for a newer galeto sw with EMS driver ?

[alfabit]

Finally I got it !
My home-made galletto works perfect !
I read an EMS 3132, NO ERRORS !
Screendump here :

[btr]

maybe someone had programmed edc16c3.9 my galletto read well but do not programm ecu,open the scanned file as a GM Delco understand, why?:(

[fluorescent]

Hello my problem is:
I buy Galletto 1260 clone is the led one.
First time i use it, was with a Citroen C8 EDC15, it?s read Ok but then when i try it again...i get a problem, is no able to read, to wake the ECU.
I have XP and some VAGCOM programs in it and first time i conect the cable he take the drivers automaticley i thing from VAG drivers.
I update the drivers from original cd but no way to make it works.
I try the original drivers from FTDI web page but the same is not conected to ECU.
I dont want to lose vagcom program.
How i can make it works again?
Is posible to desprograme the cable?
Please help.

[prusony]

HI m8
Tell plz - it is possible to read SIRIU 32 by Galette ??
(I tried EDC15C2 - read well)
TNX

[alfabit]

HI m8
Tell plz - it is possible to read SIRIU 32 by Galette ??
(I tried EDC15C2 - read well)
TNX

As i said above, Siemens Sirius 32 use slow init wake up ( 5 bauds ) needing interface with native K line and L line ( NOT tied toghether !!, even with a resistor )
So you can read EDC15 because it uses fast init - only line K needed in this case - but for ecus on slow init you need an interface with K and L lines ( same case for ddt2000 etc. ) interfaces for waking up slow init ecus .
Look at that screendump i posted above how i read an siemens ems, much the same with sirius 32, the driver is identical.

[prusony]

Thanks for reply !
I use interface with real K & L lines, and K-L-line simply connects together (so without success)
--------------------
and tried to do so:
pin.28 - GND
pin.29 - +12
pin.30 - +12
pin.56 - K
pin.26 - L - without success

[fluorescent]

I think you have to desolde 29f200 and read with some programers like willem.

My Galletto 1260 is dead i think.
I tryed with a citroen c8 first time is read ok but when i tryed again nothig the program is freezing.
Somebody know if i have to do something special to read the ecu with this crap?
I try a new windows and the all drivers that i find and nothing,is recognized by the pc but is not working with the program.
Is a bicolor red one,when i plug it in the car i think the both light is on.
Is based in FTDI232RL and MAX232 he have the k-line conected to pin7 but what i see is the kline go to the led mabe this is the problem with this type of cable.
With my audi a4 2000 also is not working.
I test all the pices inside and all ok i dont know the max232 condition is.
When y install the drivers how i have to see it in the device manager ?
like a usb to serial or FT8UDXXX ?
Thanks all.

[alfabit]

When y install the drivers how i have to see it in the device manager ?
like a usb to serial or FT8UDXXX ?
Thanks all.

You`ll see it two places in device manager, first as USB serial converter and second as USB serial port.
Look i put for you a screendump

[elchip]

I think you have to desolde 29f200 and read with some programers like willem.

My Galletto 1260 is dead i think.
I tryed with a citroen c8 first time is read ok but when i tryed again nothig the program is freezing.
Somebody know if i have to do something special to read the ecu with this crap?
I try a new windows and the all drivers that i find and nothing,is recognized by the pc but is not working with the program.
Is a bicolor red one,when i plug it in the car i think the both light is on.
Is based in FTDI232RL and MAX232 he have the k-line conected to pin7 but what i see is the kline go to the led mabe this is the problem with this type of cable.
With my audi a4 2000 also is not working.
I test all the pices inside and all ok i dont know the max232 condition is.
When y install the drivers how i have to see it in the device manager ?
like a usb to serial or FT8UDXXX ?
Thanks all.

Here is little help ;-)

54289

Many users need to know why ftdi + max232...
So it is simple converter to RS232 level with MAX232 from 5V usb logic. After that they usage simple K-line and L-line with OPamp or transistors.
So it is low cost interface from China ....

Regards

[alfabit]

Here is little help ;-)

Many users need to know why ftdi + max232...
So it is simple converter to RS232 level with MAX232 from 5V usb logic. After that they usage simple K-line and L-line with OPamp or transistors.
So it is low cost interface from China ....

Regards

Why they convert to RS232 the output of FT232 ?
They can obtain K and L lines directly from the output of FT232 with transisitors and/or SI9243 ( my working Galetto home-made does this ), why this conversion to RS232 ?
It is not necessary !
I was curious if you could explain that ?

[elchip]

Why they convert to RS232 the output of FT232 ?
They can obtain K and L lines directly from the output of FT232 with transisitors and/or SI9243 ( my working Galetto home-made does this ), why this conversion to RS232 ?
It is not necessary !
I was curious if you could explain that ?
They do that cos use very simple output stage for K and L line.
But also as you I use L9637D in my Galletto and it work perfect.
I never have any problem and I have L line working too.
So as KWP2000 in past was work with LM339 and now China manufacture use TL072 or 082 for that and that is more bad idea ....
Simple ansvare is look at interface with LM2903 which is direct connected to RS232 so If you usage FTDI + MAX232 you can add LM2903 and have simple hardware on USB for K and L but not good ....
I never understood Chin idea's about low cost electronic solution ... ;-)
And I dont want ...hehehehehe

:hmmmm2:

[fluorescent]

You`ll see it two places in device manager, first as USB serial converter and second as USB serial port.
Look i put for you a screendump

Yes i know that but when i choose the driver from DRIVERS_EOBD2_2K_XP the windows install something like i mentioned FT8U2XX.
The question is wich driver i have to use? FTDI232RL from FTDI web page or the driver from new serial directory?
Is not the same.
Today i make unistalling of galletto driver and download the CMD ftdi setup version from FTDI web page and install it,
when i plug in the cable he get automaticly recognized like EOBD2 USB TO SERIAL PORT in COM5.It?s that corect?
There is a way to test it withou a car?
Finaly i thing that i have to make a homemade cable like kwp2000 with this chinese crap.

[fluorescent]

So if i change the TL072C for a LM339 is much better?
I have one is the same?
I think the problems of this cables is the bad quality pieces to save money and thats why is cost so cheap and work only to give you a headpain.

[alfabit]

Yes i know that but when i choose the driver from DRIVERS_EOBD2_2K_XP the windows install something like i mentioned FT8U2XX.
The question is wich driver i have to use? FTDI232RL from FTDI web page or the driver from new serial directory?
Is not the same.
Today i make unistalling of galletto driver and download the CMD ftdi setup version from FTDI web page and install it,
when i plug in the cable he get automaticly recognized like EOBD2 USB TO SERIAL PORT in COM5.It?s that corect?
There is a way to test it withou a car?
Finaly i thing that i have to make a homemade cable like kwp2000 with this chinese crap.

Use ftdi last drivers 2.08, no those old drivers from galletto sw. Drivers 2.08 are very nice, work like a charm !
I made tests with an ecu in the lab, i don`t know a way to test that interface without an ecu.
And remove all traces of old drivers before installing new ones.

Using TL or LM339 it`s the same, those ic are analog devices, i made mine with SI9243, ic special for communicating on diagnose lines. SI9241 and SI9243 is the best for that, plus transistors for line L.

[betmen]

hello,
it look that I "flashed" my Galletto 1260,or something like that; I was plug it by mistake in the USB slot where I plug in my VCDS, now Galletto don?t work and when it is plugged in, device menager show Ross-Tech HEX-USB in Other Devices,
before this it worked fine,
I install FT Prog, but Galleto is not visible...
anybody know how to fix it?
thanks :top:

[ecutuners]

hello open cable remove 93c46 ( soic 8 ) read file and ill repair the dump thanks

[betmen]

I never did it before, if you can describe procedure with more details?
:top:


hello open cable remove 93c46 ( soic 8 ) read file and ill repair the dump thanks

[ecutuners]

u need am eeprom programmer that support 93c46 8 pin chip u need to desolder it and read the file and i will rebuild the dump for you and you need to program it and then re solder back in, all done

[betmen]

Can?t be done with FT Prog without desoldering?

u need am eeprom programmer that support 93c46 8 pin chip u need to desolder it and read the file and i will rebuild the dump for you and you need to program it and then re solder back in, all done

[ecutuners]

93c46 cannot be programmed in ciruit by ANY device, it must be removed and read / write

[alfabit]

93c46 cannot be programmed in ciruit by ANY device, it must be removed and read / write

Microwire proms are the easiest to program, i do those types with pony serial ( 3R, 3ZD, components less than 1 euro ! ) only incircuit, of course shortening the X-tal of the processor.
Never failed, never burnt proms doing so.
And the dump of memory ( firmware ) for Galletto you can find in the docs with software and schematics, find here on dk.

[betmen]

find where?
what do you mean by "find here on dk" ?


And the dump of memory ( firmware ) for Galletto you can find in the docs with software and schematics, find here on dk.

[alfabit]

Post edited below

[alfabit]

find where?
what do you mean by "find here on dk" ?

Using " search " button will make miracles for you !
I found Galletto schematics and software, firmware here on dk in a post.
I made my Galletto with the know-how found here !
Found three sw ( 1080, 1250, 1260 ) and two schems
Search for " galletto " and you will find it.

[betmen]

It`s easy when you do it before,
with search I get 16 pages of results for galletto,
I will try to find it......
or you can post link
:top:

Using " search " button will make miracles for you !
I found Galletto schematics and software, firmware here on dk in a post.
I made my Galletto with the know-how found here !
Found three sw ( 1080, 1250, 1260 ) and two schems
Search for " galletto " and you will find it.

[alfabit]

It`s easy when you do it before,
with search I get 16 pages of results for galletto,
I will try to find it......
or you can post link
:top:

I send you a link for the sw Galletto 1260, the hw it`s up to you, none of the schems found here worked on slow init ecus, ( K+L lines native ), so i had to draw a schematic by myself which works perfect for slow init ecus, sirius, ems and so on.
If you don`t want to init slow ecus, you can make any schematic you find here on dk. It is no so hard work searching a schematic here, if you know what you are searching !
Here the link for Galetto sw :
galletto - Galletto Version 1260 (http://topstaramb.forumer.ro/t278-galletto-version-1260?highlight=galletto)

[Master01]

đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß...

[alfabit]

Hi

This can work with Sirius32?

Thanks

This is why i must design my own schematics, because all the schematics i found NONE woke up Sirius32 and EMS3132.
So i draw the schematics with lines K+L native ( independent one from each other )
There is an opinion the connecting K to L will wake up slow init ecus, but this is silly idea.
My Galletto work perfect, reads, writes slow ecus. It is not so complicated, a good electonics will solve it in no time.

Exactly like in your photo, FT232RL + Si9243 + a bunch of resistors and transistors ! And it wake up slow ecus ( sirius32 and EMS3132 )
Home-made, no money throw out on scrap electronics made no one knows where !

[bazare]

Connecting L to K line in "NO LED" clone galletto is no silly idea, because it works. You can loose some hours / days to make your own ... or buy from china for 15$. I agree homemade = quality, but china = cheaper and faster.
If you insist I will make some photos and post here + dump read by that clone.

[alfabit]

Connecting L to K line in "NO LED" clone galletto is no silly idea, because it works. You can loose some hours / days to make your own ... or buy from china for 15$. I agree homemade = quality, but china = cheaper and faster.
If you insist I will make some photos and post here + dump read by that clone.

My friend, i tried more than once to wake up slow init ecus by linking K and L, for ddt2000, galletto etc , none woke up ecu.
So i decided to make my own schematics and all works, but K and L independent. I was very angry because a site asked me 150 euros ( !! ) for a Galletto made by them, if only made in China, but made by an electronic guy exactly like me !
And i put here my solenza_orig dump file ( EMS3132 ) read by my Galletto.

[korabshehu]

i have read the ecu with galleto 1260 can anyone help me to remove fap from my file.

Peugeot 406 2.2 hdi 2001
Bosch, EDC15C2

Thank you,

[egyclick]

Hello friends,
I have 2 galletto, 1 is with led and the other one is without led and from what I read it can be used to read sirrius 32 ecu's.

well I opened it but inside it something different from what others like vevepatronu (http://www.digital-kaos.co.uk/forums/members/55741-vevepatronu/) posted: http://www.digital-kaos.co.uk/forums/attachments/f173/11177d1265660447-experience-galletto-1250-1260-tool-1.jpg

mine has 1 wire that bridges pins 7,12,3 which is missing in the photo above, please someone who can say for sure if it's something wrong in my galletto configuration as I didn't test it on any car and I want to be sure it isn't messed up. I attached a picture with it

thank you!

[alfabit]

...something wrong in my galletto configuration as I didn't test it on any car and I want to be sure it isn't messed up...

thank you!

If you want read Sirius, it must have line L conected.
Connexions are : 7 - line K, 15 - line L, 4,5 - GND, 16 +APC.
Without line L you won`t wake up ecu slow init like Sirius 32
So if your ecu doesn`t wake up, you can`t read it , so you have nothing to break your ecu, don`t worry.
Try your Galletto on the car, try to read ecu Sirius, first ecu must wake up, after that you can read it.
If it does not wake up, you can do nothing, ecu protected, can`t be read-write, don`t worry you have nothing to be affraid.
If it does wake up .try to read it. Writing new files iside it it`s an other story !

Later Edit : looking closely to your photo, i see pin 15 ( line L ) not connected so you won`t wake up Sirius. Try it on the car , you obtain nothing useful.

[rsibiza]

If you want read Sirius, it must have line L conected.
Connexions are : 7 - line K, 15 - line L, 4,5 - GND, 16 +APC.
Without line L you won`t wake up ecu slow init like Sirius 32
So if your ecu doesn`t wake up, you can`t read it , so you have nothing to break your ecu, don`t worry.
Try your Galletto on the car, try to read ecu Sirius, first ecu must wake up, after that you can read it.
If it does not wake up, you can do nothing, ecu protected, can`t be read-write, don`t worry you have nothing to be affraid.
If it does wake up .try to read it. Writing new files iside it it`s an other story !

Later Edit : looking closely to your photo, i see pin 15 ( line L ) not connected so you won`t wake up Sirius. Try it on the car , you obtain nothing useful.



Lot of poeple here sometimes also share theyr knowledge.

In change for what would u share your shematic with us?
Mpps dump? VCDS dump?

[Overtune]

Can galletto do siemens sid806 by obd? Or only bootmode?
Someone tested it?

[alfabit]

Can galletto do siemens sid806 by obd? Or only bootmode?
Someone tested it?

In theory, galletto " can do " any ecu, including sid806, IF ONLY you have a driver for that ecu, galletto needs to know what to read and the sectors of flash where the tuning is stored ( begin address, end address, offset )
And that driver must be included in galletto sw, and as i know galletto sw doesn`t accept add-ons, adding new drivers is not permitted.
We must wait for new ver of galletto sw be on the market, with newest ecus included.

[alfabit]

I put there the scematic of galetto K+L working, for all of you interested :

http://www.digital-kaos.co.uk/forums/f173/galetto-k-l-lines-schematic-everything-217651/

[grinovsky]

how about the new galletto1265 some one have test it?
the most important offert is the 2Gb damos add to the new galletto!!!!
Fotos de PROGRAMADOR EOBD2 GALLETTO 1265 + winols1500 +2gb damos + RACE2000 - Quarteira - Pe?as e acess?rios carros (http://quarteira-faro.olx.pt/pictures/programador-eobd2-galletto-1265-winols1500-2gb-damos-race2000-iid-161067318)
http://i43.servimg.com/u/f43/16/03/79/30/gallet10.jpg

[rsibiza]

how about the new galletto1265 some one have test it?
the most important offert is the 2Gb damos add to the new galletto!!!!
Fotos de PROGRAMADOR EOBD2 GALLETTO 1265 + winols1500 +2gb damos + RACE2000 - Quarteira - Pe?as e acess?rios carros (http://quarteira-faro.olx.pt/pictures/programador-eobd2-galletto-1265-winols1500-2gb-damos-race2000-iid-161067318)
http://i43.servimg.com/u/f43/16/03/79/30/gallet10.jpg


Yeah...as these damos cannot be downloadet for free here muahaha...

What is new in 1265...allready spoken about..u can name it as u want..1280..1300...

Is any new protocol been addet..?..supports can?..?

I dont think so...

[grinovsky]

no,i don't see here where i can download 2Go of damos
may be you have a link?
and the new galletto have a new hardware and a new software
so,i think it will give absolutely a new result

[rsibiza]

no,i don't see here where i can download 2Go of damos
may be you have a link?
and the new galletto have a new hardware and a new software
so,i think it will give absolutely a new result

Button SEARCH (in dk) hit winols damos
There is a threat full damos files;) believe me...

I dont wanna believe that new can bus galetto flasher if cracked sold to 75 ? ??? Like crack mpps 350 in start...clone..u get what i mean..

Also they give ecm 6.2 and non working titanium...

But no carlist ..why? U see?

[grinovsky]

ok,clic here to see carliste and new interface
http://i43.servimg.com/u/f43/16/03/79/30/111.jpg

[rsibiza]

ok,clic here to see carliste and new interface
http://i43.servimg.com/u/f43/16/03/79/30/111.jpg


Sorry...for me no link open when i click there:( so for me no carlist..

If u get list,so please to link it;)

[grinovsky]

when you clic where i did show you you will be redirected at
PROGRAMADOR EOBD2 GALLETTO 1265 + winols1500 +2gb damos + RACE2000 - Quarteira - Pe?as e acess?rios carros (http://quarteira-faro.olx.pt/programador-eobd2-galletto-1265-winols1500-2gb-damos-race2000-iid-161067318)
and it's not made in china the new galletto1265
it's made in EU,a perfect copy of original

[lolooo1981]

when you clic where i did show you you will be redirected at
PROGRAMADOR EOBD2 GALLETTO 1265 + winols1500 +2gb damos + RACE2000 - Quarteira - Pe?as e acess?rios carros (http://quarteira-faro.olx.pt/programador-eobd2-galletto-1265-winols1500-2gb-damos-race2000-iid-161067318)
and it's not made in china the new galletto1265
it's made in EU,a perfect copy of original

A new interface of CMD Electronic ?? in their web site no info of this...

They sell interface for a lot of money and this is the first interface i see at lower price...funny...

And this seller is in Bosnia....

Best regards

[lulu2003]

Button SEARCH (in dk) hit winols damos
There is a threat full damos files;) believe me...

but 2gb? ;)
I never found more than 90 MB.

[m1keh]

but 2gb? ;)
I never found more than 90 MB.

It will be 2gb of craply tuned files.

[rsibiza]

A new interface of CMD Electronic ?? in their web site no info of this...

They sell interface for a lot of money and this is the first interface i see at lower price...funny...

And this seller is in Bosnia....

Best regards

This CMD have nothing to do with real CMD never forget this..this site is only clone selling place;)

[rsibiza]

It will be 2gb of craply tuned files.

Ahh...close to reallity...2 gb crappy tune files...possible..

[rsibiza]

when you clic where i did show you you will be redirected at
PROGRAMADOR EOBD2 GALLETTO 1265 + winols1500 +2gb damos + RACE2000 - Quarteira - Pe?as e acess?rios carros (http://quarteira-faro.olx.pt/programador-eobd2-galletto-1265-winols1500-2gb-damos-race2000-iid-161067318)
and it's not made in china the new galletto1265
it's made in EU,a perfect copy of original

Ok..i get no page...

But also not see 2gb damos..only 4gb crappy ori/mod files winols ecm...wingal...etc...

Enought advertising for crappy tool on public forum..

[lolooo1981]

This CMD have nothing to do with real CMD never forget this..this site is only clone selling place;)

I know this.
They sell Mpps Genuine Amt Cartech...clone lol
And they leave in Bosnia/Herzigovina.

[ipejasinovic]

@lolooo1981
What you have against Bosnia? (I saw you mention Bosnia twice in last few posts)

[lolooo1981]

@lolooo1981
What you have against Bosnia? (I saw you mention Bosnia twice in last few posts)

Nothing m8,just for tell it is not in EU,That's all.My mpps V5 was buy at Cmd Electronic.
Just a little things : they have difficulty responding to mail.
No problem with Bosnia.

Best regards

[ipejasinovic]

CMD Electronics Shop is from Serbia. Guys from Bosnia had stock in Germany, but due to some legal problems, not any more. For now.

[lolooo1981]

My mpps was posted of serbia.
In all case, the interface i buy from it work very good no problem,very well assembly,nothing to do with chinese.


Best regards

[ipejasinovic]

Yes, because that guy from Serbia sells MPPS devices from Bosnia ;)

[lolooo1981]

And what difference is this Galletto 1265 and 1260 ?
The software maybe ?

[ipejasinovic]

Nothing. First was actual 1250, but hw was wrong and L line didn't work. So, when new hw was available with working L line, someone clever just edited 1250 sw and change number 50 to 60, later 65 and 70. Now, that device with working L line is sold as new device with "new" software.

[grinovsky]

Nothing. First was actual 1250, but hw was wrong and L line didn't work. So, when new hw was available with working L line, someone clever just edited 1250 sw and change number 50 to 60, later 65 and 70. Now, that device with working L line is sold as new device with "new" software.
is there galletto 1270:eek:?

[lolooo1981]

Ok,i said well i see no difference.The list of car is the same.

Thanks

[zecas]

the version you can change with winhex you can write your own name if you want, but this design of galletto is made by azlina i have it and it is the best flasher i have.

[Overtune]

Every time i try to ID software freezes (only connected to pc)
I thought it was a hw problem, but i bought a new 1260 hw, but then again same freezing of the sreen with new hw.
I tried gal1260 folder drivers, and latest official ftdi, as a next move, but still....any ideas?

[bondiblu]

Every time i try to ID software freezes (only connected to pc)
I thought it was a hw problem, but i bought a new 1260 hw, but then again same freezing of the sreen with new hw.
I tried gal1260 folder drivers, and latest official ftdi, as a next move, but still....any ideas?

I have the same problem. I thought the 1st one was faulty. I got a replacement and it is the same. When I press ECU DATA, I get NOTHING and the App freezes????? It is a BOSCH EDC15P+ tried on 2 different cars, 2 different laptops, different drivers, checked cable serial number etc

I have been through all the pages on this thread :dontknow:

[lolooo1981]

I have the same problem. I thought the 1st one was faulty. I got a replacement and it is the same. When I press ECU DATA, I get NOTHING and the App freezes????? It is a BOSCH EDC15P+ tried on 2 different cars, 2 different laptops, different drivers, checked cable serial number etc

I have been through all the pages on this thread :dontknow:

For Edc15P+ KWP2000+ is the best way for read/write.

Best regards

[alfabit]

Every time i try to ID software freezes (only connected to pc)
I thought it was a hw problem, but i bought a new 1260 hw, but then again same freezing of the sreen with new hw.
I tried gal1260 folder drivers, and latest official ftdi, as a next move, but still....any ideas?

Wait for a message from galletto sw ! Don`t panic ! Sometimes it takes couple tents of seconds for wake up ecu !
Wait for a message . Sw will ALWAYS print a message !
I`ve made many tests with this sw and a hw made by me.
It keeps the hourglass onscreen but always will print a message.
It is not frozen !

[alfabit]

I have the same problem. I thought the 1st one was faulty. I got a replacement and it is the same. When I press ECU DATA, I get NOTHING and the App freezes????? It is a BOSCH EDC15P+ tried on 2 different cars, 2 different laptops, different drivers, checked cable serial number etc

I have been through all the pages on this thread :dontknow:

Same response for you too, above, post #391

[allnamesused]

hi, is edc16u34 skoda octavia work with 1260?,reads ok but not write yet, is there no problem with immo?,thanks.

[rsibiza]

hi, is edc16u34 skoda octavia work with 1260?,reads ok but not write yet, is there no problem with immo?,thanks.

EDC16U34 have no read file...you need MPPS with noread patch:shot:

[allnamesused]

EDC16U34 have no read file...you need MPPS with noread patch:shot:

audi edc16u34 is same no?,reads full flash galletto,however mpps readspartial no?

[busterxxx]

HI,

I have a chinese 1260 clone. It doesn't read my ECU information. It stuck on ECU data process. The same cable flawlessly working on my friend's 9N polo 1.4 pdtdi. He has EDC15p and my polo has EDC15P too. My polo is younger 2005.07. The motor code is BNV.

some data from vcds(My polo):

Address 01: Engine Labels: Redir Fail!
Part No: 045 906 019 CA
Component: 1,4l R3 EDC 0000SG 7537
Coding: 00002
Shop #: WSC 31414

Any ideas?

Thank You,

[lolooo1981]

HI,

I have a chinese 1260 clone. It doesn't read my ECU information. It stuck on ECU data process. The same cable flawlessly working on my friend's 9N polo 1.4 pdtdi. He has EDC15p and my polo has EDC15P too. My polo is younger 2005.07. The motor code is BNV.

some data from vcds(My polo):

Address 01: Engine Labels: Redir Fail!
Part No: 045 906 019 CA
Component: 1,4l R3 EDC 0000SG 7537
Coding: 00002
Shop #: WSC 31414

Any ideas?

Thank You,

Try with kwp2000+, it's the best tool for this.
For me no fail in this ECU.Official or clone NEVER !

Best regards

[bazare]

I read and flashed more than 10 x sirius32 - dacia logan 1.4
Never had problems with my clone galletto.

[kti1970]

Where to buy? I take the interface, saying that Logan is going well?

[busterxxx]

Try with kwp2000+, it's the best tool for this.
For me no fail in this ECU.Official or clone NEVER !

Best regards

I think there is not difference between the cloned and the original hardware. The difference is the usb-serial converter's eeprom content.

So, there is a way to read out my ECU? What is the difference between two identical EDC15P ECUs?

Thank You,

[rsibiza]

I think there is not difference between the cloned and the original hardware. The difference is the usb-serial converter's eeprom content.

So, there is a way to read out my ECU? What is the difference between two identical EDC15P ECUs?

Thank You,

In car,try pull dash fuse...immo may block acces.

Or try on bench...take ecu out of car;)

[lolooo1981]

Fuse n?14 if i remember well...

Best regards

[Overtune]

When i plug the tool in the usb, i open the software, and press ecu id (for example) software freezes, and have to kill it with task manager. I thought it was a drivers problem, so i installed the latest oficial ftdi drivers but still the same thing. I bought 3 new devices, but they all do the same thing. Can someone help me?
Thanks

[alfabit]

When i plug the tool in the usb, i open the software, and press ecu id (for example) software freezes, and have to kill it with task manager. I thought it was a drivers problem, so i installed the latest oficial ftdi drivers but still the same thing. I bought 3 new devices, but they all do the same thing. Can someone help me?
Thanks

I repeat a post by me above :

Wait for a message from galletto sw ! Don`t panic ! Sometimes it takes couple tents of seconds for wake up ecu !
Wait for a message . Sw will ALWAYS print a message !
I`ve made many tests with this sw and a hw made by me.
It keeps the hourglass onscreen but always will print a message.
It is not frozen !

[rsibiza]

When i plug the tool in the usb, i open the software, and press ecu id (for example) software freezes, and have to kill it with task manager. I thought it was a drivers problem, so i installed the latest oficial ftdi drivers but still the same thing. I bought 3 new devices, but they all do the same thing. Can someone help me?
Thanks


I repeat a post by me above :

Wait for a message from galletto sw ! Don`t panic ! Sometimes it takes couple tents of seconds for wake up ecu !
Wait for a message . Sw will ALWAYS print a message !
I`ve made many tests with this sw and a hw made by me.
It keeps the hourglass onscreen but always will print a message.
It is not frozen !

@overtune: did u buy all 3 from same seller?

@alphabit: not all hw is same,if it s faultly it s useless to say it works always...you may build an interface from vagcom kkl to galetto..and this works fine with all it s existing sw..but believe or not,i have seen frozen galetto coz of bad hw.

[alfabit]

..but believe or not,i have seen frozen galetto coz of bad hw.

Ok, i know you have a lot more experience than me working with galetto or other tuning hw, but as long as on the screen you have the hourglass, i learnt to wait a message from galetto sw, and it always did print a message, even waiting for 5-6 mins.
Belive me, i did make lots of galetto hw not working ( my endless tests ) and with hw not work properly, i waited, and waited, and a messege always appeared from sw, even with that wrong galetto hw.
Please do not feel offended, i didn`t intend to, i only expose here my scarce experience with this kind of tools !

[rsibiza]

Ok, i know you have a lot more experience than me working with galetto or other tuning hw, but as long as on the screen you have the hourglass, i learnt to wait a message from galetto sw, and it always did print a message, even waiting for 5-6 mins.
Belive me, i did make lots of galetto hw not working ( my endless tests ) and with hw not work properly, i waited, and waited, and a messege always appeared from sw, even with that wrong galetto hw.
Please do not feel offended, i didn`t intend to, i only expose here my scarce experience with this kind of tools !

I dont feel offendet,dont worry hehe..

I speak from my own experiance..and waiting 3 days for a message is a bit too long.

I dont wanna speak against galetto..it s the most cloned,sold and used interface in the whole world..i startet right with that tool,and wss as lucky as with kwp2000 but had car in list up to 2006-2007 for alfa fiat..

I m still so happy with this tool,that i build mpps to exchange mpps vs my old K L line galetto...

Best regards.

[Mecatech]

hi, anybody have a serial or a mode to use in slave mode?

can be v.1250/60.......

i need test...

thanks in advance

Meca

[rsibiza]

hi, anybody have a serial or a mode to use in slave mode?

can be v.1250/60.......

i need test...

thanks in advance

Meca


U wanna sell locked to slave files to your customers?

[Mecatech]

U wanna sell locked to slave files to your customers?

yes sir...!

Meca

[mislav88]

It doesn`t match the serial no. the cable ( FT232 prom ) and the sw have.
I`ve been in a situation as that , modifing the serial no to match the sw requests will solve that.
You can find what is the sw serial no needs using winhex editor. It will look like this you have a dumpscreen:

If not connected to the car, but working sw+hw, it tries to read, and the software locks itself, and stays this way forever with the hourglass on the screen. No messages.


i'm digging this post as i have the same problem, how can i modify serial no to match one from the sw?

[alfabit]

i'm digging this post as i have the same problem, how can i modify serial no to match one from the sw?

Look here, i explained there how to modify serial no to match sw and hw:

:wink:

http://www.digital-kaos.co.uk/forums/f173/galetto-k-l-lines-schematic-everything-217651/

[azibi130]

why my galletto 1260 clone doesn't read edc15v. it goes to 28% and says change speed error....

[ahadi]

why my galletto 1260 clone doesn't read edc15v. it goes to 28% and says change speed error....

maybe it is usb setting problem , latency should be 1 .

:embarassed:sorry my English is bad

[azibi130]

just found out that the edcu has 2 27c010, only desoldering job

[bts]

Thank you.

[Dakta]

Just out of interest, what is the galletto a clone of?

Is there such thing as an official galletto v1? I've never seen one.

[brooky25]

Hi, Ive tried everything posted in this thread and the 1260 clone I have just hangs as soon as I try read ecu15p. Ive tried windows 7 laptop and windows xp laptop. Program seems to flicker then crash as soon as I try read and hour glass just stays on. Windows recognises Hw and serial numbers are same. Has anyone got any ideas
thanks

[alfabit]

Hi, Ive tried everything posted in this thread and the 1260 clone I have just hangs as soon as I try read ecu15p. Ive tried windows 7 laptop and windows xp laptop. Program seems to flicker then crash as soon as I try read and hour glass just stays on. Windows recognises Hw and serial numbers are same. Has anyone got any ideas
thanks

On some ecus waking up lasts even 90 -100 sec, so look at that hourglass till the galeto sw will print a message. After 5 minutes waiting no message, you must worry.
And sometimes playing with the USB comm port galeto hw is seen is helping.

[brooky25]

Hi, waiting longer than 5 mins, does this mean hw fault. Tried this on 2 vehicles and same

[alfabit]

Hi, waiting longer than 5 mins, does this mean hw fault. Tried this on 2 vehicles and same

Pityfully, this means hw fault. You ( or a friend of yours ) can repair it, me i made mine from zero, schematics posted above.

[mpierola]

found the problem to the silent key errore

corrupt drivers ,but even with the correct drivers for galetto it still didnt work . i did solve it though i installed vagcan 1.4 drivers .

now works like a charm again

Please, can you send to me the drivers.

Thanks

[midnite]

Well here is the one i have but nothing to test it on at the moment. anyone have an idea what the switch is for?

http://i20.photobucket.com/albums/b231/Midnite-Racer/Tools/IMG_0102.jpg

internals all glued up so only a back view.

http://i20.photobucket.com/albums/b231/Midnite-Racer/Tools/IMG_0127.jpg

thanks

[mouaoued]

pilz dump for galletto 1260 FT232RL

[donesko]

anyone tried r/w alfa 156 2.5v6 cf2 m2.1 with galletto?

[Miltiadis]

i aplied the fix to china 1260 interface found here (connect l line to k line via 1kohm resistor) and finaly it worked. ut i get a partial read only. Should i flash back the partial read file moded or i will brick my ecu? I attached the file.

[Miltiadis]

i aplied the fix to china 1260 interface found here (connect l line to k line via 1kohm resistor) and finaly it worked. ut i get a partial read only. Should i flash back the partial read file moded or i will brick my ecu? I attached the file.
So i edited the partial read and flashed back to the ecu. The car runs fine. Thank you for the help.

[aef]

Hello,

i bought this one here out of ebay:
http://www.vista24.biz/ebay/xpicsd/v2cc4524d.jpg

I tried to read a stock VAG me7.5 ecu in bootmode using the 800bb settings. I click ECU ID, following the instructions to shorten pin24, ignition on blabla. Ecu is going into boot mode but then nothing happened and i get ERRORE READID

My bench setup is okay, including switch for ignition, stable 13.8v and so on. I have 2 versions of galletto software here. One with New_Serial.exe and one with eobd2.exe. The serial within exe and cable is identical.

So i think its a driver thing!
Unfortunately i am not able to build a stable setup.
I tried with a notebook and XP. The galletto seams to use the Driver of my 409 KKL blue ebay cable. Then i tried it with a new clean vmware XP and the drivers into the galletto folder.
Also my other box with Win7 64bit didnt work with this software. It uses the 409 KKL driver here too i think.

I will now set up a second clean XP on the notebook and use the drivers delivered with the galletto software.

Are there any recommendations which driver to use?
Would a picture of the inner be helpful?
The newest FTDI 2.08.24 didnt work for me so far.

cheers

[oem]

anyone tried r/w alfa 156 2.5v6 cf2 m2.1 with galletto?

Yes. Without problems. For read you can put flash pin24 to GND. Wrinting directly :)

[Fantomisback]

Hello,

i bought this one here out of ebay:
http://www.vista24.biz/ebay/xpicsd/v2cc4524d.jpg

I tried to read a stock VAG me7.5 ecu in bootmode using the 800bb settings. I click ECU ID, following the instructions to shorten pin24, ignition on blabla. Ecu is going into boot mode but then nothing happened and i get ERRORE READID

My bench setup is okay, including switch for ignition, stable 13.8v and so on. I have 2 versions of galletto software here. One with New_Serial.exe and one with eobd2.exe. The serial within exe and cable is identical.

So i think its a driver thing!
Unfortunately i am not able to build a stable setup.
I tried with a notebook and XP. The galletto seams to use the Driver of my 409 KKL blue ebay cable. Then i tried it with a new clean vmware XP and the drivers into the galletto folder.
Also my other box with Win7 64bit didnt work with this software. It uses the 409 KKL driver here too i think.

I will now set up a second clean XP on the notebook and use the drivers delivered with the galletto software.

Are there any recommendations which driver to use?
Would a picture of the inner be helpful?
The newest FTDI 2.08.24 didnt work for me so far.

cheers


if you can leave your ept file? I think I can help

[aef]

here is my file

thx in advance

[kelekele]

I have same interface like yours and never readed nothing with them :(.
Tried read on bench marelli iaw59f,sagem s2000,some vw and opel cars over obd but nothing.Opened iterface and all components seems ok.Tried on win 7 32bit,but nothing.Serial is correct in soft and in interface.Any sugestion what next???

[kelekele]

My problem solved ;) .
Instead transistor on K-line j3y is diode 5h.Changed this diode with transistor j3y ,and galletto works fine :thrasher:

[DaniXDX]

Original FG Tech 1250 and 1260 software here:

DepositFiles (http://depositfiles.com/files/2tc4qly6b)

[pagautas]

Hi,

I've fixed my with bicolour led by replacing max232.
On the other device I've found ICL7662 burned. Now I'm waiting for parts to arrive.

[FedorovV]

My problem solved ;) .
Instead transistor on K-line j3y is diode 5h.Changed this diode with transistor j3y ,and galletto works fine :thrasher:
What is the diode - 5h? Where to take it or data~~~~ on it.

[michel almeida]

[QUOTE = Givik; 402.422] The same problem.I recently received Galletto 1260, based on FT232RL and with L-Line connected. But can not connect with Logan, giving me "WAKE ERROR SEND" ...
Attached photos (I also tried connecting K and L directly as shown in the photo, but with no result). [/ QUOTE]

Friends I bought one of that model
I do not know if it's clone or not.
Which software can I use?
I tried to read a sirius 32 that one did not read gave an error
What do I need to do to make it work?
I read this whole topic have to make a change for this model to work
But I did not understand how to do it and how to edit the ept file
And how would the boot for sirius 32
Could someone help me please?

[michel almeida]

[QUOTE = Givik; 402.422] The same problem.I recently received Galletto 1260, based on FT232RL and with L-Line connected. But can not connect with Logan, giving me "WAKE ERROR SEND" ...
Attached photos (I also tried connecting K and L directly as shown in the photo, but with no result). [/ QUOTE]

415685415686

Friends I bought one of that model
I do not know if it's clone or not.
Which software can I use?
I tried to read a sirius 32 that one did not read gave an error
What do I need to do to make it work?
I read this whole topic have to make a change for this model to work
But I did not understand how to do it and how to edit the ept file
And how would the boot for sirius 32
Could someone help me please?

[shooting]

[QUOTE = Givik; 402.422] The same problem.I recently received Galletto 1260, based on FT232RL and with L-Line connected. But can not connect with Logan, giving me "WAKE ERROR SEND" ...
Attached photos (I also tried connecting K and L directly as shown in the photo, but with no result). [/ QUOTE]

415685415686

Friends I bought one of that model
I do not know if it's clone or not.
Which software can I use?
I tried to read a sirius 32 that one did not read gave an error
What do I need to do to make it work?
I read this whole topic have to make a change for this model to work
But I did not understand how to do it and how to edit the ept file
And how would the boot for sirius 32
Could someone help me please?

This is just a Clone tool, to read Sirius32 you need a better tool,
or just remove the 29F200 Flash and read with a programmer.
What Renault is your Sirius32 in?

wbr

[michel almeida]

Here in Brazil and clio
2008 1.0 16v

[gfane39]

@DaniXDX you posted to a link where is a file reported after unzipping as a VIRUS...also there are files in russian...did you checked the file?

[gfane39]

Original FG Tech 1250 and 1260 software here:

DepositFiles (http://depositfiles.com/files/2tc4qly6b)

@DaniXDX you posted to a link where is a file reported after unzipping as a VIRUS...also there are files in russian...did you checked the file?