PDA

View Full Version : 2012 Peugeot 508 Continental Bsi pinout please


alimmo
4th December, 2014, 04:48 PM
As the title would suggest, is anyone kind enough to share the pinout with me please
Digamax
4th December, 2014, 09:17 PM
Hi, you dont need pinout, just separate two board of bsi.

Best regards
Vladimir
alimmo
4th December, 2014, 09:43 PM
Hi, you dont need pinout, just separate two board of bsi.

Best regards
Vladimir



Whats the best method or tool to seperate the board as i noticed there are far too many of these pins to pull apart, i am aware of these type of pins (same as old bmw motor held in by same pins) but after giving it a bit too much pressure i thought best to see if i can get a pin out and do it again as hes a regular and not in a hurry.

any help will be much appreciated
barry94
5th December, 2014, 01:51 AM
Use AVDi original work very well !!!
alimmo
5th December, 2014, 02:53 PM
Use AVDi original work very well !!!

I didnt realise AVDI was for "opening" up a bsi !!! anyone else please
michalez
5th December, 2014, 03:07 PM
just cut off top side of connection and then solder back
Digamax
5th December, 2014, 08:11 PM
I use a small pliers or tweezers to collect pins, and then dismantle the two plates.
Try, not so hard.

Best regards
Vladimir
PremierD
5th December, 2014, 08:13 PM
It does not need cut ... you just prize it off of the four connector blocks :)
Merco97
9th February, 2017, 12:37 AM
just cut off top side of connection and then solder back
Good evening I wish to be able to share the file pinout thank you
Good evening I wish to be able to share the file pinout thank you
javyb
9th February, 2017, 11:22 PM
Good evening I wish to be able to share the file pinout thank you
Good evening I wish to be able to share the file pinout thank you
Go ahead then share it

Sent from my SM-G935F using Tapatalk
alkaskad
10th February, 2017, 07:21 AM
That bsi made me to buy smok...aaah the memories....
kelekele
15th September, 2018, 10:59 AM
As the title would suggest, is anyone kind enough to share the pinout with me please

2 pin black connector 2VNR pin 1 and 2 +30(bat) .
60 pin blue connector 60VBE pin 32 +15(ignition).
16 pin grey connector 16VGR pin 16 - gnd
60 pin black connector 60VNR pin 26- gnd
60 pin black connector 60vnr pin 8 -CAN Low
60 pin black connector 60vnr pin 6 -CAN High
Working 100%
Tested today with FVDI on table and fvdi have connection with BSI.I am just connection tested,no mileage changed.I dont believe fvdi 100%...
kelekele
15th September, 2018, 11:02 AM
As the title would suggest, is anyone kind enough to share the pinout with me please

2 pin black connector 2VNR pin 1 and 2 +30(bat) .
60 pin blue connector 60VBE pin 32 +15(ignition).
16 pin grey connector 16VGR pin 16 - gnd
60 pin black connector 60VNR pin 26- gnd
60 pin black connector 60vnr pin 8 -CAN Low
60 pin black connector 60vnr pin 6 -CAN High
Working 100%
Tested today with FVDI on table ,fvdi have connection with BSI and automatic recognize BSI model..I am just connection tested,no mileage changed.I dont believe in fvdi 100%...