PDA

View Full Version : K tag clone problem



darius89
17th December, 2014, 07:12 PM
Hi, I just received clone Ktag, but it dont work. All cars in list grey... not active also not active PROTOCOL button. Tried 2.06 , 2,07 soft, all the same.
Does there problem if it was connected to internet for couple minnutes ???

heteromies
17th December, 2014, 07:41 PM
Hi, I just received clone Ktag, but it dont work. All cars in list grey... not active also not active PROTOCOL button. Tried 2.06 , 2,07 soft, all the same.
Does there problem if it was connected to internet for couple minnutes ???

Click info -button and take photo and send here. There is possible tool is blocked if connected to internet.

prusony
17th December, 2014, 09:28 PM
Read flash inside unit and put here.

darius89
17th December, 2014, 09:52 PM
You mean flash card data ?

bondiblu
17th December, 2014, 09:55 PM
Blocked, should never go online with these clones.

darius89
17th December, 2014, 09:56 PM
does possible to fix ?

bondiblu
17th December, 2014, 11:09 PM
This tool has been blocked online for sure. You can check if the NXP is locked, I'm sure it will be. I think you need to change the chip and re flash firmware.

imcumen
17th December, 2014, 11:16 PM
Yes jlink+new NXP+firmware https://www.youtube.com/watch?v=lN8V2htDNi0

but first check the SD card
I had the same problem I solved
seeks on the DK forum SDcard file for Ktag

Regards

heteromies
18th December, 2014, 08:55 AM
You mean flash card data ?

Not blocked, my opinion. So maybe broblems are in SD card files.

imcumen
19th December, 2014, 04:53 AM
does possible to fix ?

look here for sdcard file for ktag by Zohar
http://www.digital-kaos.co.uk/forums/f173/ktag-clones-most-problem-boot-mode-tricore-can-not-works-repair-solution-here-454360/

korrni
19th December, 2014, 08:35 AM
Hello there, did you manage to solve the problem? Many thanks!!

korrni
19th December, 2014, 10:20 AM
Hello there, I've had the same problem, all options were greyed out and unselectable, but I've managed to write the NXP using J-Link and now it works :), please let me know if you need it! Regards!

darius89
19th December, 2014, 04:33 PM
Rewrited data in card , but didnt help. Please KORRNI Need help with rewriting.

korrni
19th December, 2014, 11:08 PM
Do you have J-link? Tomorrow morning I'll post the flash file, I'm out of the office! Greetings!


Sent from my iPhone using Tapatalk

darius89
20th December, 2014, 09:30 AM
Hi, yes i have j-link but dont have any connecting instructions.
Thanks.

korrni
20th December, 2014, 11:55 AM
http://www.chinaautodiag.com/html/detail.asp?id=377
Download the first link, ktag-j-link-v8-add-tokens.zip (http://www.chinaautodiag.com/download/ktag-j-link-v8-add-tokens.zip)
Use the instructions from the pictures and use KTAG10000-1000-256fff flash file.
Hope it helps!


Sent from my iPhone using Tapatalk

korrni
30th December, 2014, 11:45 AM
Hello there, did you manage to solve the problem? Greetings and Happy New Year to all DK users!

filecloud
30th December, 2014, 02:51 PM
KTAG K-TAG ECU Programming Tool Free Download - ECU Programmer tool - ChinaAutoDiag.com - Free Download Auto Diagnostic OBD2 scanner Software, Driver, Manual (http://www.chinaautodiag.com/html/detail.asp?id=377)
Download the first link, ktag-j-link-v8-add-tokens.zip (http://www.chinaautodiag.com/download/ktag-j-link-v8-add-tokens.zip)
Use the instructions from the pictures and use KTAG10000-1000-256fff flash file.
Hope it helps!
Sent from my iPhone using Tapatalk

:-) Funny to see that these packages are virus infected!

korrni
30th December, 2014, 05:22 PM
It is not my website, as you may imagine, I've just used the *bin file and I've managed to get my crappy ktag an kess clones back on tracks. Strange my antivirus didn't moan anything about.


Sent from my iPhone using Tapatalk

darius89
31st January, 2015, 05:06 PM
Thanks for link and info, my ktag live again.

korrni
31st January, 2015, 05:10 PM
Glad to hear this!! Greetings!


Sent from my iPhone using Tapatalk

heteromies
31st January, 2015, 05:14 PM
When you use chinese soft, please scan your pc, if found any lpk.dll your pc is infected.

xtcund
19th February, 2015, 06:23 PM
Hi all. hope you can help. I am having the same problem. I am trying to follow all these steps but unfortunately, my NXP chip was scratched so i can't the number on it. Even though, i try to write using your tutorial but i get the error "could not find CPU core on JTAG chain" failed to connect.

any suggestion?

korrni
19th February, 2015, 07:13 PM
Please describe your problem, how it did happen, did you try to read/write an ecu while your computer was connected to internet? What firmware did you have, what software did you use, please post a picture of your ktag board. Greetings!

xtcund
19th February, 2015, 08:59 PM
Hi Korrni, I also have Slave original K-tag. I must have connected to the computer that has the original k-tag. It must have done an update… :( i can't really tell what firmware it had. I used 2.07. It was the software that came with the clone. I must have connected to the 2.10 original k-suite and it may have updated the firmware.

Here is my clone's board.

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=300477&stc=1

korrni
20th February, 2015, 12:15 PM
Today I tried, once again, following the instructions given in the video tutorial, to read the NXP processor. Worked from the first time, without any problems. Is your Jlink in working condition? Did you follow the instructions precisely?
Here's a capture while reading:
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=300558&stc=1
If you did everything as you should, then I would try another nxp processor, maybe yours is locked. Greetings!

xtcund
20th February, 2015, 06:28 PM
Hi Korrni, thank you for your help. I don't know if the jlink is in working condition as this is the first time i'm using it. Do you think it can be a comunication problem between the jlink and the ktag board? by the look of it do you think mine has the same chip as yours?
I might have to solder again the contacts because it might be failing to comunicate with the jlink....

thanks again

korrni
20th February, 2015, 08:25 PM
Tommorow morning I'll post a picture of my ktag's board, but, looking to yours, seems quite similar, the nxp's resonator seems different, but this does not make any difference. It would be better to have someone with a reliable JLink, in order to have a starting point in trying to fix your ktag. Your soldered adapter seems ok and it isn't quite tricky to do the job, the soldering points are pretty generous. I personally left the jlink adapter soldered on the board for future possible incoming troubles:) the last mention is to look in your Device Manager and see if your computer recognizes the ktag. Even with all options greyed out, it has to see it in device manager.


Sent from my iPhone using Tapatalk

xtcund
23rd February, 2015, 04:32 PM
Yes, the Ktag is recognized in the device manager. I can't write on the Kess clone so I and really suspicious about a faulty jlink? no green light although it is recognized in the device manager also.

korrni
23rd February, 2015, 08:23 PM
Normally the Jlink's green led should stay lit when it's connected. Find someone with a working one. Greetings!


Sent from my iPhone using Tapatalk

parik
24th February, 2015, 05:33 PM
whre to find firmare v4.03X for china clone kess v2? Thanks.

korrni
25th February, 2015, 08:28 AM
Hello there, there's the 3.099 firmware for Kess V2 Clone, this is the only one I have. Greetings!
301365

xtcund
6th March, 2015, 05:21 PM
Hi Korrni, after buying a new j-link, i finally was able to program the clone. unfortunately now i get the EEFFACE external exception.

simple to solve?

xtcund
6th March, 2015, 07:06 PM
i've programed it again and now it works fine… :)

korrni
6th March, 2015, 08:43 PM
Glad to hear this! Greetings!


Sent from my iPhone using Tapatalk

xtcund
7th March, 2015, 12:13 PM
do you think it is possible to repair this?

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=303157&stc=1

korrni
7th March, 2015, 01:42 PM
You may solder the two broken points directly!


Sent from my iPhone using Tapatalk

immoresearch
9th July, 2016, 01:35 PM
mine does not have SD card.please how do i solve this problem.i mean NXP.IT'S A CLONE

immoresearch
9th July, 2016, 01:40 PM
I JUST OPENED IT NOW AND I FOUND AN SD CARD.PLEASE WHAT SHOULD I DO.

teamtuner
9th July, 2016, 02:09 PM
I JUST OPENED IT NOW AND I FOUND AN SD CARD.PLEASE WHAT SHOULD I DO.
you don"t said what is your problem mate

immoresearch
9th July, 2016, 03:58 PM
PLEASE I NEED SD FILE.I HAVE SAME PROBLEM WITH MY KTAG

immoresearch
9th July, 2016, 03:59 PM
THE ICONS SHOWS GRAY,CAN'T ACCESS CARS OPTION

immoresearch
9th July, 2016, 04:02 PM
please can anyone on here tell me where i can buy a good tool to read ECU'S
I bought a ktag from china recently but has refuse to work
i installed and only the option,settings,help where highlighted blue.Cars,truck and others all grey instead of blue
please what can i do
suggestions are welcome

smirnoff_rules
9th July, 2016, 04:42 PM
please can anyone on here tell me where i can buy a good tool to read ECU'S
I bought a ktag from china recently but has refuse to work
i installed and only the option,settings,help where highlighted blue.Cars,truck and others all grey instead of blue
please what can i do
suggestions are welcomedid you connected to the internet ? if you did its knacked now . need new chip

teamtuner
9th July, 2016, 06:00 PM
please can anyone on here tell me where i can buy a good tool to read ECU'S
I bought a ktag from china recently but has refuse to work
i installed and only the option,settings,help where highlighted blue.Cars,truck and others all grey instead of blue
please what can i do
suggestions are welcome
BEFORE ALL...start ksuite...press info buton and tell me all that is writed there...firmware version...client code...all

Tyson500
15th September, 2016, 07:15 AM
Hi can someone please post file for ktag repair with jlink.

The previous links seems to be have removed.

Thanks

teamtuner
15th September, 2016, 10:12 AM
Hi can someone please post file for ktag repair with jlink.

The previous links seems to be have removed.

Thanks
there are not "repair with j-link" files
j-link you can use it only for fw 5.001 if is not locked with crp
for other fw 6.070,there is not possible to reppair with j-link...but you can reppair with other methods..of corse.outside forum
so,make a screeshoot image with info button pressed when you start ksuite...and post here image

Act Tuning
15th September, 2016, 10:30 AM
The Ktag not damage, it not go online, this problem is related to files and sd cars, can be repair,

Tyson500
15th September, 2016, 11:16 AM
Thanks for the advice. I did manage to fix the problem. It did go online. I got it repaired.

lexuspiotrkow
15th September, 2016, 11:21 AM
I have the same problem today. I run ksuit with connected internet after that on Ktag have gray icons. Kess v2 works ok because I turn off connection.

teamtuner
15th September, 2016, 03:43 PM
I have the same problem today. I run ksuit with connected internet after that on Ktag have gray icons. Kess v2 works ok because I turn off connection.
change new sdcard with one new sdcard 2-4 gb...update with ksuite again

Tyson500
15th September, 2016, 05:29 PM
Kess is still working cause it was not connected via obd when you went online.

Sent from my SM-G900F using Tapatalk

Tyson500
15th September, 2016, 05:30 PM
Ktag you will have to flash nxp to repair.

Sent from my SM-G900F using Tapatalk

teamtuner
15th September, 2016, 08:18 PM
Ktag you will have to flash nxp to repair.

Sent from my SM-G900F using Tapatalk
excuse me..ughuh...how will reflash the nxp if is CRP3 protected?...WTF mate?...do you know what you said?

Tyson500
15th September, 2016, 08:47 PM
Yes mate.. Rewrite data with J link. It works.

Sent from my SM-G900F using Tapatalk

teamtuner
15th September, 2016, 09:03 PM
Yes mate.. Rewrite data with J link. It works.

Sent from my SM-G900F using Tapatalk
if nxp used before firmware 6.070,impossible to conect with j-link or u-link or other tool...IS CRP3 PROTECTED
only if nxp used befor the 5.001 firmware,you can conect with j-link

Tyson500
15th September, 2016, 09:07 PM
OK cool thanks for the info.

Sent from my SM-G900F using Tapatalk

BannedUser
7th October, 2016, 05:30 PM
Im very happy to such helpful people out here. You guys are awesome. Keep it up. I don't have any issues with my ktag yet. But I went through the thread just to read.

If any of you have a beginner guide for ktag, please PM me. I would love to have some basic knowledge before I dig deeper.

Keep up the good work guys. You guys deserve the best. Good luck with everything you do.

teamtuner
7th October, 2016, 05:54 PM
BannedUser from where?

BannedUser
7th October, 2016, 06:11 PM
I did not get banned from anywhere :D Its just a username that popped up from outta nowhere when I register. :D haha..

kospoz
7th October, 2016, 09:03 PM
I am having problem with ktag.i can not read in bootmode.i have tried 3 dif ecus with same results check power supply connection problem.i saw that when i hit read button there is no second light in ktag.i mean the light near the red light which turning on when you plug it with power supply.what is happening here?

ttzag
4th January, 2017, 04:15 PM
I am having problem with ktag.i can not read in bootmode.i have tried 3 dif ecus with same results check power supply connection problem.i saw that when i hit read button there is no second light in ktag.i mean the light near the red light which turning on when you plug it with power supply.what is happening here?

I have the same problem today .
Cant read any ecu ..the blue led light for 2 second then off then 2 second then off ..etc while press button read .
Any one here can help please ??

yolgezer
31st March, 2017, 10:39 AM
Hello,I have a bad internet connection.I need the Jlink program and the current KTAG version.

carmageddon
31st March, 2017, 10:57 AM
@ ttzag (http://www.digital-kaos.co.uk/forums/member.php/181123-ttzag)
and kospoz (http://www.digital-kaos.co.uk/forums/member.php/92593-kospoz)

the problem with this error is simple to solve, change transistor wrong 6C (BC817) with right A6C (MMUN2113LT1G or LT3G)

aandroma
2nd April, 2017, 09:34 PM
Hi Darius89

Did you solve ktag problem??

aandroma
3rd April, 2017, 07:41 PM
Hi darius89 did you solve ktag problem??

Mohmed gubr
10th April, 2017, 03:01 PM
use k tag v 1.89

aqua_life
24th January, 2018, 11:04 PM
Hello,
I have a problem on my K-suite software (first time I am using).
I click on Cars button, then I have options KessV2 and K-TAG.
If I open any car on KessV2 it works ok.
If I open any car on K-TAG all cars are grey and I cannot move from there. I canīt select them. And I would like to read an edc17 with K-Tag.
On info I have the following:
Device type: M
FW version: 4.036
Serial Number: K10033818
Customer code: C7514
Group Code: C7514

I never turned internet on this computer. Only for this software.
Any help to solve this problem ?

Thanks for your help

volter
25th January, 2018, 03:08 AM
KSuite is universal software for the kess and KTag. To have active k-tag's protocols you have plug KTAG device in.

damian475
11th April, 2018, 12:22 PM
Have similar problem kess work ok but ktag dont.
Ksuit recognize but like this
Device type: M
FW version: 4.036
Serial Number: K10033818
Customer code:
Group Code:
Dont show customer and group code. Where is the problem.

hesham10
4th June, 2019, 08:36 PM
I 'm having same problem of Damian 475 ... red Kess 5.017 (2.47) and ktag 7.020 (2.23) eu clone ... Kess installed and working ktag installed and not working (all protocols gray) although installed off-line ... And mentioned by seller that it can work online .. also tried installing each on different laptop .. what should I do? https://m.aliexpress.com/item/32818279123.html?trace=wwwdetail2mobilesitedetail&productId=32818279123&productSubject=Newest-KESS-V5-017-V2-23-KTAG-V7-020-V2-23-No-Tokens-Limit-KESS-5