MAGNETI MARELLI IAW 59F.M3 immo off

[shanker1212]

please help immo off fiat ecu MAGNETI MARELLI IAW 59F.M3
the attached photo shows more details
what chip should i read ? or if there is another way to read the dump without tacking the cover off ?
i will be glad for any help
best regards

[shanker1212]

anybody want to help ?

[jolidj]

you need to read 95160 inside ecu. read in boot mode and post it.

[shanker1212]

jolidj (http://www.digital-kaos.co.uk/forums/members/130237-jolidj/)

thank you for the info but do you think the BDM100 is good for this ECU , or what do you recommend to read and write this ECU
best regards .

[sl4ck]

No mate, there's some story being this ECU's, what HW have you?

I can help you, but you have to be more specific

[jolidj]

you need piasini ore other tool to read eeprom.
ore specific tool for this ecu do it immo off.

[shanker1212]

the ecu is for fiat punto 2005 and has the following written on it :
IAW59f.M3 /HW023 / 3804-ML4
12v 081 01
you can see the photo of this ecu on my first post

[jolidj]

SERCH to read ecu in boot mode, you need tool to read eeprom from ecu.

[rallyarek]

THAT ECU DONT WORK FOR PUNTO 2005 YOU NEED USE IAW5AF.P3

[sl4ck]

You need to buy specific hardware, because your ECU is HW023 (HW < 100), if was HW > 100 you could do it with KWP2000 and modded .dll

Check PM, i tell you were i bought mine, and worked ok, before that i spended many days reading all information and trying another methods, never were able to boot mode with test point.

[shanker1212]

our brother rallyarek (http://www.digital-kaos.co.uk/forums/members/368540-rallyarek/) is right it is not for fiat 2005 it is for 1999
thank you for the correction and i am so sorry it is my mistake .

[shanker1212]

thank you all my friend who participated in solving this issue .
i decided to buy the IAW59 decoder either the Italian one as original or any clone one .
wish me luck .
BR

[jolidj]

best way for immo off of virgin .

[Heleje]

So if i virginize ECU and cut immo line all should be fine ? engine start?

[stefyhgs]

Hello! Old post, but I hope I can find help here! I have marelli edu decoder and I'm trying to make immo off on a IAW 59F.M3 HW 303. the tool makes immo off but the car doesn't start. If i connect the antenna the car starts just fine, but after that the ecu is codded again to the car. So it was no really immo off done, even if the tool says "Vergine, Immo OFF". Is there any wire that needs to be cut before starting the car? If so, witch wire do I need to cut to do the job properly. The car is a 2003 punto with body computer not immobox. Thank you!

[Autronico]

Obviously the tool you are using is not doing its job, if it has done immo off, you do not have to cut or disconnect anything, the car must start.
On your tool, do you have the possibility to make the file virgin and immo off?
Is not that wrong to select?

[stefyhgs]

Yes, I do have the possibility to select vorgin and immo off. There are 3 versions of the software, I tried them all and all do the same job. They tell me taht the ecu is immo off, but the car doesn't start with the key antenna disconnected. If I connect the antenna the car starts fine and aftet that if I do ecu ID again the ecu is codded again. I need immo off bacause the car sometimes has problems reading the transponder. Is there any other way to do immo off on this ecu? I have the possibility to read the eeprom with FVDI.