me7.9.8 + mg7,9,8

[large12390]

hi to all
please i have bdm100 + fgtech all is clone
pleasei try meany time to read st 275 of me 7.9.8 +mg7.9.8 hyundai 1.6 without sacces i need help how can i read its with pine out o that tool
kingregards

[ttzag]

post photo of ecu ( inside)

[2xded]

ECU is based on a 16-bit processor ST10F275.

[large12390]

hi
thanks mr ttzag the photo in attach u can se bouth ecu me + mg and u can see i remove engin cpu from me ecu becuse i tray to read with x prog but when help me i have anther ecu to
and mr 2xded i tray meany time with that photo pinoute without sacces alsow u know thar is anther photo alsow i cant
please if u have pinout u tisted that is good if u help me
regards

[ttzag]

If you need to read it safely and quickly by your fgtech , i can help u but i need a high resolution photo for both ecu , because there is many version from this kind

sent from LG_G2

[2xded]

hi
.............
and mr 2xded i tray meany time with that photo pinoute without sacces ........
regards

Do you unsolder resistor?

[ttzag]

Do you unsolder resistor?
You can read it without desolder resistor

sent from LG_G2

[large12390]

hi
thanks dear her clear photo

[2xded]

You can read it without desolder resistor

sent from LG_G2
Yes, with this two connections (for MG7.9.8).

[large12390]

hi
thanks for u.r help
but how can i read wher is pinout with fgtecg?
regards

[ttzag]

this for car with automatic transmission

connector small 11, 56 = +12v
59 = k line

connector large 1,2,3 = GND

[ttzag]

for car with manual transmission
solder 1k resistor instead fo 100 ohm

[large12390]

hi dear mr ttzag
thank u v mutch
in fact u.r info its new then all i get before and tomorrw will rpelay u resulte
but still 1 think please usay make bridge her ? what u mean is ther 2 bridge from pin 11to 12 and anther 3 to 4 to 5 is this clear
or u mean only from pin 2 to pine11 ?
king regards

[large12390]

dear mr ttzag
ok ok i think naw clear u man like photo of mr 2xded
regards

[ttzag]

Clear your inbox

sent from LG_G2

[large12390]

hi dears
i tray like u told me without sacces
i think i do mistake but i dont know witch that the result in attach
please helpppppppppppppp
regards

[ttzag]

for manual transmission you need two 12+
82= 12+
83= 12+
85= kline
2= ground

and show me photo for fgtech software wich st10f275 you select ?

[datapage]

Rules st10f 100% ok
st10f275 or st10f276
pin processor = 104 to gnd.
pin processor = 105 to 5v.
.
check

http://chiptung.narod.ru/Bosch_MG_7_9_8.html
check this
CHIPTUNER.RU - BSL (BootStrapLoader) ECU Bosch MG7.9.8 (http://chiptuner.ru/content/bsl_mg798/)

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=294026&stc=1

[large12390]

for manual transmission you need two 12+
82= 12+
83= 12+
85= kline
2= ground

and show me photo for fgtech software wich st10f275 you select ?

Hi dear
thanks for u.r alot of help in manult trandmmition yes ido intrnsl gamber from 82to83and auto alsow i did lije photo and about softwere i tray with bouth can and anther
regards

[large12390]

Rules st10f 100% ok
st10f275 or st10f276
pin processor = 104 to gnd.
pin processor = 105 to 5v.
.
check

???????? ??? ??? ???????.???????? Bosch MG 7.9.8 (http://chiptung.narod.ru/Bosch_MG_7_9_8.html)
check this
CHIPTUNER.RU - BSL (BootStrapLoader) ECU Bosch MG7.9.8 (http://chiptuner.ru/content/bsl_mg798/)

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=294026&stc=1
hi
thanks for u.r tray but is this info for fgtech or anther tool?
regards

[datapage]

m8, boot rules for mcu, not for programmers.
when mcu enters boot, use programmer that supports the mcu.
R W

[large12390]

for manual transmission you need two 12+
82= 12+
83= 12+
85= kline
2= ground

and show me photo for fgtech software wich st10f275 you select ?
dear mr ttzag thank u so mutch
all is ok naw
king regards

[large12390]

hi dear mr datapage
thanks for u.r help and i need ask please about link u send to me i see ther is ecu mt38
???????? ??? ??? ???????.??? ??????? ??? Delphi MT20U/MT38 (http://chiptung.narod.ru/Delphi_MT20U_MT38.html)
is this can read alsow by fgtech? or need anther tools
regards

[KFZ]

Hi ttzag
I have the same problem which is , how to connect my Fgaletto or my K-Tag to ecu me7.9.8 + mg7,9,8so will you please help me with photo to find out the pinout please ?
Regards

[sdralas]

hello mr. large12390 , because i face exactly your problem, i cant read bosch me7.9.8 with fgtech , and i have try all the methods reading this ecu, can you share please how you finaly read this ecu..
Thanks in advance