PDA

View Full Version : Ranault 1.5dCI SID301 - which tool to read / write ecu?



WinWoj
23rd January, 2015, 11:54 AM
Hi. I have SID 301 from renault 1.5dci to testing. Which tool is the best for do this ecu?
BR

teerak2uk
23rd January, 2015, 11:58 AM
You want to test or read/write for remapping

betrescudan
23rd January, 2015, 01:29 PM
You want to test or read/write for remapping
:congrats::congrats::congrats::goodpost::roflmao:: roflmao:

WinWoj
24th January, 2015, 10:49 AM
:congrats::congrats::congrats::goodpost::roflmao:: roflmao: Yes, I want to test because I have this ecu for study. If I can read this via BDM100 I want to check my tool. Is it wrong way? I dont understand yours suprices...

sinan33
24th January, 2015, 12:09 PM
You can read/write this ecu from obd by galetto v53 and v54 easily.

WinWoj
25th January, 2015, 10:45 AM
I opened ecu and I found MPC561 mcu and 16MBit flash. BDM pads also present,Could You tell me where is the 1st pin of bdm pads?

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=296399&stc=1

In similar ECU (Sid 206) need to close jumper, here also? Please help me, I haven't galletto yet, I want to use BDM100 to read this ecu.

WinWoj
25th January, 2015, 11:05 AM
I'm not sure I found 2 ground pins (0hm with some '-' of capasitors, but few with '+' caps) and from EVC manuals see above it is pin 1. Could You m8s confirm my point? Regards.

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=296402&stc=1

danielif
25th January, 2015, 12:03 PM
Hi. The best tool for read and write the ECU is http://noimmo.lt/equipment/params/141/
Read/Write EEPROM, Read/Write FLASH, Clear Immo Code, Clear IMPACT DETECTED, Read stored mileage.
Regards.

sinan33
25th January, 2015, 12:22 PM
Don't waste your time with bdm; galletto v53 and v54 tools can read and write it easily.
I have tune many of them.

teerak2uk
25th January, 2015, 12:55 PM
Don't waste your time with bdm; galletto v53 and v54 tools can read and write it easily.
I have tune many of them.
Did it require injector coding after?

WinWoj
25th January, 2015, 03:28 PM
Did it require injector coding after?
I dont think so. If You read map content and modifying only maps or some switches, content of coding didnt change. It depends where IMA located and which memory area modyfing.

sinan33
25th January, 2015, 10:37 PM
You don't need injector coding.

gttuning
25th January, 2015, 10:48 PM
I opened ecu and I found MPC561 mcu and 16MBit flash. BDM pads also present,Could You tell me where is the 1st pin of bdm pads?

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=296399&stc=1

In similar ECU (Sid 206) need to close jumper, here also? Please help me, I haven't galletto yet, I want to use BDM100 to read this ecu.
one think here look in galletto manual,not to worry you wont blow up ecu if you connect wrong bdm points because 12v is connect from main socket.bdm pints have no 12v so if you have no connection just turn around bdm pints and it should be ok.
its impossible to blow up this ecu if you connect 12v and earth right from front socket,12v is not going on PCB