E212 virgin color dash

[dunnnia]

Hi,need help make virgin MB e212 color dash.Eeprom 25128.Real km on dash 2746km.Thanks

[cokolo]

Find someone with Avdi 2 minutes job on OBD only

[vageric]

Hi,need help make virgin MB e212 color dash.Eeprom 25128.Real km on dash 2746km.Thanks

you mean virgin like 0km?

[gepakg]

no matter,if will be 0km will rewrite from ezs real mileage

regards Gepa


you mean virgin like 0km?

[dunnnia]

That dash i want retrofit to car,and need make it virgin.Ori km in ESZ 109056.1.Thanks

[Speedosoft]

I doubt someone's gonna have a "virgin" file for you to match your cluster. Get hold of a DP3, program the mileage to 0 km or a lower value than your EZS and then use the Learn function to learn it to that specific car. It'll take no less a minute.
Or you can do that manually but you need to know the Drive Authorization code (FBS or SSID value) of the recipient car.



Sent from my iPhone using Tapatalk

[dunnnia]

Hi Speedosoft,I try make it witht DP3,but without sucsess.Tool says "unknown version" of the dash.Thanks

[smuggler86]

AVDI can make w204 and w212 dash virgin?

[joemajdalani]

AVDI can make w204 and w212 dash virgin?

You can adapt used dash to EZS with one simple step.

[hass42]

You can adapt used dash to EZS with one simple step.

What if I damaged my dump, retrived another dump from here, write into my dash. My abrites wont read this dash nor eis, they say they're working on this new chip.

[bersch8688]

Test and Report

387584

[hass42]

Test and Report

387584
I already installed a blocker in EIS, would I have to set miles in this dump?


Hass42

[PremierD]

Yes mate ...

[hass42]

OK great, what to do afterwards?
Code it? Adapt? I have das but not online

Also have Abrites original, but I don't think it'll do anything with this vehicle
Hass42

[hass42]

Yes mate ...
Do I need to do anything else after putting miles in it?
Adapt or code? Thanks

Hass42

[volismb]

Do I need to do anything else after putting miles in it?
Adapt or code? Thanks

Hass42

Yes, you must teach it to the EZS

[hass42]

I need to remove blocker to do that, right?

Hass42

[volismb]

I need to remove blocker to do that, right?

Hass42

I don't think you need to remove the blocker. If for some reason the blocker that you are using is blocking the teach-in procedure then you can see the SSID of the EZS and make it the same in the dash

[hass42]

So just put miles in file and hope the EIS will do what it needs to do?

Hass42

[volismb]

So just put miles in file and hope the EIS will do what it needs to do?

Hass42

Well, you have 2 options:
1. read the SSID from the EZS and put it in the dash. Then change the mileage in the dash to 0 and it should work
2. Change the mileage in the dash to 0 and then use Xentry to adapt the dash. In this case you do not need to worry about SSID

[hass42]

Well, you have 2 options:
1. read the SSID from the EZS and put it in the dash. Then change the mileage in the dash to 0 and it should work
2. Change the mileage in the dash to 0 and then use Xentry to adapt the dash. In this case you do not need to worry about SSID

ok I will try to read ssid with abrites, where do I put it into dash though? Abrites wont do anything with reading dash on this vehicle, not through obd anyway.

and if I need to do by das, mine is a 2012 version, offline, you think that'll work?

[lupu_sandu]

Forget about Xentry offline and 0km trick on this car.

[hass42]

Test and Report

387584
OK I put this file in, with miles I needed on first 4 lines and I have no display and mph gauge acts funny.

I doing something wrong?

Hass42

[hass42]

0km didn't work either,

I got dash working with another file from other post in dashboard.

Now I have dashes across where miles is. What is next best step?

Like I said I have DAS offline

Hass42

[volismb]

0km didn't work either,

I got dash working with another file from other post in dashboard.

Now I have dashes across where miles is. What is next best step?

Like I said I have DAS offline

Hass42

The 0 km trick will work with this car for sure.
The dashes mean that the Dash is out of sync with the EZS.
Try to select W204 and in DAS offline check if you can select Developer Data -> Actuators

[hass42]

oK, I need to repair my dump and seems I need SSID to do this.

I had a friend read key and was able to retrive this info from key, anyone can make something out of it?


0E 30 02 F6 8F E0 C8 99 DE C0 CC 3D 03 66 74 0B