DCU3F immo off

[ilen]

Hello,
need me immo off for dcu3f fiat punto 1.9

300898

Thenks....

[klemenm2]

Remove eeprom and try starting


Sent from my iPhone using Tapatalk

[ilen]

does not work ... whether there is someone immo off damp...???

[tqnata83]

write this file
cut pin 20
lift pin 3 and solder to pin 8

[ilen]

I decided the problem using immo tool....
tqnata83 (http://www.digital-kaos.co.uk/forums/member.php/401548-tqnata83), on motherboard pin 7 and pin 8 are short-circuited....
in any case, thank you all for your help....
regards....

[klemenm2]

If eeprom desolder not work connect fuel valve direct to 12v ingnition... This solution works on 1.9 d partner.

Pisi privat poruku ako imas jos koje pitanje[emoji1]


Sent from my iPhone using Tapatalk

[tqnata83]

sorry for inadvertently
lift pin 3 and solder to pin 8

[ilen]

tqnata83 (http://www.digital-kaos.co.uk/forums/member.php/401548-tqnata83), okay is not a problem...

[yukiire.red]

Hi.
Try this.
Pass PM
Regards.

[ilen]

yukiire.red (http://www.digital-kaos.co.uk/forums/member.php/167238-yukiire-red), the problem is solved yesterday....thank you for effort...
you not sent me pass on PM...
regards....

[mancinofranco]

hello ilen file yukiire.red work? give me the password?
thank you.

[ilen]

hello ilen file yukiire.red work? give me the password?
thank you.

yukiire.red (http://www.digital-kaos.co.uk/forums/member.php/167238-yukiire-red), did not send me the password...!!
I finished work successfully with this damp...301312....
regards...

[yukiire.red]

Hello ilen and manchinofranco.
Sorry and I sent path to PM a little while ago.
Best Regards.

[mancinofranco]

thanks ilen this file is immo off?

total immo off?

[DaysGSM]

yukiire.red (http://www.digital-kaos.co.uk/forums/member.php/167238-yukiire-red), did not send me the password...!!
I finished work successfully with this damp...301312....
regards...

Mr Ilen , this is your dump "virgin" , waiting for a good BSI/KEY signal ... So i presume that u have a good Key/transponder , correct ???

[ilen]

thanks ilen this file is immo off?

total immo off?

I'm not sure, I think my damp virgin. I could not test it, the owner of the car was next to me ...
but, damp from yukiire.red, could be immo off total ...
Regards

[ilen]

Mr Ilen , this is your dump "virgin" , waiting for a good BSI/KEY signal ... So i presume that u have a good Key/transponder , correct ???

Mr DaysGSM... (http://www.digital-kaos.co.uk/forums/member.php/234973-DaysGSM) I think you're right....

[mancinofranco]

I need immo off total
thank you

[i_shot_the_sheriff]

Hello friends,

You program that file ,, lift pin 3 and solder to pin 8 and it's immo off?

[mancinofranco]

you can explain it better? i_shot_the_sheriff (http://www.digital-kaos.co.uk/forums/member.php/10708-i_shot_the_sheriff)
http://www.digital-kaos.co.uk/forums/images/styles/DarkCore/statusicon_blue/user-offline.png

thank you

[i_shot_the_sheriff]

I mean..

In order to make immo off in this ecu. DO i have to program the file you give in post #4 and afterwards lift pin 3 of eprom and solder it to pin 8?

[mancinofranco]

not just in the wp status register to 25080?
thanks.

[i_shot_the_sheriff]

I think making write protect with programmer (Willem for example) and lifting pin 3 and shorting to pin 8 is the same..... not sure though..... that's why i ask

[mancinofranco]

if I connect the pin3 to pin8 not block writing.
because the pin8 is + 5volt.
not as its Data Sheet.

who says he has put -mass vss ok.

[mancinofranco]

Friend the file does not work

help tanks

[Cdoc]

HI
THERE IS NO CABLE IN pin 20


write this file
cut pin 20
lift pin 3 and solder to pin 8