need pin code from dump for 1k0920874B dashboard

[bezze]

need pin code from dump for 1k0920874B dashboard. please help
FOUND IT! The PIN CODE IS 28675

[chriskross]

read flash too

[Rito]

need pin code from dump for 1k0920874B dashboard. please help

Must put more info, What car and year, ect !!!!

[bezze]

I bought the 1K0920874B Dashboard from ebay as upgrade to HIGHLINE of MID-LINE 1K0920862K Dashboard in my 2006 JETTA TDI. I managed to get the PIN of my existing 1K0920862K Dashboard as well as IMMO PIN, but unable to do anything with new Dashboard.

[bezze]

Also I don't have any serious programmer to read FLASH. I managed to read the 24LC32a eeprom content using WILLEM PROG...

[bezze]

read flash too

I bought the 1K0920874B Dashboard from ebay as upgrade to HIGHLINE of MID-LINE 1K0920862K Dashboard in my 2006 JETTA TDI. I managed to get the PIN of my existing 1K0920862K Dashboard as well as IMMO PIN, but unable to do anything with new Dashboard.
Also I don't have any serious programmer to read FLASH. I managed to read the 24LC32a eeprom content using WILLEM PROG...

[bezze]

I bought the 1K0920874B Dashboard from ebay as upgrade to HIGHLINE of MID-LINE 1K0920862K Dashboard in my 2006 JETTA TDI. I managed to get the PIN of my existing 1K0920862K Dashboard as well as IMMO PIN, but unable to do anything with new Dashboard.
Also I don't have any serious programmer to read FLASH. I managed to read the 24LC32a eeprom content using WILLEM PROG...

[vlado kljucar]

In case of CDC3272 do not read Micronas. Select and read only 24C32.

For Micronas CDC3217 & CDC3297 for flash reading use XProgM (24c32 and flash)

[bezze]

OK, so without FLASH there is no way of reading the Dashboard PIN from the dump I uploaded earlier?

[chriskross]

no this dash has 3217 micr. there is the encrytion key for decoding data in eeprom.

[bezze]

I am a bit confused now. I already uploaded my eeprom 24lc32 dump. Do I still need to read the new Dash with xprog-m as vlado kljucar described above?

[chriskross]

yes you must read, but if you not have good soldering skills you can easy damage cluster

[yugo45]

OK, so without FLASH there is no way of reading the Dashboard PIN from the dump I uploaded earlier?
To get Pin you have to read Flash + eeprom, Eeprom is encrypted and it can be decrypt only with Flash.
But with just Pin you will not be able to do anything.

[bezze]

Sure. The point is to get the PIN and add the dashboard using vcds. If that is what you had in mind...

[yugo45]

Sure. The point is to get the PIN and add the dashboard using vcds. If that is what you had in mind...

No,Not possible, you can not do that. VCDS does not support adaptation on this cluster .

[bezze]

Need help with instrument cluster swap as written previously.
Old Cluster - 1K0920862K - I have its PIN
New Cluster - 1K0920874B - I have its PIN
The problem is when I install the new cluster I cannot perform adaptation with VCDS as per Ross-Tech instruction - http://wiki.ross-tech.com/wiki/index.php/Immobilizer_IV_Immobilizer_Swapping_(Instrument_Cl uster
- When I do 25 - Immobilizer -> Security Access - 16 -> use the PIN of the NEW instrument cluster -> Code Accepted
- Adaptation - 10 -> Enter 050 in "Channel Number" -> Read -> Error! cannot read because of communication error!
Waited with new cluster installed more than an hour, unfortunately no change...
Any help would be gratly appreciated

[firestator]

Need help with instrument cluster swap as written previously.
Old Cluster - 1K0920862K - I have its PIN
New Cluster - 1K0920874B - I have its PIN
The problem is when I install the new cluster I cannot perform adaptation with VCDS as per Ross-Tech instruction - http://wiki.ross-tech.com/wiki/index.php/Immobilizer_IV_Immobilizer_Swapping_(Instrument_Cl uster
- When I do 25 - Immobilizer -> Security Access - 16 -> use the PIN of the NEW instrument cluster -> Code Accepted
- Adaptation - 10 -> Enter 050 in "Channel Number" -> Read -> Error! cannot read because of communication error!
Waited with new cluster installed more than an hour, unfortunately no change...
Any help would be gratly appreciatedthe correct answer in the post number 15 !!! Listen! you have helped, just be aware of it)

[bezze]

So if VCDS cannot do it, what tool can?

[lupu_sandu]

AVDI, Smok Xcan, even manually with xprogM