PDA

View Full Version : rcd 210 panasonic


nigrou
12th March, 2015, 11:08 AM
salam
plz help code and safe2 rcd 210 panasonic
serier:014vwz5z1h00300787
1k0 035 156 a
I know very well that is not code in the eprom
But Sally programmed to read m32c
Is there another solution device
Thank you
audiopoint
12th March, 2015, 11:58 AM
http://www.digital-kaos.co.uk/forums/showthread.php/318365-RCD500-MP3-CODE?p=2143473&viewfull=1#post2143473
try solution without code for RCD500 maybe work on rcd210
nigrou
12th March, 2015, 12:07 PM
[QUOTE=audiopoint;2490574] http://www.digital-kaos.co.uk/forums/showthread.php/318365-RCD500-MP3-CODE?p=2143473&viewfull=1#post2143473
try code sans solution verser RCD500 Fonctionne Peut-etre sur rcd210 [/ QUOTE] Ce lien ne fonctionne pas, il se ouvre une page avec l'erreur 404 o

posible reset couter
nigrou
14th March, 2015, 10:05 AM
solved code 0025
I find the method to decode rcd210 panasonic
was ready two days
mlulic
5th May, 2015, 10:22 PM
with which programer you read mcu
iProg-carradio
6th May, 2015, 03:16 PM
with which programer you read mcu

code in MCU
MCU = M30879FKAJP
programmer = M16C Flasher
skens
3rd September, 2015, 12:15 PM
hi

i downlaod M16C flasher!
how to connect to the serial port on the MCU?
of which position is hidden cod?
regards
kappa1
3rd September, 2015, 12:18 PM
hi

i downlaod M16C flasher!
how to connect to the serial port on the MCU?
of which position is hidden cod?
regards

Try this conection: http://help.martech.pl/?q=node/41
skens
3rd September, 2015, 03:50 PM
hi

M16C flasher
connect to the direct serial port DB9 or DB25 LTP on the MCU!
not need interface?

regards
attilaa0
3rd September, 2015, 06:01 PM
You need interface of course.In picture is the martech adaptor DB25 not direct LTP port.This adaptor conect to the martech box.And martech read this m32c.
Also i tried with rs232 interface but not conect to this M32c, only conect to RCD500 m32c flash.Maybe somebody has a solution.
Also have solution to loked the counter but in this way takes more time to find code.
skens
4th September, 2015, 01:22 PM
hi

ihttp://www.m16c-flasher.de/
please read
There is no extra hardware required. The only thing you need is a serial cable between pc and microcontroller...
regards
attilaa0
4th September, 2015, 06:55 PM
Yes !You are right but it can read only M30833 from rcd500 panasonic.For rcd210 you must read M30879 which can not support this flasher.
tintin2005
20th July, 2017, 03:32 PM
You need interface of course.In picture is the martech adaptor DB25 not direct LTP port.This adaptor conect to the martech box.And martech read this m32c.
Also i tried with rs232 interface but not conect to this M32c, only conect to RCD500 m32c flash.Maybe somebody has a solution.
Also have solution to loked the counter but in this way takes more time to find code.


Hello man.

Help please!

Can you share the conections you used to read m30833 from rcd500 mp3?

regards
sonices
20th July, 2017, 05:45 PM
These are connections
tintin2005
20th July, 2017, 05:56 PM
Hello.

Thanks for aswering.
Acording to the picture attached how should be the correspondent connections made?

regards
sonices
20th July, 2017, 06:08 PM
You have it on picture all

CNVSS to Vcc is important

It can read only M30833 but not M30879, as attilaa0 (http://www.digital-kaos.co.uk/forums/member.php/76791-attilaa0) said
tintin2005
20th July, 2017, 11:00 PM
Hello Man.

Thanks for comment. I need to read m30833 from rcd500 mp3...
i tested lots of different ways to comunicate but all unsuccesseful.
Attached are some info that i have been reading, especially in renesas and some foruns.
I changed the max232, reviewed all the interface adapter, changed operating system from xp to w98 but still not getting comunication...

i am about to give up..... Help ...

Edit: should i dessolder mcu from board and then try to read it?


regards
sonices
21st July, 2017, 07:59 AM
Dont give up so easy :itsme:
tintin2005
21st July, 2017, 10:57 AM
Hello sonices!

Uau Man! You did it....! i have not seen the flasher version you have...

Share connections please. if possible a picture.

thank you
sonices
21st July, 2017, 11:33 AM
http://www.m16c-flasher.de/
tintin2005
22nd July, 2017, 04:52 PM
Hello.

As i did not gave up... here i am.... thank you for your help.

Attached is the Dump from m30833 finnaly....

Code please....

regards
tintin2005
Decode Ghost
22nd July, 2017, 04:55 PM
Hello.

As i did not gave up... here i am.... thank you for your help.

Attached is the Dump from m30833 finnaly....

Code please....

regards
tintin2005


Try..............0070
sonices
22nd July, 2017, 05:04 PM
tintin2005 nice to hear it works :dancing:
tintin2005
22nd July, 2017, 05:35 PM
Hi!

Code works.... big thanks.

For me wasn?t enought the "text" schematic from http://www.m16c-flasher.de/ .

regards
carradio2001
31st July, 2017, 03:45 PM
Hi !
What about ID ? I get this message after Connect, when try to READ

Carradio2001.
sonices
31st July, 2017, 05:20 PM
What cpu you are trying to read?
sk760
7th October, 2019, 01:23 PM
Hi !
What about ID ? I get this message after Connect, when try to READ

Carradio2001.

I have same error ,MCU is Renesas M30879
XJTAG
13th December, 2019, 03:07 AM
I have same error ,MCU is Renesas M30879


i have same error, with RCD210 MCU M32M30879 , the mcu is protected


The microcontroller is protected by a 7 byte ID. Without the correct ID, it is not possible to read,
write or erase the flash memory.


The NON-PROFIT version of the M16C-Flasher only writes the ID 0x00 0x00 0x00 0x00 0x00
0x00 0x00, so there is no protection.


You have also the option to log all used IDs into a file (ID.LOG)


By default the M16C-Flasher uses the last working ID. This is useful under most conditions.
But if you are working at different devices with different IDs, you should select 'Extract ID from
File