Ssang yong Rexton 2.7 2009

[luis12]

Hello friends, this car has broken immobox then better solution is immooff, I tryed some dumps of f?rum but sarts once time and locks again... attached dump. Are any other immomodule apart of immobox in key cilinder? Atached dump, thanks in advance.

[MVVL]

Hello. Disconnect the connector from the amplifier IMMO (ignition on). IMMO lamp should go out. Password in PM.305151

[luis12]

Thank you but no messages in PM from you.

[Lexas]

here your immo off. no password! first disconnect immo box, then plug in ecu. check PM for aditonal information.

[mancinofranco]

thanks friends

[Lexas]

thanks friends

downloads: 620... still got some free space in your hdd? :D

[luis12]

Car dont start, immo malfuntion code P1631 Inmobilizer error (not active) light on cluster are ON but immobox ar disconected, are any other immo module? Attached dump that dont start, thanks Lexas.

[elephantul]

are you sure if immobox is disconected ? maine disconect another module

[luis12]

I dont see any other immobox only key cilinder antenna/module... are any other ?

[MVVL]

luis12 tried my dump?

[luis12]

Let me try friend car is not with me.

[Lexas]

confused. usually this solution tested and worked. Make in dump line 04C0 all FF FF FF FF.... and try to start

[luis12]

I made some experiments, if use Immooff with all the variants always immolight are on and gives code, no start, suppose there are a Cheksum conflict, reload original dump and light are now blinking, made recoding module with Gscan2, need to set inmobilizer to NO, some time wasted trying to put values that be accepted, finally put 2005/2/2 and acepted coding, reseted ignition and now immolight is off, no codes and start and accelerates. Well now has code for heaters but starts OK, Hope this solves future problems for others, easy solution with no dissasembly anything, Thanks to all specially for friend Lexas....

[auto4]

I made some experiments, if use Immooff with all the variants always immolight are on and gives code, no start, suppose there are a Cheksum conflict, reload original dump and light are now blinking, made recoding module with Gscan2, need to set inmobilizer to NO, some time wasted trying to put values that be accepted, finally put 2005/2/2 and acepted coding, reseted ignition and now immolight is off, no codes and start and accelerates. Well now has code for heaters but starts OK, Hope this solves future problems for others, easy solution with no dissasembly anything, Thanks to all specially for friend Lexas....

Hi, Please could you tell me where do you put 2005/2/2 values?
Thanks

[luis12]

Go to Special funtion... Recode... Engine 2.7... in inmobilizer option change Yes for No, it will appear a small window asking for year, month and day.. Put 05/2/2 then enter if code accepts, cicle ignition for 15 sec. then ON again, immolight must be off now. No code of Immo and car starts. Hope will be usefull.

[auto4]

Go to Special funtion... Recode... Engine 2.7... in inmobilizer option change Yes for No, it will appear a small window asking for year, month and day.. Put 05/2/2 then enter if code accepts, cicle ignition for 15 sec. then ON again, immolight must be off now. No code of Immo and car starts. Hope will be usefull.


I solved doing immo off in eep 95320.
Thank you very much anyway.

[mancinofranco]

thanks auto4 we walk the file immo off 95320?

[Lexas]

thanks auto4 we walk the file immo off 95320?

Downloads638
Still got some space in your HDD? :D