PDA

View Full Version : Sirius32 boot mode read with galetto v54



Fec001
19th March, 2015, 03:50 PM
Hi!
I want to read this ecu by boot mode but found nothing about it in fgtech documents. Can someone share pinout and bootpin of ecu?http://tapatalk.imageshack.com/v2/15/03/19/6ba7ebd72a495e33814e7ebfcddeb684.jpg

Vasily.U
19th March, 2015, 05:12 PM
Boot 28 pin 29f200

Fec001
19th March, 2015, 08:29 PM
Always get error:
error BOOT SET10
error ADDR_READ.
Tried to lift pin 44 and give +5v via 1k resistor but nothing............. If not put boot pin to gnd, just simple error Boot mode inactive :/

PartyTwist
19th March, 2015, 09:32 PM
I recently played with this too - There's an "official" picture in FGTech folder, but it doesen't work any way I tried. I would guess that v54 galettos have some problem with l-line. I had some info (but can't find it now) how to test kl-lines but I never got around to do that - didn't have time and took the chip off. Hopefully someone will shed some light as this would be very nice to know.

P.S: If you follow the docs (pin 28 via 1k ohm to GND) and select Delphi DDCR it's doing something, and you get a file, but it was totaly wrong from what I saw.

Good luck!

Fec001
19th March, 2015, 09:33 PM
Yes I read as delphy DDCR and file is seems ok to me

smt
19th March, 2015, 09:39 PM
the right boot mode with fgtech for sirus 32 is: pin28 to 1khom to the the boot wire(not to gnd) ,tested many time ;)

Fec001
19th March, 2015, 10:15 PM
You mean this boot pin to flash pin 28?

Artilect
19th March, 2015, 10:31 PM
FGT2 work good with Sirius 32N only and Will not work on Sirius 32. Simply as that and tested many times. If you do not have 32N ecu do not bother to try it have diferent boot loader and have to be soldered.

Fec001
20th March, 2015, 08:08 AM
Dump whatI read seems ok in winols and ECM titanium. I think it must be good. Any other checked that?

pepi
20th March, 2015, 08:29 AM
The best way to check is double reading with fgt2 and flash programmer then you can compare dumps.

Fec001
20th March, 2015, 08:44 AM
the right boot mode with fgtech for sirus 32 is: pin28 to 1khom to the the boot wire(not to gnd) ,tested many time ;)
Tried yout method but got Boot mode inactive error

Meat-Head
20th March, 2015, 08:47 AM
Many years ago dk member adam28 tried this try stalking

crisgsm
20th March, 2015, 09:28 AM
Hi!
can someone, please, share exact conection with galletto?
i saw one picture where green and blue wire is k and l line, but green have 12v
please share exact conection

Thank you!

Fec001
20th March, 2015, 09:35 AM
Great! Tried to write immo off file back as delphy DDCR boot mode and it fails at 9% :D

autocargo
20th March, 2015, 09:46 AM
Sirius 32N would work read/write but sirius32 never worked for me... According to some people there's another way to put sirius32 in boot mode, I desolder flash memory on this one. When I'll have some spare time I will try experimenting.

crisgsm
20th March, 2015, 09:58 AM
Please share conection!
i have time to test!

Thank you!

Fec001
20th March, 2015, 11:10 AM
Please share conection!
i have time to test!

Thank you!

Here you go!

crisgsm
20th March, 2015, 11:54 AM
Here you go!

Thank you!
But as i said, green line have 12v on it!
are you sure is L line is green? On my galletto i have 2 wiers green!

Fec001
20th March, 2015, 12:00 PM
forget it, boot cable is only for tricore ECUs(as I know). wire ecu through an OBD plug to the galetto obd plug

EDIT:

I tried, K-line is the green wires

morgano
20th March, 2015, 04:45 PM
Yellow wire of the boot cable is L-Line ;)

smt
20th March, 2015, 05:44 PM
ok,i wil give the exact procedure:

--connect wires like fgtech sirus 32 pinout exept boot
--supply 13v to fgtech
--turn fgtech cable ignition switch to ON
--on fgtech menu select driver--->tool boot --->tool boot mode-->siemens infineon c167--->sirus 32 boot mode
--click connect
--wait until fgtech show the boot procedure message
--turn fgtech cable ignition switch to OFF
--connect grey wire(boot wire) with 1khom resistor to 29f200 pin 28
--turn fgtech cable ignition switch to ON,
--disconect grey wire then click OK

now fgtech can connect to the ecu
same procedure when reading & writing
100000000000000000000000000000000% working
gooooooooooooooooooooooooooooooodLuck

Fec001
20th March, 2015, 06:36 PM
I did the same but always get error boot set10

Fec001
20th March, 2015, 06:39 PM
If do something wrong about boot procedure, I got error boot mode inactive

houcem80
20th March, 2015, 09:13 PM
i test but i have error

PierreTheron
20th March, 2015, 09:18 PM
Many years ago member adam also tried it ..
So why now when we have good programmers we need to go along this line again ...................
Just read and reprog it by a programmer m8's

Vasily.U
20th March, 2015, 09:43 PM
Russian program chiploader read sirius32 in boot mode without problem with kl-adapter but sometimes file just trash
depends on the last letters of the processor.

mancinofranco
21st March, 2015, 05:01 PM
Program chiploader Russian sirius32n read in boot mode without problems
with mpc infineon with mpc siemens does not work

AutoElectronicaFS
21st March, 2015, 07:45 PM
I will read Sirius32N with 29f200bb in v54 without any problem.

305678

autocargo
21st March, 2015, 09:11 PM
I will read Sirius32N with 29f200bb in v54 without any problem.

305678

There's no need for L line (yellow cable) to read sirius 32n in boot mode...

mancinofranco
22nd March, 2015, 12:05 PM
ok AutoElectronicaFS (http://www.digital-kaos.co.uk/forums/member.php/416125-AutoElectronicaFS) program chiploader Russian sirius32n read in boot mode without problems with mpc infineon.
with mpc siemens does not work.

Fec001
23rd March, 2015, 09:01 AM
I'will order another external programmer because GQ-4X is a piece of shit. Can't read(always verify error) and write 29F200BB and many problems with the others too (29Fxxxx,28Fxxx). My local programmer dealer has Wellon VP 596. Is that a reliable tool? I ask because GQ-4X caused me a lots of headache in the past........