PDA

View Full Version : COBRA1423 IMAGE VER:00.5 IS RELEASED NEW NEW NEW!!!!!



cobra1423
20th March, 2015, 12:31 PM
HI EVERYONE OK NEW IMAGE V.005 IS OUT REMEMBER AND READ THE GUIDE SO HERE WE GO ITS IN THE DOWNLOADS AREA ENJOY
COBRA1423 IMAGE DOWNLOAD HERE--------> ................................................

ps. I have tried it on sim2.0.1 BUT NOT sim2.10 please let me know if it installs ok.:chuncky:

miau18
22nd March, 2015, 01:44 AM
it works!!but takes lots of time booting when we restart the enigma!!!

cobra1423
22nd March, 2015, 03:28 PM
it works!!but takes lots of time booting when we restart the enigma!!!
Hi it's set to check the epg that's why it takes a bit longer you can switch it off by going into crossepg configure settinngs and select force epg reload on boot and set it to no. That will make it boot faster hope that helps you out.
Cheers cobra1423

miau18
24th March, 2015, 12:10 PM
hi cobra its possible to get zap mode in black screen?when change channel it keeps picture in last channel?thanks

dannyboy
26th March, 2015, 11:52 AM
Mate I flashed my dreambox with it but I had to flssh it back as it wouldent boot and kept loading the bootloader then stop then flash again
My box always was a lazy starter
Ive got another dreambox 800 with a ferrari sim is it just a matter of taken the sim card out and changing it and then flash it again
I think my board is on its way out
Thanks in advance daniel

cobra1423
27th March, 2015, 01:24 AM
Mate I flashed my dreambox with it but I had to flssh it back as it wouldent boot and kept loading the bootloader then stop then flash again
My box always was a lazy starter
Ive got another dreambox 800 with a ferrari sim is it just a matter of taken the sim card out and changing it and then flash it again
I think my board is on its way out
Thanks in advance daniel
hi it's for sim2.0.1 &2.10 yes you can change your sim
Cobra1423

dannyboy
27th March, 2015, 02:47 PM
Is it simple to do and does it usualy take ages for the image to boot up ? Cheers daniel

MW35
27th March, 2015, 05:10 PM
where can i find the image? thanks

cobra1423
29th March, 2015, 10:40 PM
[QUOTE=MW35;2500036]where can i find the image? thanks[
COBRA1423 IMAGE DOWNLOAD HERE------> http://1drv.ms/1vtnxus

digicon
30th March, 2015, 12:46 PM
The Image can be Downloaded from here:
https://onedrive.live.com/?cid=48e1ab905262688d&id=48E1AB905262688D%21109


Please do not post links to other forums with a similar content, it takes a minute or two to actually upload to a file sharing site that everyone can use

Thank you

tidsfm
2nd April, 2015, 08:51 PM
I can not get this image to install.
I'm using sim 2.0.1 and tried to install via browser
I have the correct bootloader
It just hangs with the earth picture and flashing red light on dreambox.
Waited about 20 mins and still the same
If i try version 00.4b it works perfect.
Am i missing something or any tips to try, Is it worth trying usb install

andiewill
2nd April, 2015, 09:59 PM
I can not get this image to install.
I'm using sim 2.0.1 and tried to install via browser
I have the correct bootloader
It just hangs with the earth picture and flashing red light on dreambox.
Waited about 20 mins and still the same
If i try version 00.4b it works perfect.
Am i missing something or any tips to try, Is it worth trying usb install

Yep i would try the usb install, it works good for me.......

MW35
15th April, 2015, 03:52 PM
Not working here either just hangs on the Earth screen

stuball2
19th April, 2015, 10:33 PM
Not working here either, stuck on the earth too - flicking red light, tried flashing twice through the web page. Can telnet onto the box as root and top shows nothing doing.

/var/log message appears to ok for a while and then loops with this every few minutes:

Jan 1 00:37:06 dm800 user.info kernel: [ 1926.137000] bcmfb: enable manual blit
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.410000] alps_bsbe2 is in normal mode now
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.436000] alps_bsbe2 is in powersave mode now
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.454000] VIDEO0: dst_left, dst_top, dst_width and dst_height is 0.. reset to defaults!
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.454000] set current avs auto aspect to 16:9
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.454000] disable wss on display 0
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.455000] disable wss on display 1
Jan 1 00:37:06 dm800 user.warn kernel: [ 1926.455000] set sb to 3(1)
Jan 1 00:37:07 dm800 user.warn kernel: [ 1927.424000] 4905 ms: 100
Jan 1 00:37:07 dm800 user.warn kernel: [ 1927.442000] 18 ms: 1
Jan 1 00:37:07 dm800 user.warn kernel: [ 1927.510000] 68 ms: 6
Jan 1 00:37:07 dm800 user.warn kernel: [ 1927.556000] 45 ms: 20
Jan 1 00:37:07 dm800 user.warn kernel: [ 1927.880000] 324 ms: 30
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.225000] VIDEO0: dst_left, dst_top, dst_width and dst_height is 0.. reset to defaults!
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.226000] set current avs auto aspect to 16:9
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.226000] disable wss on display 0
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.226000] disable wss on display 1
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.226000] set sb to 3(1)
Jan 1 00:37:08 dm800 user.info kernel: [ 1928.389000] bcmfb: disable manual blit
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.590000] VIDEO0: set blank to 0
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.628000] sync is off so we enable it
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.628000] playback!
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.628000] total video delay: 0 (0 ms)
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.638000] VIDEO0: start decode
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.649000] flush video decoder
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.855000] VIDEO0: first pts 0x0
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.909000] VIDEO0: set blank to 0
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.910000] VIDEO0: stop decode
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.911000] VIDEO0: set blank to 0
Jan 1 00:37:08 dm800 user.warn kernel: [ 1928.912000] no decoder left in sync handling so disable xpt_sync
Jan 1 00:37:11 dm800 user.err kernel: [ 1931.487000] bcm_accel: invalid opcode! 00000080

stuball2
20th April, 2015, 04:12 PM
Installed 00.4a from the same download location and no issues installing that - tried googling the invalid opcode error, but there isn't much on it - possibly driver related? Let me know if you need more info, had this DM800 clone for a few years now and its the first image I've not been able to get to work so must be something quite specific.

I've not tried messing with the SIM package yet - is there any point in doing so? I messed it up once and had to use a patched version of DreamUp to get back into it IIRC.

Krusty
1st May, 2015, 07:31 PM
I originally had 4.0a on my DM800hd, I have upgraded to 5.0 and now the HDD will not initialize. I have gone back to 4.0a but the problem now is the HDD wont initialize on that either. Everything was fine before, any ideas as none of the hardware has been altered, the HDD worked perfect on 4a now it will noton either version. Any help on this would be great, I am sure I cant be the only one.

johnabhoy0407
4th May, 2015, 10:35 AM
Yep i would try the usb install, it works good for me.......

Is it not the case - you've got to browser flash first then do the usb install? please correct me...

andiewill
4th May, 2015, 10:49 AM
Is it not the case - you've got to browser flash first then do the usb install? please correct me...

Yes that is correct and when you do the usb install do the first part first then repaet the same sequence for the second part for the usb install, i made the mistake of doing the two parts at the same time where it just hangs on when completing the install ......

Krusty
4th May, 2015, 05:54 PM
Is it not the case - you've got to browser flash first then do the usb install? please correct me...

Thank you for the reply but my question is about an internal HDD, as I said earlier the drive was working 100% on the previous version, all I have done is flash via the browser with the latest version and now the HDD will not initialize, it throws an Error with something about the sectors not being 512. I then flashed it back to the earlier version and its the same Error. I have since removed the drive and formatted it to FAT32 and also tried EXT3 but still the same Error. I really would appreciate anyone who has solved this as I just keep going in circles.

johnabhoy0407
5th May, 2015, 06:50 PM
I had the same problem with HDD but with an earlier image too, i've disconnected it with the intention of formatting it on a pc before re-installing,
all i can think of at the moment, elt me know if you get a fix...

00360362878
5th May, 2015, 07:34 PM
Thank you for the reply but my question is about an internal HDD, as I said earlier the drive was working 100% on the previous version, all I have done is flash via the browser with the latest version and now the HDD will not initialize, it throws an Error with something about the sectors not being 512. I then flashed it back to the earlier version and its the same Error. I have since removed the drive and formatted it to FAT32 and also tried EXT3 but still the same Error. I really would appreciate anyone who has solved this as I just keep going in circles.

You can give this tool a wiz it's a free download http://www.softpedia.com/get/System/Hard-Disk-Utils/HDD-Low-Level-Format-Tool.shtml

TBH it may not be worth the trouble trying to save it, but you can always download ubuntu onto a disk (it's linux software) then start your computer from the disk. Don't install just choose trial option as install uses a fair chunk of hdd space.
You may need to read up on this, but you have a better chance of recovering this way.

good luck 003

Krusty
6th May, 2015, 01:38 PM
This is how far I have got,( I have a Genuine 800hd ) I have completely reflashed the DM800hd with latest Cobra including the Bootloader ssl84, I have also formatted the drive to fat32 and to EXT3 using various Formatting tools but every time I try and initialize the HDD I get this error ( ERROR: WARNING: Could not determine physical sector size for /dev/sda using the logical sector size 512 ). Just to recap, the drive was working perfectly ok on the previous version of Cobra, now it wont work on ether version.

00360362878
6th May, 2015, 07:25 PM
This is how far I have got,( I have a Genuine 800hd ) I have completely reflashed the DM800hd with latest Cobra including the Bootloader ssl84, I have also formatted the drive to fat32 and to EXT3 using various Formatting tools but every time I try and initialize the HDD I get this error ( ERROR: WARNING: Could not determine physical sector size for /dev/sda using the logical sector size 512 ). Just to recap, the drive was working perfectly ok on the previous version of Cobra, now it wont work on ether version.

Mate have you used the HDD Low Level format tool I have pointed you at?
http://www.softpedia.com/get/System/Hard-Disk-Utils/HDD-Low-Level-Format-Tool.shtml
There is a option to perform a quick wipe of the partition, then untick that option and format.

Then use this tool :- http://www.digital-kaos.co.uk/forums/downloads.php?do=file&id=3144
you can create a new partition and format in one application

I have used this many times and just recovered a 16g stick this way in 5mins.
I guess if you fail with this method, bin and buy a new one ?25 of the bay

Krusty
7th May, 2015, 10:03 AM
Mate have you used the HDD Low Level format tool I have pointed you at?
http://www.softpedia.com/get/System/Hard-Disk-Utils/HDD-Low-Level-Format-Tool.shtml
There is a option to perform a quick wipe of the partition, then untick that option and format.

Then use this tool :- http://www.digital-kaos.co.uk/forums/downloads.php?do=file&id=3144
you can create a new partition and format in one application

I have used this many times and just recovered a 16g stick this way in 5mins.
I guess if you fail with this method, bin and buy a new one ?25 of the bay

Just to be clear, the HDD is fine, there is nothing wrong with it. I have removed it and put it in an external usb case to check it. The problem is it wont initialize in the DM800hd (Genuine), if I go to SYSTEM-HARDDISK I can see the HDD listed, the problem starts when I choose INITIALIZE, I then get the ERROR as stated in my last post. I am not trying to recover a damaged HDD but thank you for your help.

cobra1423
18th May, 2015, 01:09 AM
Hi
Ok try this start up DCC go to Telnet and enter these commands one after the other hit enter after typing each command.
umount /dev/sda1
mkfs.ext3 /dev/sda1
mount /dev/sda1 /media/usb
if this dose not work we can try something different.
Cobra1423

Krusty
5th June, 2015, 07:28 PM
Thanks for the replies, I eventually sorted it. A little unconventional but I did it like this, I knew the HDD would initialize using a PLi image so I first loaded Pli and done that, then reflashed back to Cobra and its all working again. Except, now the EPG has decided to only update a few channels.

Krusty
13th November, 2015, 04:56 PM
Thanks for the replies, I eventually sorted it. A little unconventional but I did it like this, I knew the HDD would initialize using a PLi image so I first loaded Pli and done that, then reflashed back to Cobra and its all working again. Except, now the EPG has decided to only update a few channels.

Just wondered if there was a fix for the EPG yet as its not been working for sometime, only on FTA programmes.

Krusty
18th November, 2015, 04:23 PM
Does anyone have the EPG working on this image or at least some other way of getting it to update, the image is real nice and I dont really want to change it but would like the EPG to work.

Krusty
25th April, 2016, 04:20 PM
Just wondered if anyone has got a way yet of getting the EPG to update via another address. I like the image but would like a working EPG .....anyone ????