renault 0281011940 edc 15c3 speed limter

[shanektm450]

Hi is there anyone that can remove the speed limter from my renault traffic 2 edc15c3 I took 3 different ecu same problem even when i partialy reset ecu I cant get it to go over 90 km any help will do. The first file is original Eprom second is auto reg. for immo PS! the repair file free for all just plug in to car turn ign on wait for immo light to go off and start!
Thanks
Shane

[shanektm450]

Anyone Please!!!

[shanektm450]

Looks like no go on this any advise , what to do!!!!!!

[grzanek85]

clip programing 10 min work

[shanektm450]

clip cant do it would not change it stays on 90km/h even went to nissan to have it checked cant do it goes to adaption but fails all the time
Cheers
Shane

[easytech]

Post the flash limiter is there

[shanektm450]

Here is my flash from original ecu see if you can help
Thanks
Shane

[shanektm450]

anyone out-there! LOL!!!

[shanektm450]

I need any flash that will work even if only set to 130km

[morgano]

That flash is bad read, read again and post good ori.

[shanektm450]

Here is flash from different ECU the van is running with this flash posted above ,it was read with programmer not via obd

[morgano]

It was bad read with ptogrammer :) many zones full of FF's and should contain data. ;)


Regards,

[easytech]

Serial read is Ok i will look

[easytech]

Please try this,
I think in this file the limiter is at the gear limiters.

309521

[furburger]

Hi is there anyone that can remove the speed limter from my renault traffic 2 edc15c3 I took 3 different ecu same problem even when i partialy reset ecu I cant get it to go over 90 km any help will do. The first file is original Eprom second is auto reg. for immo PS! the repair file free for all just plug in to car turn ign on wait for immo light to go off and start!
Thanks
Shane

You have ran the van with 3 different Ecu's ? & vmax is still active ?

[easytech]

And does it goes 200km/h now?

[Novik_UA]

Here was flash from van without limiter, but it very hard to push thanks button after download, so I remove it. Sorry.

[furburger]

Here flash from van without limiter

Was this (Novik's) file read by boot, OBD or with programmer like Galep, Willem etc.. ( looks like OBD)

[furburger]

Hi is there anyone that can remove the speed limter from my renault traffic 2 edc15c3 I took 3 different ecu same problem even when i partialy reset ecu I cant get it to go over 90 km any help will do. The first file is original Eprom second is auto reg. for immo PS! the repair file free for all just plug in to car turn ign on wait for immo light to go off and start!
Thanks
Shane


Can you confirm the file named "repare" is the virgin / repair file ?

[Novik_UA]

Was this (Novik's) file read by boot, OBD or with programmer like Galep, Willem etc.. ( looks like OBD)

All EDC15 read by OBD equal to read by boot-mode, or programmer read, always is full read.

[furburger]

A clone attempt of mine failed , I asked CMD why & they replied - OBD reads writes only calibration, so u can not use it in order to clone it...


What do you think Novik?

[bobolin4o]

A clone attempt of mine failed , I asked CMD why & they replied - OBD reads writes only calibration, so u can not use it in order to clone it...


What do you think Novik?


If you want to know the truth... and you aren't too lazy...
1. Compare CMD read and read by programmer.
2. Write completely different flash dump with CMD.
3. Look again with programmer are there any differences with flashed file...
Easy like a mushroom soup.
Nothing to say more...

[furburger]

I've put the repair file in as it's presented here and got engine running but glow plug lit. Maybe I should have applied the mods only to my customers original e2p?!