PDA

View Full Version : Passat edc17, problem with ecu after obd writing


bugarcek
21st April, 2015, 02:57 PM
Hello

I have problem with Vw passat 2.0 tdi 140 hp manual 2009 year.

ecu hw: 03L907309


I read this ecu with galleto via obd. All was ok. I made egr off file and write it without a problem via obd on ecu.

Now after 3 months I tried to do also some dtc off on this ecu, I used my old obd read file, mod it and write back to ecu. Than I get error at end of writting and car does not start. (Customer was on official service 1 moth ago, he told me now)

Now I attached ori file readed by obd 3 moths ago and my full boot read.


Thanks for any help
mario38
21st April, 2015, 03:21 PM
I think your file egr off is wrong ..
Depending on what maybe the problem is the miscalculation of cks in the second writing ..
you try to write the file that worked before though egr is not off to 100%
bugarcek
21st April, 2015, 03:35 PM
I tried at least 10 times. Every time error...
morgano
21st April, 2015, 03:41 PM
Updated ecu at dealer, t-prot active now. Seems not hard to guesss what have happend.
bugarcek
21st April, 2015, 03:43 PM
Yes... If knew before that car was at the dealer. I would not do that... What should I do now?
wiski
21st April, 2015, 05:24 PM
Tprot not active. Maybe if you can check with VCDS date of last flashing (if it was flashed at dealer)
bugarcek
21st April, 2015, 05:38 PM
Tuesday,21,April,2015,18:37:51:04354
VCDS Version: Release 14.10.1
Address 01: Engine
Control Module Part Number: 03L 906 022 QC
Component and/or Version:
Software Coding:
Work Shop Code: WSC 00000
VCID: 76E3E5D101D63F9144C-8023


Flash Status
Programming Attempts: 10
Successful Attempts: 2
Programming Status: 10000000
Required Conditions: 00000000
Flash Tool Code: 00032 257 66565
Flash Date: --.--.--
Misc.
Hardware number: 03L 907 309
VCDS Info:
Labels: 03L-906-022-CBA.clb
Readiness: No script available
bugarcek
21st April, 2015, 05:41 PM
03L906022QC 3732 I need this file.
wiski
21st April, 2015, 06:13 PM
Write by boot , let the tool make chks.
bugarcek
21st April, 2015, 06:44 PM
Still error at the end and car does not start
tunertool
21st April, 2015, 07:41 PM
Your original boot mode backup you can't write it? I can help with this....
bugarcek
21st April, 2015, 07:43 PM
I do not have original boot mode backup... I boot mode read after obd fails.
kire106ka
22nd April, 2015, 12:44 AM
You can try to write these file
bugarcek
22nd April, 2015, 09:29 AM
Does not work. Is there any way of getting all read (eeprom plus flash) And immo off the flash?

EDIT: I load again kire106ka file via boot mode and noticed, that glow plug light comes up. But car did not start, after that I load the same file again via obd and car just started. Impressive....

kire106ka THANK YOU VERY MUCH
kire106ka
22nd April, 2015, 10:49 PM
No prob friend when i have free time i help always
artut7
13th March, 2020, 02:41 PM
You can try to write these file
HI i have the same problem, can you give me password to open files?
jurebv
13th March, 2020, 04:40 PM
their files wont work for you...upload your boot and obd
artut7
13th March, 2020, 06:03 PM
their files wont work for you...upload your boot and obd
I cant open with winrar becouse ask me for a password.
morgano
14th March, 2020, 10:22 AM
I cant open with winrar becouse ask me for a password.

Read man what it was adviced to you, “his files will not work on your broken ecu” you need upload readings from your damaged ecu to try to get them fixed. So you need his password for nothing, read bootmode your ecu as is now, also upload the obd readings and wait.